|
|
PART # SBS BCT-5000
DC RESISTIVE LOAD BANK (24, 48, & 120 VDC)
The only way to know your industrial batteries will perform to specification is to test them regularly. SBS's battery capacity testers enable you to test your wet or sealed batteries in a variety of ways and at three voltages. Load bank test 24V, 48V, or 120V DC systems with currents up to 171 amps. A built-in digital meter lets you read volts, amps, amp-hours, and elapsed time without having to hook up a separate meter. The display is accurate to 1% of full scale at the rated voltages. The unit also offers continuous operation, so there's no cool down needed after or between tests. Use the master load control switch to instantly apply or remove loads.
|
|
Testing of insulation plays a great role in electrotechnics.Dielectric breakdown tests are important to the safe functioning of everything from power distribution transformers to household appliances. Impulse voltage tests are characterized by a 1.2/50us waveform. This is as industry standard.
The huge range of devices to be tested requires impulse generators from a few hundred volts(V) up to hundreds of thousands of volts(kV). The impulses have low energy content, but this can vary depending on the application.
EMC PARTNER offer a range of instruments starting from 250V up to 100kV. All units have the necessary connections and safety features relative to the test.
Many product specific standards incorporate insulation testing as part of the safety criteria.
|
|
|
|
|
|
FULLTEST4058 model was designed from HT ITALIA to performing essential tests in industrial environments on electrical machines devices and partially type-tested assemblies (PTTA) in compliance with EN60204-1 and EN60439-1 respectively.
The meter principally performing Continuity test on potential equalising conductors with >10AAC test current, Insulation Resistance with 500VDC test voltage and Withstanding tests with 1000AC test voltage (for electrical machine devices) and 2500V test voltage (for individual test on PTTA assemblies switchboards).
Withstanding test is performed also in BURN mode with no limits on trip-out current. Discharging Time measures of internal capacitance and on external plugs of device under test complete the list of possible test with this meter.As FULLTEST4050 more advanced model also FULLTEST4058 have a built-in internal memory to save all measurement results and a RS-232 PCs interface for directly transfer of saved tests by dedicated Windows software.
The model is fitted inside a practical and protected plastic case board with no flammability and a membrane keyboard for rapid selection of functions is included on the frontal panel together a wide custom display.
FULLTEST4058 is the ideal solution for any kind of verifier and/or industrial installer to performing easily and rapid test on industrial appliances.
|
|
Short description :
For both Ground Fault and Standard outlets. Features a power quality monitor and a Nuisance Trip test. Use to check line, neutral and grounding wire integrity. To test GFCI's for proper operation and nuisance tripping. Can also be used to identify excessive voltage drop by measuring voltage between line and neutral.
|
|
Proper grounding is absolutely crucial for safe, uninterrupted operation of equipment, and is the most essential component of any ESD/EMI management system. Common tool and equipment problems are largely due to ground and power related issues or excessive noise (EMI) on the ground line.
|
|
The S1-552 is an advanced 5kV insulation tester with a high output current and many time-saving features. A large, analog/digital LCD shows resistance valves up to 5 T%u03A9 and incorporated a timer and other test information. The output current, of up to 5mA, speeds up testing by charging capacitive loads quickly.
The 5 and 15-kV Megohmmeters are high-voltage, line operated instruments that can be used on all types of insulation tests ranging from 500 volts to 15 kV.
With over twenty 1-kV models to choose from, selecting the proper Megger insulation tester can appear a bewildering task at first. Actually all the process requires is a little organization. All Megger insulation testers perform essentially the same test in fundamentally the same manner %u2014 accurately and reliably. Refinements and added features, however, separate one model from another in application and operator appeal.
|
|
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.
It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
|
|
|
The partial discharge measurement of electric motors and generators during the current enterprise is world-wide increasingly used. Thus isolation problems can in time be recognized and revision work be better planned.
|
|
- Waveform (Range):Oscillation (up to 4 µF, Vmax 6000 V; 4 µF up to 10 µF, Vmax 4000 V)
- Coupling:up to 800 V rms/16 A for <= 6 s / up to 380 V rms/16 A for continuous operation
- Standards:IEC 60348-14 Amd.1,
- Options:EN 132400
- Required Accessory:Coupling Switch Matrix TC-MIG24, TEMA
|
|
Features
Programmable Test Current to 40 Amps
50-400Hz Programmable Current Frequency
Local/Computer Programmable
Programmable Resistance Limits
Programmable Test Time Durations
AC Ohmmeter to 10uOhms Resolution
Tests to UL/IEC Specifications
|
|
Clamp-On Ground Resistance Testers
The Clamp-On Ground Resistance Testers measure ground rod and grid resistance without the use of auxiliary ground rods. Offer accurate readings from 0.01 to 1200Ω as well as ground leakage current from 1mA to 30Arms without disconnecting the rod under test.
|
|
MEGATEST-1
Digital Insulation Tester
Large LCD display with 60 segment bar graph
Test voltage 250, 500 V, 1000 V DC
Insulation measurement to 4000 M&Mac189;
Voltage to 600 V AC/DC
Acoustic continuity test
Memory for 4,000 test values
with RS-232 interface
CAT III 600 V
|
|
|
AEMC® manufactures a complete line of insulation testers designed to test the quality of insulation using 1000V test voltage required for testing equipment designed to be powered by 480VAC. Both analog and digital meters are available. AC powered, battery powered and hand crank models are available. Most models will measure into the GΩ and TΩ range. Most models offer multi-function capability, measuring AC/DC volts, resistance and continuity as well as insulation resistance. Both hand held instruments and rugged instruments built into portable cases are available.
|
|
|
|
|
|
C.A 6549
In its site-adapted casing, the C.A 6549 insulation tester offers quantitative and qualitative insulation analysis, on a large backlit graphic screen!
· measurement range: 10kΩ to 10TΩ!
· 4 fixed test voltages: 500 / 1,000 / 2,500 and 5,000V
· adjustable test voltage position: 40 to 5,100V in 10V or 100V increments
· step voltage mode: R(Utest) measurement curve viewed on the screen and gradient calculated automatically in ppm/V
· DAR, PI and DD quality ratios calculated automatically
· programmable test length and R(t) measurement curve displayed directly on the screen
· with indication of measurement t° after measurement, resistance recalculated to reference temperature for reliable and accurate insulation monitoring
· many other functions: test voltage locking, smooth function, programmable alarms, etc.
· can record thousands of measurements
· RS 232 connector for connection to PC or very compact serial printer
· power supply: rechargeable NiMH battery for 30 days' operating with 10 DAR measurements and 5 PI measurements per day
· electrical safety: IEC 61010-1 Cat.III 1,000V or Cat.I 2,500V and 61557
· dimensions: 270x250x180mm; mass: 4.3kg
|
|
Maximum 5kV Test Voltage - Up to 5TΩ of Insulated Resistance Testing
Safely evaluate the insulation characteristics of high voltage transformers, motors and cables
Measure insulation of high-voltage equipment (such as transformers, cables, and motors)
Automatically calculate and display the PI (Polarization Index) and DAR (Dielectric Absorption Ratio)
Temperature compensation to accurately respond to variations in insulation material
Data storage and USB interface
|
|
Leakage Current Measurement Essential for Electrical Safety
Automatically compatible with Networks stipulated by IEC/UL/JIS standards
Automatic measurement function (Measuring power supply polarity switching as well as the normal state / single failure state)
Stores data for 100 units
Power supply separation
|
|
Our capacitance bridge performs measurements in conditions that are beyond the scope of most conventional Capacitance Bridges, by the use of a well proven transformer ratio-arm design. Test sites such as high voltage switch yards, transformer stations, and production areas with a high presence of electrostatic interference do not have adverse effects on this instrument. Measurements on three or four terminal devices can be done without calculation by the use of the GUARD system. This low voltage test set is designed to test electrical insulation qualities in the laboratory, substation or maintenance shop, without the dangers associated with using a high voltage test set.
Features
* Capacitance testing for precise determination of capacitance and dissipation factor (C&DF)
* Important for preventive maintenance, production testing and cable fault finding
* Extremely useful for measuring dielectric properties of power transformers, bushings, cables, and power factor correction capacitors.
|
|
MIT410TC and MIT430
Insulation Resistance and Continuity Testers
• Insulation testing up to 1000 V and 200 G?
• Patented analog arc and dual digital display
• CAT IV 600 V rating
• TRMS & DC Voltage measurement
• Continuity testing at 200 mA or 20 mA down to 0.01
• Pass/Fail limit alarms
• PI/DAR and Timer function
• Test result storage (MIT430)
• Bluetooth® wireless data transfer (MIT430)
• Three year product warranty
• IP54 rated
|
|
FEATURES:
1. DIM 571 is a LCD Indicated instruments for insulation (M Ohm), Continuity (OHM) and AC Voltage
2. Three Insulation test voltage (DCV): 250V, 500V, 1,000V.
3. Large LCD display(68 x 34mm)
4. Test Insulation at rated voltate into 1 1mA load
5. 200mA short circuit continuity current.
6. Timer for test functions (3 ~ 5 minutes)
7. Data Hold function
8. Auto power off function
9. Automatic circuit dischage
10. Fuse proection
11. EN61010 CAT III 600V
12. BS 16" Edition
|
|
The IRT 1557 is a small, lightweight insulation resistance and continuity tester. Hand-held, it's a superb addition to any test engineer's toolkit.
It performs measurements according to BS 7671 16th/17th Edition Wiring Regulations and Part P. Seaward's unique integrated safety probe puts the LCD and test probe in the user's line of sight whilst making measurements, no other tester does this. IRT 1557 is fully compliant with EN 61557 and IEC 61010-1 600v CAT lll. Automatic discharge of capactive circuits, it gives you automatic warning of the presence of hazardous voltages.
It comes with an easy to use rotary setting switch. The IRT 1557 offers a number of unique features, including voltage measurements up to 1000AC or DC and a dual safety rating. With incredible robustness the IRT 1557 provides all the tests you need with a safe feel.
|
|
1040 1000V Megohmmeters
The Megohmmeter Model 1040 is a battery powered digital insulation resistance tester. It is designed to measure insulation resistance, continuity, voltage and to measure resistance. The Model 1040 tests are 500 and 1000V. It incorporates a 600V voltmeter which automatically detects and accurately displays AC/DC voltages in the test circuit on each of the insulation test voltage ranges. Above 25V it also provides an audible and visual signal, and inhibits further tests, thus protecting the user and the meter.
An exceptionally large digital/analog multi-function display provides clear and easy readings enhanced by a bright blue electroluminscent backlight.
|
|
5000V Megohmmeters
AEMC® manufactures a complete line of insulation testers designed to test the quality of insulation using 5000V test voltages required for testing large motors, generators, transformers and cables. Both analog and digital meters are available. AC powered and battery powered models are available. Most models will measure into the GΩ and TΩ ranges. All models offer multi-function capability, measuring AC/DC volts, resistance and continuity as well as insulation resistance. Both hand held instruments and rugged instruments built into portable cases are available.
|
|
1000V Megohmmeters
AEMC® manufactures a complete line of insulation testers designed to test the quality of insulation using 1000V test voltage required for testing equipment designed to be powered by 480VAC. Both analog and digital meters are available. AC powered, battery powered and hand crank models are available. Most models will measure into the GΩ and TΩ range. Most models offer multi-function capability, measuring AC/DC volts, resistance and continuity as well as insulation resistance. Both hand held instruments and rugged instruments built into portable cases are available.
|
|
1039 100V Megohmmeters
The Megohmmeter Model 1039 is a battery powered digital insulation resistance tester. It is designed to measure insulation resistance, current, capacitance, cable length, voltage and to measure resistance. The Model 1039 tests are 50 and 100V. It incorporates a 600V voltmeter which automatically detects and accurately displays AC/DC voltages in the test circuit on each of the insulation test voltage ranges. Above 25V it also provides and audible and visual signal, and inhibits further tests, thus protecting the user and the meter.
An exceptionally large digital/analog multi-function display provides clear and easy readings enhanced by a bright blue electroluminscent backlight.
|
|
METRISO 5000A: analog high-voltage insulation measuring instrument with 4 measuring voltages: 100, 250, 500
and 1000 V (per EN 61 557 part 2) and 1500, 2000, 2500 and 5000 V
METRISO 5000AK: The battery powered METRISO 5000 A is converted into the muscle powered
METRISO 5000AK by replacing the battery module with a crank generator.
- Extensive measuring range: 10 kOhm... 1 TOhm
- Measuring range: 100 kOhm... 100 MOhm (1000 V)
- Measuring voltages: 100 V, 250 V, 500 V, 1000 V, 1500 V, 2000 V, 2500 V, 5000 V
- Measurements to 1000 V per DIN VDE 0413
- Voltage measurement to 2000 V ,
- Concise logarithmic display
- Guard terminal for the elimination of surface current
|
|
Teraohm, is an ultra high range insulation resistance testing instrument with an output voltage of up to 10000 volts dc. It will measure up to 10 TeraOhms (10,000,000 MegaOhms). This insulation tester is suited for transformer, generator and large motor insulation resistance testing.
Features
* Insulation resistance measurement up to 10 TeraOhm (10,000,000 MegaOhm)
* Output voltage up to 10 kV in steps of 25 V
* Diagnostic tools (PI, DAR, DD)
* Fast charging of capacitive loads using 5 mA current source
* Automatic discharge of capacitive charge
* Large display with digital and bar-graph results
* Optional TeraLink Pro PC software for MS Windows®
|
|
Featuring Four Instruments in One
AC Hipot to 7KV
DC Hipot to 10KV
Earth Continuity Testing 1mOhms
Insulation Resistance 65GOhms to 2500V
Arc Detection with usec shutdown
Programmable
IEEE-488.2, RS232 Interfaces
|
|
Features/Benefits
Increases test throughput
Reduces operator exposure to high voltage
Improves test quality, consistency and repeatability
Enhances end product quality and reliability
Scans up to 48 points with a single compact unit
Rated to 7kVDC or 5kVAC
GPIB/RS232 standard
May be controlled directly by Vitrek Hipot Tester
Available QuickTestTM graphical programming software
|
|
- LCD Display 320 x 240
- File Management(Flash Memory Card)
- Test Point Range : 64-2048
- Test Voltage : 50 - 1500VDC(RT-9980H/CH), 50 - 1000VAC(RT-9980H/CH)
- Insulation Test : 500K-1000MOhm(RT-9980 H/CH)
- 4-Wire Rsistance Test : Yes(Option)
- Components Test : Resistor,Diode,Capacitor(Option)
- Resistor Measurement : 0.1Ohm-20MOhm
- Capacitor Measurement : 100pF-1000uF
- High Quality Relay
|
|
Multi-purpose coupling unit for CPC 100
CP CU1 is a coupling-unit designated for measurements with the CPC 100 test system on overhead lines and power cables. Typical applications of this world-wide unique system include: Line impedances and k-factors of overhead lines or power cables, Mutual coupling of parallel lines, Coupling of power lines into signal cables,
Ground impedances of large substations, Step and touch voltages.
The test system offered by OMICRON makes use of frequency shift techniques for accurate measurements regardless of electrical interference.
Applications
- Line impedance and residual compensation factor (k-factor) measurements
- Positive and zero sequence impedance measurements of power lines
- Measurement of mutual coupling of parallel lines
- Measurement of ground impedances of large substations
- Step and touch voltage measurements
- Measurement of coupling impedances between power lines and signal cables
|
|
|
|
