|
|
Magnetic flux control plays a key role in optimal coil design. We offer custom induction coil design to maximize production efficiencies to produce better parts for less cost.
As a starting point in assisting you in induction coil design, our engineering department makes a detailed analysis of the product heat treatment requirement and production environment (i.e.,workpiece material/geometry, heat treatment specification, production rate, sequence of operations, material handling equipment and available induction heating system parameters, etc.) and then considers other coil development stages including:
Heating style (limited control due to exisitng machines or bill of process)
Inductor design (coil style selection, copper cross-section, controller manufacturing & application, etc.)
Inductor engineering & fabrication
Inductor matching
Inductor set-up and tests
Final modification of inductor & process (if required)
|
|
Magnetic flux control plays a key role in optimal coil design. We offer custom induction coil design to maximize production efficiencies to produce better parts for less cost.
As a starting point in assisting you in induction coil design, our engineering department makes a detailed analysis of the product heat treatment requirement and production environment (i.e.,workpiece material/geometry, heat treatment specification, production rate, sequence of operations, material handling equipment and available induction heating system parameters, etc.) and then considers other coil development stages including:
Heating style (limited control due to exisitng machines or bill of process)
Inductor design (coil style selection, copper cross-section, controller manufacturing & application, etc.)
Inductor engineering & fabrication
Inductor matching
Inductor set-up and tests
Final modification of inductor & process (if required)
|
|
Manufacture of induction coils
made of enamelled copper for low and medium voltage (since 1976).
Winding in cylindrical or oblong form, in one or two layers, in enamelled or bare copper with stripped, tinned or headed ends and possible positioning of the core.
|
|
Fluxtrol concentrator manufacturing and application technique plays a very important role in successful performance of induction coils. With respect to Fluxtrol concentrator application - magnetic, thermal and mechanical aspects must be considered. Additionally, the electrical strength of our concentrator must be considered or insulation provided.
This section is intended to provide methods for safety, handling and machining FLUXTROL® & FERROTRON® concentrator materials when applying the product to induction coils.
|
|
| ... products without technical information |
| |
Advantages:
- Easy-fit basic frame
- Slim
- Easy connections
- Certain models may be delivered contained in a housing
- A wide range of options
Range :
- Several models and one range available on request
- Air flow rates: 500 to 80,000 m³/h
- BSH EC: Standardised coil in the SILENTHERME range, air flow rates: 1,000 to 10,000 m³/h
Use :
Circulates a fluid to warm or cool the air in commercial, industrial or healthcare facilities. May be ducted.
Description :
- Galvanised steel frame
- Various tube and fin types available
- Connections: tapped couplings with air bleed valves or smooth tubes
- A wide range of options
Features :
- Conception et dimensions et figées
- Nombreux modèles en stock
- Débit d'air de 200 à 80 000 m3/h
- Disposition verticale ou horizontale
|
|
The unit involves an exchange between 2 fluids: a primary fluid in the tubes (water or gas) and a secondary fluid on the fins side (air or gas).
This exchanger offers many options in terms of materials and construction: dimensions, type and materials used in the tubes, fins, etc.
|
|
Heating & Cooling coils
Thermofin’s MP and UG heat exchangers are custom made to meet your needs. By optimizing the mechanical and thermal design in accordance with your specific requirements, Thermofin’s team of enfineers and designers will insure you get the right equipment for the job.
|
|
Steam coils
Based on its vast experience in steam equipment and systems, Thermofin has developed its own steam coil design and selection software. Our control of the construction process, from design to fabrication enables Thermofin to offer the end user a variety of materials and arrangements, making our range of steam coils as diverse as your applications. Therefore, whether the steam is in vacuum or at high pressure, there is always a Thermofin steam coil that will satisfy your needs.
|
|
GEOMETRIES
Thermokey’s concept is to satisfy any type of application. A broad array of geometries are therefore available:
- 25x21,65mm with 3/8” or 5/16” tube
- 30x25,98mm with ½” or 3/8” tube
- 50x43,3mm with ½” or 5/8” tube
- 42x36,4mm with ½” or 5/8” tube
FINS
The fins can be supplied in aluminium, copper, tinned copper, prepainted aluminium, double coated or in stainless steel AISI 304; they are provided of spacing rings, these guarantee a perfect fin spacing and contact with the expanded tubes. A special high efficiency corrugated fin is used for a higher performance if compared to normal corrugated fins; a special extra high efficiency louvered fin is also available.
|
|
GEOMETRIES
Thermokey’s concept is to satisfy any type of application. A broad array of geometries are therefore available:
- 25x21,65mm with 3/8” or 5/16” tube
- 30x25,98mm with ½” or 3/8” tube
- 50x43,3mm with ½” or 5/8” tube
- 42x36,4mm with ½” or 5/8” tube
|
|
| ... products without technical information |
| |
Thalassa fan convector are reversible heating and air conditioning.
The offered range includes 4 models and 5 sizes, with powers from 5 kW cold production and 11 kW hot production.
Since there is poor residual pressure with this equipment (20 Pa), they are used preferably for direct blowing either hanging or wall mounted, with or without casing.
Easily integrated in any type of premises due to its discrete presentation and RAL 9010 epoxy painted frame.
Aircalo offers a wide scope of flow control customization.
|
|
|
|
|
|
Major 2
The Major 2 fan coil unit is designed to be mounted vertically on a wall or horizontally below ceilings to heat and cool homes, businesses and industrial and healthcare facilities. Not only does it combine the economic benefits of installing and operating a central boiler and chiller plant, it also allows individual temperature control in all rooms.
Available in six sizes and two models:
- CH: horizontal cased,
- CV: vertical cased.
Heating capacity: 2 to 20 kW
Cooling capacity: 0.6 to 8 kW
Air flow rates: 115 to 1300 m³/h
- Polymer casing with solid RAL 9010 finish,
- Two access doors lead to air bleed valve and control terminal,
- Water coil: two or four tubes or two tubes and electric heater,
- Condensate drain pan,
- Seven-speed motor (three factory-wired speeds) with balanced, double-inlet aluminium blower wheel,
- Mounting bracket frame,
- Regenerative polyester fibre filter. Efficiency class: G3 (EN 779),
- Fully enclosed electrical junction box,
- A wide selection of control options.
|
|
Floor Standing Type
This space-saving design with a slim shape and smart vent line offers the least obstruction to the surrounding area.
* The unit can be easily installed on the floor along the wall or under the window. Maintenance is simple.
* This type can be hung on the wall for easier cleaning.
|
|
Terminal air heater
"Drawer-type" heaters, which are designed to be installed directly in an opening made in the duct, are built around stored elements. They are bent upon request and can be delivered in small series in a week.
For ducts diameter from 100 to 630 mm and rated from 500 W to 36 kW, the terminal heaters for circular ducts are assembled using elements kept in stock. They may be delivered in small series within 48 hours.
A series of self-controlled circular terminal heaters was developed to satisfy the desire of users for precise temperature control in each room. They can be controlled by electronic thermostats or remote industrial controllers. Many safety accessories are optionally available.
|
|
| ... products without technical information |
| |
|
|
|
|
ENCAPSULATED COILS
These coils have a natural application in the field of solenoid valves for the most varied sectors.
The range is composed of numerous types, with different dimensions, powers, materials and electrical connections. The standard versions and the availability of developing new ones, allow optimum solutions for even the most complicated demands.
LINEAR SOLENOIDS
These solenoids are used in the most varied industrial applications where there are demands for linear actuations.
They are available with galvanised steel body or with encapsulated coils, allow an high number of hourly operations and guarantee an extremely long life cycle.
HOLDING SOLENOIDS
The holding solenoids, designed to operate in DC, are characterised by a rugged body in galvanised steel.
The range allows for external diameters from 19mm to 70mm. Holding force goes up to 1.300N. This feature is even more relevant considering the possibility of continually operating at ED100%.
LOCKING SOLENOIDS
DELTA production is aimed at constructive choices for both simplicity and robustness, guaranteeing maximum reliability and efficiency. They are available in three different sizes, all have a built-in return spring and are produced with encapsulated coils or with stainless steel body.
|
|
The actuator is composed of a magnetic circuit with a permanent magnet creating a magnetic force in the air gap.
In this air gap moves the coil linked to the actuation shaft.
The current that circulates in the coil reacts with the magnetic field and thus generates a mechanical force which is transmitted through the actuation shaft.
This force is directly proportional to the current, in direction and intensity.
Many diametres possible :
Diametre 30
- ref AE G31 stroke 6mm
- ref AE G32 strokse 12mm
Diametre 40
- ref AE G41 stroke 6mm
- ref AE G42 stroke 12mm
Diametre 50
- ref AE G51 stroke 6mm
- ref AE G52 stroke 12mm
|
|
CVC - Circular Voice Coil Series
CVCA - Circular Voice Coil Actuator Series
- Direct drive
- Zero cogging
- Zero backlash voice coil motors
- Low coil mass with very fast reponse and high bandwidth
- Short Lead Time
- Economic Price
- Compact Size Good Cost Performance Ratio
--------------------------------------------
CVCS - Circular Voice Coil with Shaft
- Voice coil with build in bearings systems
- plug and play, no additional mechanical structure or bearings systems required
- center hollow to allow for vacuum suction
- ideal for pick and place head
- allow position, velocity, torque control
- high force (speed) small size
- optional module using stepper motor for theta adjustment
|
|
BEI Voice Coil Actuators are ideally suited for such demanding Applications as semiconductor equipment, defense systems and life-sustaining medical systems, BEI Kimco Magnetics Voice Coil Actuators are directdrive, hysteresis-free, cog-free devices offering high-acceleration and “clean” technology. They deliver infinite position sensitivity, limited only by resolution of the feedback device. These units exhibit perfectly smooth force-versus stroke characteristics. New packaging and miniaturization capabilities offer the designer added flexibility without compromise. Units can be packaged for integrated assemblies including encoder, motor, switch or other functions to streamline operations and cost.
|
|
| ... products without technical information |
| |
Thalassa fan convector are reversible heating and air conditioning.
The offered range includes 4 models and 5 sizes, with powers from 5 kW cold production and 11 kW hot production.
Since there is poor residual pressure with this equipment (20 Pa), they are used preferably for direct blowing either hanging or wall mounted, with or without casing.
Easily integrated in any type of premises due to its discrete presentation and RAL 9010 epoxy painted frame.
Aircalo offers a wide scope of flow control customization.
|
|
|
|
|
|
Major 2
The Major 2 fan coil unit is designed to be mounted vertically on a wall or horizontally below ceilings to heat and cool homes, businesses and industrial and healthcare facilities. Not only does it combine the economic benefits of installing and operating a central boiler and chiller plant, it also allows individual temperature control in all rooms.
Available in six sizes and two models:
- CH: horizontal cased,
- CV: vertical cased.
Heating capacity: 2 to 20 kW
Cooling capacity: 0.6 to 8 kW
Air flow rates: 115 to 1300 m³/h
- Polymer casing with solid RAL 9010 finish,
- Two access doors lead to air bleed valve and control terminal,
- Water coil: two or four tubes or two tubes and electric heater,
- Condensate drain pan,
- Seven-speed motor (three factory-wired speeds) with balanced, double-inlet aluminium blower wheel,
- Mounting bracket frame,
- Regenerative polyester fibre filter. Efficiency class: G3 (EN 779),
- Fully enclosed electrical junction box,
- A wide selection of control options.
|
|
Floor Standing Type
This space-saving design with a slim shape and smart vent line offers the least obstruction to the surrounding area.
* The unit can be easily installed on the floor along the wall or under the window. Maintenance is simple.
* This type can be hung on the wall for easier cleaning.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
