|
|
|
Models with max output power from 35 kW to 500 kW. EKOHEAT induction heating systems for 5-15 kHz range provide reliable and repeatable solutions for heating with large coils or for heating larger parts. Among the many typical applications are heating of hard-to-couple parts, deeper heat penetration, crystal growing, heat treating steel, preheating for forging of steel, aluminum, copper or brass, and melting in crucibles.
|
|
|
The EKOHEAT Compact model is versatile, rugged & easily integrated into existing manufacturing cells. The power control system delivers output power from 100 W to 15 kW with 100% duty cycle at output frequencies from 50 to 150 kHz, CE marked with a wide range of standard features & functions. Ambrell’s new AutoTap technology is used for challenging applications where steel is heated through Curie temperature, automatically adjusting for the varying electrical load during this transition.
|
|
Performance:
The CXH series of hybrid, high frequency power supplies is designed to operate at a fixed frequency over the range of 2 to 40 MHz. The rugged amplifier design is well suited to demanding industrial applications where stability and reliability in the presence of erratic loads is required. The solid-state driver section features microprocessor control for precise power control and diagnostic monitoring.
Applications:
The CXH series of high power supplies provides stable, reliable RF power for industrial heating applications including drying, plastic welding, silicon crystal growing and flat panel.
Features:
Standard power ranges: 15kW, 25kW and 50kW
Rugged, reliable design for years of trouble-free operation
Simplified operation through microprocessor- controlled user interface
CX series solid-state driver requires no tuning or adjustments
Water cooling increases tube life by reducing thermal stress in high VSWR mismatched loads
RS-232 package standard
ETL Mark on CXH 25kW
|
|
|
|
|
|
STATIPOWER SP11 Induction Power Supply
Features/Benefits
* 50-200 kHz with a wide range of power outputs for application flexibility
* Continuous or intermittent duty
* 100% solid state design. Ideal replacement for less efficient oscillator tube power supplies
* High, 0.95 input power factor under all operating conditions
* ±1% output regulation accuracy with ±10% line variance under all operating conditions
* Single control board for reliable operation and simplified maintenance
* Analog display of voltage, frequency, current and output power. Built-in digital heat timer
* Optional RS-232/485 interface for automatic operation under computer control
* Built-in load matching capacitors and variable ratio isolation transformer
* Built by the world's largest designer and manufacturer of induction heating equipment
The STATIPOWER® SP11 is a self-contained, stand-alone solid state transistorized power supply for heating a wide variety of parts. Application capabilities include hardening, tempering, brazing, soldering, melting, bonding and shrink fitting. A broad range of single-turn and other low impedance heating coils can be properly matched with built-in load tuning capacitors and multi-tap output isolation transformer.
|
|
|
|
|
|
STATIPOWER SP5 & 7 Induction Power Supply
Features/Benefits
* Multiple power/frequency combinations for application matched performance
* "Bullet-Proof" circuitry eliminates nuisance shutdowns and restarts
* Voltage fed for 0.95 input power factor over full operating range
* Output regulation by voltage, power or current. Jumper selected
* Single control board. Field replaceable for easy maintenance and trouble shooting
* Interchangeable control board. Factory calibrated to eliminate field adjustment and calibration
* Modular, single-layer design for easy access and maintenance
* Pressure switches on all capacitors to shut down system before complete capacitor failure
* Built-in annunciator panel for simplified status/fault diagnostics
* < 85 dB operating sound level for quiet operation
Job-Matched Induction Heating Power Supplies:
STATIPOWER® SP5 & 7 water-cooled, solid state power supplies are designed for case hardening, through hardening, annealing, mass heating and many other applications. Power and frequency combinations from 10 to 1,300 kW/1 to 25 kHz are available in single and dual frequency models.
|
|
MF and RF generators for inductive heating processes
Induction Heating - briefly illustrated
Induction heating is based on the physical effect that most electrically conductive materials heat very quickly and efficiently when exposed to a high frequency magnetic field. By induction, energy can be rapidly and precisely transferred into the work piece without physical contact with the heat source. HÜTTINGER’s induction generators provide robust, reliable and stable performance even in the harshest of production environments. Our animation shows the principle of induction heating process.
|
|
| ... products without technical information |
| |
|
|
|
|
Powerbox Greenhub 1000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 1000W of peaking power
- the maximum power in continuous use: 800W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 14 l/min.
Included in the system Powerbox GreenHub 1000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
|
|
|
Powercell Greenhub 4000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 4000W of peaking power
- the maximum power in continuous use: 3800W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 56 l/min.
Included in the system Powerbox GreenHub 4000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
|
|
|
Powercell Greenhub 5000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 5000W of peaking power
- the maximum power in continuous use: 2700W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 70 l/min.
Included in the system Powerbox GreenHub 5000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
|
|
|
Powercell Greenhub 3000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 3000W of peaking power
- the maximum power in continuous use: 2700W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 42 l/min.
Included in the system Powercell GreenHub 3000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
|
|
|
Powerbox Greenhub 2000
Line GreenHub di Powerbox H2planet, that is all the one which you have always asked from an independent energetic system:
like the current of house but with all the advantages of energetic independence. Ideal like group of continuity, unit of emergency generation, unit of generation from field, but also like domestic generator for the isolated rooms with lowlands every day requirements.
Technical detailed lists
- till 2000W of peaking power
- the maximum power in continuous use: 1800W
- exited in alternating current BTicino 220V (sinusoidal pure)
- the maximum hydrogen consumption
- feeding 2-6bar
- hydrogen: degree 4,5 minimum (gas dry)
- hydrogen consumption to max power: 28 l/min.
Included in the system Powerbox GreenHub 2000:
- it arranges with car-humidification system stack (NOT PRODUCED REFUSE)
- handles in rubber for the transport
- possible recovery arranges of GreenAir aeration for maximum performances stack and warm air for cogenerativo use
- holes threaded posterior for the wall implantation
- attack ultrasure express to lowland pressure
- shop for approached express inner
- timer programmabile for programs ignition weeklies magazine/standy
- inverter integrated DC/AC and DC/DC
- escape 220-230VAC @ 50Hz
- escape 12/24VDC for recharges batteries
- escape 5V USB 2,0 for all the electronics
- emergency sensors standard: losses hydrogen, inner temperature, pressure for control level hydrogen, antiscassinamento
Optional:
- remote control iGreen GSM/GPRS smartphone/iPhone over IP
- slowly of substitution to by-wire (iGreen necessary) of hydrogen bottles
- programmed maintenance
|
|
|
Powerbox 500 is a fuel-cell system for electric current production at zero emissions. A super-compact500W system (550W peak), ideal for fuel-cell small applications: modeling, robotics, automation, small electric vehicles or any other portable application.
|
|
|
Rugged. Reliable. GenCore® fuel cell systems. With unmatched availability and scalable DC power, GenCore fuel cells outperform batteries and generators without any of the associated drawbacks. It’s the best solution for your back-up power requirements. Because you don’t want to know when the power comes back on, you only want to know that it never went out.
|
|
... see all the products in the category
Fuel cells
|
|
The Meech Model 904 is a constant voltage power supply, designed to provide a 7kV source for Meech AC ionising equipment. It is adjustable to operate at 100-120v or 200-240v input voltages and is available in either 50Hz and 60Hz versions to suit local conditions. The 904 utilises a modified shape of output wave form and is uniquely designed to allow automated manufacture for increased reliability and extended product life.
|
|
|
The 977CM - Current Monitoring Pulsed DC Controller, brings together powerful long-range ionisation; closed-loop feedback; self-monitoring and remote reporting. A complete package, unique to Meech. Self-monitoring and adjustment of performance allows optimum control of static for much longer periods than previously possible. Local display and output signals alert operators to the need to clean the equipment.
|
|
|
The Model 977v3 Pulsed DC Controller has been designed to operate with the full industrial range of Meech Pulsed DC static elimination equipment. It is light and compact but able to cope with the most technically demanding industrial applications. In addition to the ability to control power output, frequency and polarity, the 977v3 also offers alarm and remote monitoring and control functionality. A new feature of the 977v3 is an 8- way DIN for connection of an ion balance sensor and feedback system. Patent No. ZL200530000278.0
|
|
|
The Model 233v3 Pulsed DC Controller has been designed to operate with the Series 200 range of ionisers for ESD applications. The 233v3 is light, compact and features lockable plug and socket connectors for quick release. It also provides the option of Steady State DC (SSDC) output.
|
|
PS5050 model flashlamp driver is designed for flashlamp-pumped lasers and establishes itself as an updated version of PS5010 driver. PS5050 features microprocessor control and back illuminated LCD display where all output parameters of power supply are conveniently displayed.
Flashlamp driver comprises one or several charging modules, a discharge and simmer module and a control circuit. Such design allows the unit to be operated with the utmost ease and convenience. The unit is fitted into a 19" standard housing and may be comfortably mounted in your power supply stands. The unit is manufactured in conformity with EN61010 and EN55011 standards.
Driver can be remotely controlled through RS-232 and CAN (Controller Area Network) interface.
|
|
Power for the World Market Leader
High power lasers can be used for applications such as cutting, welding and marking. This non-contact method of material processing offers many advantages such as flexibility, high speed and superior quality. Lasers simplify the entire fabrication chain.
TRUMPF, the leading manufacturer of laser systems for material processing in the world, trusts our power supplies.
HÜTTINGER manufactures reliable power supplies for laser excitation in CO2 lasers.
|
|
* 0~60A Continuous Wave Output
* Voltage self-adaptive control, no need of manual setup
* Inside/Outside control
* Inside timer
* With high-stabilization, anti-interference ability
* Over current, over voltage and water cooling system protection
|
|
Applications include:
-Automotive sheet metal and components
-High-speed bi-metal contact welding
-Storage Batteries
-Aircraft components (aluminum and titanium)
-Nut resistance spot welding
-Projection welds
-Motor armature fusing
-Markless welding
The ISA range of Inverter power supplies provides the highest level of control available today in large scale resistance spot welding. All models are intelligently packaged in “NEMA” style enclosures and are designed to deliver robust performance in the harshest of production environments.
|
|
|
|
|
|
Miyachi Europe offers the high end welding system AWS3 with ISQ 20-10K especially for automotive, tooling and electric/electronic industry requiring high end interfacing and high speed automation. The new product expands the weld current range up to 10kA.
Applications:
Automotive: Lead frame welds, connectors, compacting, pumps, motors, coils
Tooling: Burrs, saw blades large
Electric/Electronic: Components (e.g. capacitors, resistors), fuses, motor switches, relays, contacts, electrical motor fusing, magnet wire welding
Technical Specifications:
max current weld head with short secondary cables 2 x 400mm², length 500mm measured = 10kA
Benefits:
+ Compact design like ISQ20-6
+ High duty cycle
+ High output power (250A)
+ External transformer water cooled
+ Interfacing identical to ISQ20-6
+ Full AWS3 functionality
Dimensions (mm):
Inverter: 216 x 420 x 480 (W x D x H)
Transformer: 284 x 110 x 170 (W x D x H)
Weight (in kg): Inverter: 20kg; Transformer: 16kg
Power requirements: 3 x 400VAC, 50/60 Hz, 20kVA
Legal Approvals: CE compliant
|
|
Inverter Power Supply - IS 120
Inverter Power Unit
Controlled DC Inverter for a wide range of applications - Compact device with terminal and remote transformer
Features
External programming panel
Connection to all mian voltages
Indication of all actual values
Status and error detection in clear text
Applications
Well-suited for automation
Maximum quality requirements
Safety critical environment
Materials with very poor welding properties
Use
Economical and efficient operation
Stable processing and high reproducibility
High grade of weld
Integrated process monitoring
Optimum quality documentation
|
|
Inverter type power supply for spot welding (resistance)
Average rate 1000 - 2000 Hz
18 to 72 KA standard - Parallel to strong currents
QUALITY - PERFORMANCE
- Provision of energy very quickly
- Time welding reduced
- Low projection area
- High quality welding
- Increased speed welding
- Ideally suited for hard coating materials
- Welding of non-ferrous materials (aluminum - copper - brass - etc ...)
- High reproductibility of welding points
- Loop and exhibit no influence on the welding
- Ease of integration transformer welding weight and small size (board)
ECONOMY
- Performance (70%)
- Reduction of energy consumption
- Reduced infrastructure costs
- Need cooling reduced
- Low wear electrodes
CONTROLLER FOR THE RESISTANCE WELDING
|
|
|
|
see the results for the following category : 
