|
|
Nor-Cal offers an extensive selection of commonly used quartz crystal feedthroughs, sensors and multi-channel monitors, cables, quartz crystals, accessories and replacement parts for use in semiconductor, optical and industrial thermal deposition processes. Custom feedthroughs are available with a variety of flanges in all sizes.
Our coating instrumentation products support one of the more popular methods of thin film measurement and rate control _ the crystal monitor, which utilizes the piezoelectric properties of a quartz crystal.
The electrical characteristics of the crystal, which is held in place by the sensor, change during deposition. Single sensors are generally used for short deposition runs, whereas, dual sensors allow for longer runs. Dual sensors require an airline to operate a pneumatic shutter which covers one crystal at a time. The sensor is either welded to the feedthrough or attached with connectors. Most sensors are available with cooling lines.
The application determines the correct choice of sensor. The sensor determines compatible feedthroughs and cabling. The chamber determines the appropriate feedthrough and flange. For application temps up to 150°C, electrical connection between the sensor and feedthrough is accomplished with a vacuum coaxial cable. A bakeable, one piece sensor/feedthrough replaces the standard in-vac cable with a stainless steel high-temp coaxial line for high temperature applications up to 300°C. |
|
| ... products without technical information |
| |
Thin film coating is a vacuum deposition procedure used to enhance the transmissive properties of an optical surface. The most common types of dielectric coatings are anti-reflection and high reflection coatings, but beam-splitter, band pass filter, edge filter, and polarizing coatings are also available. Because thin film coatings are more durable than optical glass, coatings also help protect an optic surface from scratches and the environment.
Optimax produces optics up to 300mm in diameter with a wide variety of narrow and broadband anti-reflection coatings including doublet interface coatings. Both metal and dielectric mirror coatings are also available. For custom coatings, we utilize TFCalc thin film design software. Please see the reverse side for sample reflectance curves.
Optimax performs test runs of all coatings before beginning production to ensure a good design. We use a Perkin-Elmer Lambda 900 Spectrophotometer to check the performance of the coating upon completion. Adhesion, abrasion, and humidity tests are available to verify coating durability in accordance with sections of MIL-C-675C, MIL-C-48497A, and MIL-C-13508C specifications. Laser damage testing is also available upon customer request. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
American Maplan's Out of Line Vertical, In Line Vertical , High Performance and CalandretteŪ film and sheet systems offer a full range of extrusion solutions
High degree of versatility to suit every line design requirement
Inline systems can be combined with all automatic thermoformers currently available on the market
Our extruders are designed to accommodate a large processing range at high output rates with low energy consumption
Melt degassing for excellent film quality
|
|
| ... products without technical information |
| |
With the RIPACK MULTI-COVERS, you can make your own covers or wraps in different heights and sizes.
Two sealing rods for high quality.
Different sealing widths, manual or pneumatic. |
|
| ... products without technical information |
| |
The Turbopack is a shrink column mounted on a trolley, easily operated by pushing, for quick and uniform shrinking of pallet covers.
Quick : only 60 seconds for one pallet (euro).
Independant and mobile : shrinking operation is possible anywhere in the factory or the shop, thus preventing the movement of unsteady loads for wrapping. |
|
Model 975 Features:
Rugged aluminum body design - weighs only 3.3 lbs.
125,000 BTU
Safety trigger - automatically shuts off gun when released
Cool Combustor even after extensive use
2', 4', & 6' Extensions for shrinking large items
The Benefits of Shrinkfast:
Manufactured in U.S. - parts always available for immediate shipment
Factory reconditioning service available
Full 1 year factory warranty
Authorized Distributors around the world
UL listed
The Benefits of Shrinkwrap:
Protection from weather damage
Cost effective: (only pennies per pallet)
Shrinkfilm is waterproof - stretchwrap is not
Portable & versatile for any size job |
|
The EVAP plus plate-type evaporator is a fully welded heat exchanger without any gaskets. Those areas of sugar factories where such evaporators are used see a substantial improvement of productivity and capacity.
The complete plate pack consists of pressed, roller seam-welded stainless steel plates forming two separate flow chambers, i.e. one tube-shaped and one wave-shaped channel.
EVAP plus %u2013 In use worldwide The low weight and reduced space requirements of GEA Ecoflex plate-type falling-film evaporators open up new possibilities for plant designers and operating companies. Their competitive advantages include not only their higher K values and smaller temperature differences, but also their possible retrofitting into an existing Robert evaporator.
World wide are approx. 100 units, with more than 300,000 mē heat transfer area,
successfully employed - e.g.:
Suiker Unie, NL, 6,000 mē pre-evaporator
Hohenau Evaporator Station, A, 20,000 mē
R.T. Wanze Sugar Factory, B, 39,000 mē
Nordzucker Uelzen, D, the largest single unit with 8,300 mē |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
| ... products without technical information |
| |
CHIP FUSE TF16AT - Chip Current Fuses (Anti Pulse)
- Small and light chip current fuses for the secondary circuit.
- Excellent in anti-pulse characteristics.
- Original construction and manufacturing method stabilize fusing characteristics.
- Able to reduce an occupied area.
-Low power consumption and less voltage dropping due to exceedingly low internal resistance.
- Suitable for overcurrent protection of circuit block in small electronic devices.
- Suitable for both flow and reflow solderings.
- Products meet EU-RoHS requirements |
|
Free Energy Europe manufactures, sells and distributes high quality thin film silicon panels of 5, 7, 14 and 19 Watt, which are all suitable for charging 12 volt batteries. Free Energy Europe panels can power a variety of domestic applications, including lighting, 12V battery charging, phone charging, radio, and TV.
Models:
5 W ; 7 W ; 14 W ; 19 W |
|
These direct print yokes by heat transfer on film meet a need for identification produces upstream or downstream from a machine of conditioning.
Adaptable on existing line, they allow the road repair of texts logos and bar codes.
The range is declined according to 3 models existing each one in 2 widths 53mm and 107mm:
SERIES DPMIII I
Direct print yoke by heat transfer.
Intermittent mode: impression of information during the stop.
Great autonomy of impression (film roller of 450 ml).
SERIES DPMIII C
Direct print yoke by heat transfer.
Continuous mode: impression of information in run.
Great autonomy of impression (film roller of 600 ml).
SERIES DYNACODE
Direct print yoke by heat transfer.
Continuous and intermittent mode: modulate giving to the industrialists a great flexibility in use when the 2 modes are necessary.
Great autonomy of impression (film roller of 900 ml).
All the models are equipped with film heat transfer optimizer.
The resolution is of 300 dpi.
You work as a mode only connected by using the drivers Windows or a graphic software standard LABELSTAR. |
|
|
