|
|
|
|
|
|
VN (OLI® Standard Line) and VNP (OLI® Professional Line) are Electric High Frequency Concrete Vibrators. The VNP Professional Line develops higher centrifugal forces and has a shaft that is equipped with four bearings (plus needle bearing) which makes this line suitable for extra-heavy-duty jobs. Both lines include16 ft protection hose and 33 ft electric cable with CE plug and ABS hand switch.
The strongly increased compaction capacity of the VNP Professional Line results in perfect elimination of air bubbles in the concrete in compliance with modern concrete technology. With 42V/200Hz or 230V/200Hz and six different head diameters the range is suitable for every kind of building site job or for the use in concrete compaction plants (floor manufacturing).
- Complete motor protection through thermistors (VN Standard Line)
- Head diameters: 1-1/2", 2", 2-1/4", 2-1/2", 2-5/8", 2-3/4"
- Amplitude: 0.05" to 0.1"
- Efficiency diameter: 2 ft to 6 ft
- Tip manufactured in steel or Vulkolan
- Head surface hardened
- Low electric input
- High performance
- Two years warranty
|
|
|
Wyco High Cycle Vibrators are manufactured to properly consolidate difficult performance based concrete mix designs. The consistent speed output, under variable loads, produces uniform results. The unique Square Head design ensures that your job will have the quality and production you have come to expect from Wyco.
|
|
|
Our 600 Series Internal Pneumatic Concrete Vibrators are high performance immersion vibrators of simple precision construction. The design features minimum moving parts and no bearings. Each model has an in-line lubricator. There are 8 standard sizes.
|
|
|
The BD Pneumatic Concrete Vibrator series utilizes a built-in pneumatically driven motor which has only two moving parts, the vane and rotor. Compressed air is supplied to the vibrator through the air valve and inner hose. Air flow into the rotor, passes through the passage ways in the vane, back through the "air gap" on the rotor and outer holes in the rear flange. This activates the rotor and the vibrator begins to vibrate
|
|
H.F. ELECTRICAL IMMERSION VIBRATORS
42VOLTS-200HZ-12 000 RPM
EQUIPPED WITH 5M HOSE, SWITCH CASE, 10M CABLE ET FICHE CEE. STEEL OR VULCOLLAN CAP WORKING ON FREQUENCY CHANGER
|
|
Our vibrators represent an optimum solution for the numerous problems arising from the vibration of concrete.
They are available in a wide range on models and satisfy the needs of the big as well as the small companies in terms of a continous and heavy duty or of a saltuary and lighter use.
The housings consist of special steel and have been were subject to a termic tratment against wear due to the abrasion caused by the concrete. The vibrators have an insulation according to IP 67 and are suitable for immersion also with high specific pressures.
|
|
|
FITTED WITH 2 M HOSE, TURN ON-OFF HANDLE, STEEL OR RUBBER MADE HEAD
|
|
| ... products without technical information |
| |
|
|
|
|
VN (OLI® Standard Line) and VNP (OLI® Professional Line) are Electric High Frequency Concrete Vibrators. The VNP Professional Line develops higher centrifugal forces and has a shaft that is equipped with four bearings (plus needle bearing) which makes this line suitable for extra-heavy-duty jobs. Both lines include16 ft protection hose and 33 ft electric cable with CE plug and ABS hand switch.
The strongly increased compaction capacity of the VNP Professional Line results in perfect elimination of air bubbles in the concrete in compliance with modern concrete technology. With 42V/200Hz or 230V/200Hz and six different head diameters the range is suitable for every kind of building site job or for the use in concrete compaction plants (floor manufacturing).
- Complete motor protection through thermistors (VN Standard Line)
- Head diameters: 1-1/2", 2", 2-1/4", 2-1/2", 2-5/8", 2-3/4"
- Amplitude: 0.05" to 0.1"
- Efficiency diameter: 2 ft to 6 ft
- Tip manufactured in steel or Vulkolan
- Head surface hardened
- Low electric input
- High performance
- Two years warranty
|
|
|
Wyco High Cycle Vibrators are manufactured to properly consolidate difficult performance based concrete mix designs. The consistent speed output, under variable loads, produces uniform results. The unique Square Head design ensures that your job will have the quality and production you have come to expect from Wyco.
|
|
|
Our 600 Series Internal Pneumatic Concrete Vibrators are high performance immersion vibrators of simple precision construction. The design features minimum moving parts and no bearings. Each model has an in-line lubricator. There are 8 standard sizes.
|
|
|
The BD Pneumatic Concrete Vibrator series utilizes a built-in pneumatically driven motor which has only two moving parts, the vane and rotor. Compressed air is supplied to the vibrator through the air valve and inner hose. Air flow into the rotor, passes through the passage ways in the vane, back through the "air gap" on the rotor and outer holes in the rear flange. This activates the rotor and the vibrator begins to vibrate
|
|
H.F. ELECTRICAL IMMERSION VIBRATORS
42VOLTS-200HZ-12 000 RPM
EQUIPPED WITH 5M HOSE, SWITCH CASE, 10M CABLE ET FICHE CEE. STEEL OR VULCOLLAN CAP WORKING ON FREQUENCY CHANGER
|
|
Our vibrators represent an optimum solution for the numerous problems arising from the vibration of concrete.
They are available in a wide range on models and satisfy the needs of the big as well as the small companies in terms of a continous and heavy duty or of a saltuary and lighter use.
The housings consist of special steel and have been were subject to a termic tratment against wear due to the abrasion caused by the concrete. The vibrators have an insulation according to IP 67 and are suitable for immersion also with high specific pressures.
|
|
|
FITTED WITH 2 M HOSE, TURN ON-OFF HANDLE, STEEL OR RUBBER MADE HEAD
|
|
| ... products without technical information |
| |
|
|
