|
|
Transmitters, Transceivers, and Transponders for Datacom and Telecom Applications
Finisar's broad product selection and innovative technology have made us the optical module manufacturer of choice for all major networking equipment vendors worldwide. We have taken a lead role in transforming the telecommunications equipment market from utilizing discrete optical components to leveraging the design and pay-as-you-grow flexibility offered by pluggable modules. Our products are fully compliant with Gigabit Ethernet, Fibre Channel, and SONET/SDH standards and operate at data rates up to 40 Gb/s and for distances greater than 200 km. They feature outstanding performance over extended voltage and temperature ranges, while minimizing jitter, electromagnetic interference (EMI) and power dissipation.
Finisar's Patented Digital Diagnostics
Finisar's XFP, XPAK, X2, 300-pin, SFP, SFP+, 2x6, 2x7, and 2x10 SFF and selected GBIC transceivers feature a microprocessor and diagnostics interface that provides performance information on the data link. Users can remotely monitor - in real time - received optical power, transmitted optical power, laser bias current, transceiver input voltage and transceiver temperature of any transceiver in the network. These digital diagnostic functions provide network managers with a highly accurate, cost-effective tool for implementing reliable performing monitoring.
|
|
Communicate up to 15 kilometers with EIA-232 port-powered transceivers. Flexible, Long-Range Fiber-Optic Communication - Send serial data up to 15 kilometers (9 miles) using multi-mode optical fiber with standard ST connectors. Use data rates from 0-40,000 bits per second.
Easy Application - Plug transceiver/modem directly onto a standard 9-pin serial connector (DB-9). No special mounting is required. Receives power from the host device via the connector; no separate power supply or power wiring is needed. Order transceivers/modems with male or female DB-9 connectors. Use switch to select DCE or DTE standard pin configurations, and eliminate the need for adapters. Transmits continuous light pulses, for simpler testing with an optical meter. Apply with ST pre-terminated fiber cables. Secure and Reliable Data Transfer -
Maximum bit error rate (BER) of 10-9. Far less susceptible to EMI/RFI than copper links. Vertical Cavity Surface Emitting Laser (VCSEL) technology provides component isolation and low power consumption.
|
|
Long distance UART TTL Module
This module enables a two-way digital link up to a range of 6000m.
Available in the 869MHz or 902/928MHz in FHSS (Frequency Hopping Spread Spectrum) bands, these pre-certified module-modems usable without a licence can be qualified in compliance with the RTTE European Directive EN 300-220 / EN 300-489 and the FCC Part 15.247 American standard.
It is considered as a complete radio solution which integrates a digital radio transceiver, a microcontroller, a dedicated firmware.
Data transmission is performed via a UART serial interface.
Its easy integration even for non RF specialists, allowing a high reduction of technologic risks and costs and a Time to market optimization.
It covers most applications requiring long-distance communication, automatic watering control system, long distance GPS data transmission, yachting autopilot, fireworks launching system, modular remote control system, modular radio
telemetry system …and more generally all types of applications requiring long range or in particular disturbed environment.
DemoKit - Integration kit including : demoboard, module, RS232 cable, power supply available for this product.
* Evaluate the products
* Perform RF measurements
* Develop a prototype
For any information http://www.adeunis-rf.com or +33 (0) 4 76 92 07 77
|
|
The narrow band Radiometrix NiM2 transceiver offers a low power, reliable data link in a Radiometrix transceiver standard pin out and footprint.
This makes the NiM2 ideally suited to those low power applications where existing single frequency wideband UHF modules have insufficient range.
Available for licence-exempt operation in the 433MHz EU band, the NiM2 modules combine effective screening with internal filtering to minimise spurious radiation and susceptibility thereby ensuring EMC compliance. They can be used in existing low data rate (<10kbps) applications where the operating range of the system using wide band transceivers need to be extended.
Because of their small size and low power consumption, NiM2 is ideal for use in battery-powered portable applications.
Features
- Conforms to EN 300 220-3 and EN 301 489-3 (10mW version only)
- Standard frequency: 434.65 and 434.075MHz
- Custom frequencies available in 433MHz (EU) band
- Usable range over 500m
- 25kHz Channel spacing
- Feature-rich interface (RSSI, analogue and digital baseband)
- Longer range compared to Wide Band FM modules
|
|
FC-201/VB Audio/Data RF module
Application:
Short distance POS system
Wireless sensor data collecting
Wireless meter reading
Industrial remote control and telemetry
Automatic data collecting system
Building automation, safety and security, powerhouse equipment wireless monitor, entrance control system
Wireless keyboard, mouse
Specifications:
1) Carrier frequency: VHF / UHF
2) Channels: 8
3) FSK
4) Channel Spacing: 25kHz / 12.5kHz
5) RF Power: 20mW
6) Receiving sensitivity: -116dBm
6) Transmitting current: 35mA
7) Receiving current: 25mA
8) Standby current: 5mA
9) Interface: UART / TTL; data rate: 1,200bps; format: 8E1
10) Air data rate: 1,200bps
11) Power supply: DC 5.0V20%
12) Temperature: -25C ~ +70C
13) Dimensions: 37 x 30 x 13mm
14) Weight: 30g
|
|
These modules enable an economic single-way AM/FM digital link over a range of 4km.
They are used as an asynchronous serial channel where the useful data rate ranges from 0.5 10Kbps Manchester.
These modules (miniature daughter board to be integrated) are available in 3 versions
* 433/434MHz – 10mW
* 869.525MHz – 25mW et
* 869.525MHz – 500mW
They are in accordance with the European Directive EN 300-220 / EN 301-489
The applications covered range from radio remote control of gates, roller blinds, point to point transmission, micro-networks ... in general public or tertiary sectors of activity, home automation, access control, alarm ...
They also can be useful in all applications requiring long range or in a particular disturbed environment.
For any information : http://www.adeunis-rf.com or +33 (0) 4 76 92 07 77
|
|
Power OutputF100mw (default),(5/10/15/20dBm Optional)
RF Line-of-sight RangeF 2000m@1200bps,1200m@9600bps
RF Effective RateF 1200/2400/4800/9600bps
Space ChannelF 150KHz
Bandwidth: 12.5~50KHz
Receiver Sensitivity: 123dBm@1200bps-116dBm@9600bps
Supply Voltage :4.75~5.25VDC
Transmit Current: <50mA@10dbm,<80mA@14dbm,<100mA@20dbm
Receive Current: <45mA
Sleep current: <5A
Frequency Band: 405~440MHZ (UAN433) customized
440~470MHZ (UAN450) customized
480~510MHZ (UAN490) customized
850~880MHZ (UAN868) customized
900~930MHZ (UAN915) customized
Channel: 128, Soft Setup
Interface: TTL/UART
Size: 47mm~26mm~6.85mm (excluding antenna base)
Weight: 22g
Antenna Base:50Ohm , SMA
Operating Temperature: Industrial:-35~+80(TCXO)
Commercial:-20~+60
Frequency Stability: }2.5ppm Industrial
}5ppm Commercial
|
|
- LOGICAL I/O TRANSFERS :
Transmitter : 8 logic inputs
Receiver : 8 static outputs or 4 relay outputs (it is possible to have 2 pcs
4 relay receivers + 1 transmitter working together)
Permanent or momentary radio link
7 groups of 3 frequencies (for the version with "high immunity to
interferences") or 8 frequencies
Range : 300 m (in unobstructed area)
Response time : 100 ms
Power supply : 10 to 30 Vdc
Relay output receivers : 12 to 30 Vdc
Metal housing
IP 65
- ANALOGUE I/O TRANSFERS :
Transmitter : 4 inputs in 8 bit resolution or 3 inputs in 10 bit resolution
Receiver : 4 outputs in 8 bit resolution or 3 outputs in 10 bits, static PNP,
4-20 mA/0-5 V compatible.
Permanent radio link
7 groups of 3 frequencies (for the version with "high immunity to
interferences") or 8 frequencies
Range : 300 m (in unobstructed area)
Maximum frequency of use : 3 Hz
Power supply : 10 to 30 Vdc
Metal housing
IP 65
|
|
The Radiometrix UHX1 is a high-specification telemetry radio tranceiver.
The Narrow Band FM multi-channel VHF transceiver unit ideal for use in the new 169.4-169.475MHz European band. Squeezed into a compact, low profile package (67x30x12mm), it can provide a reliable data link capable of supporting rates of up to 5kbit/s or 1200 baud modem link over a range of more than 1km.
The dual frequency capability allows UHX1's transmitter section to be operated on one frequency while receiver frequency on another.
Features
-Conforms to ETSI EN 300 220-3 and EN 301 489-3
-High performance double superhet, 128 channel PLL synthesizer
-500mW RF power output: adjustable via serial command
-Data rates up to 5 kbps for standard module
-Usable range over 1km
-Feature-rich interface (RSSI, analogue and digital baseband)
-Incorporates a 1200baud modem
-Re-programmable via RS232 interface
-Low power requirements
Applications
- Heavy vehicle/machine remote controls
- Environmental monitoring equipment
- Automatic Meter Reading (AMR)
- Asset Tracking and Tracing
- Data logging systems
- Industrial telemetry/telecommand
- High-end security/fire alarms.
Technical specifications
Operating frequency: Any 2MHz segmnet in 140- 175MHz
128 channels controlled via RS232 interface
16 channels selected by parallel interface
Transmit power: : 500mW (+27dBm) nominal. Adjustable 1 - 500mW
Supply range: 5V regulated transmit, 3.1 - 15V receive
Current consumption: 330mA (at 500mW output) transmit, 25mA receive
Receiver sensitivity: -118dBm (for 12 dB SINAD)
|
|
ISM Wireless USB RF data Radio FC-211SU
Features:
1) AT86RF211S based design
2) Comply with CE
3) Weatherproof & exquisite housing
4) Standard RS-232 & USB interface availble
5) Industrial design for various data transmission application
Technical Specifications
Frequency range: 433.92 MHz
Modulation mode: FSK
Channels: 8
Receiving sensitivity: ≤-113dBm
1st IF: 10.7MHz
2nd IF: 455KHz
Adjacent channel selectivity: ≥65dB
Adjacent channel power: ≥65dB
Output Power: ≤10mW （20mW）
Frequency Stability:5ppm
Channel Spacing: 50KHz
Frequency deviation: ≤1KHz
Spurious rejections: ≥60dB
Maximum current: ≤82mA
Stand-by current: ≤14mA
Antenna impedance: 50Ώ
DC Voltage range: 5.00.5 V
Ambient temperature: -20℃～55℃
|
|
This system enables two-way half duplex digital links over a range of up to 6Km.
It is used as an asynchronous serial channel where the useful data rate ranges from 0.2 kBps to 50 kBps Manchester.
These systems offer 9 transmission channels
These modules (miniature daughter boards to be integrated) are available in 4 versions
* Monochannel 433MHz / 868MHz or 915MHz
* 8 channels 433MHz - 10mW
* 9 channels 868MHz
* 1/2/5 channels 868MHz - 500mW for long range applications
They are in accordance with the European Directive EN 300-220 / EN 301-489
The applications covered range from point to point transmissions, industrial remote controls, remote sensors to cordless local networks... in both industrial sectors of activity: robotics, remote control, and in general public or tertiary fields: access control, home automation...
For any information : http://www.adeunis-rf.com or +33 (0) 4 76 92 07 77
|
|
Channel programmable transceiver
The UHF FM narrow band transceiver module STD-302N/N-R is suitable for industrial remote control and telemetry applications. Custom made SAW filters and narrow band technology provides reliable data communication in industrial applications where good interference rejection and practical range is required. Suitable for feedback systems.
|
|
869MHz Wide Band FM Radio Transceiver
The BiM3B radio transceiver module is an enhanced higher power replacement for the European version BiM3A-869-64.
Two frequency variants are available in the European unlicensed band, one with 5mW RF power with no duty cycle restriction, the other with 25mW RF power with 1% duty cycle restriction.
Features
- Complies with European harmonised standards EN 300 220 and EN 301 489
- RF power output: +14dBm (25mW)
- Data rates up to 64kbps
- Crystal controlled PLL FM circuitry for both Tx and Rx
- Receiver Sensitivity: -101dBm for 1ppm BER (64kbps)
- Usable range up to 300 metres external, 75 metres in building
- RSSI (standard) or carrier detect option
- Analogue and digital baseband
- Low profile with small footprint
|
|
RF Radio Transceiver FC-211AG
Main Specifictation :
1)ADF7020-1 based design, with less peripheral circuit, high reliability.
2)The communication data rate can reach 38.400Kbps.
3)TTL/UART, RS-232, RS-485 available to provide transparent data interface.
4)Transparent data transmission and intelligent data control.
5)Low power consumption and sleep function, capable of awaking up passively by air signal.
6)Industrial standard design with low cost.
Specifications
1)Frequency Range: 474.80475.50 MHz (80-650MHz available based on customers needs)
2)Frequency Stability: 5ppm
3)Channel Capacity: 8 (customization for more channels)
4)Channel Spacing: 50kHz
5)Modulation Mode : FSK
6)Communication Data Rate: 1.2Kbps~38.4Kbps
7)Interface Available: UART/TTL, RS-232, RS-485
8)Receiving sensitivity: -114dBm
9)Interface Data Rate: 1.2Kbps~38.4Kbps
10)Power Output: 50mW
11)Power Supply: DC 5.00.5V
12)Sleep Current: < 3uA /TTL,< 0.5mA /RS485,< 3mA /RS232
13)Transmitting Current: < 40mA /TTL,< 51mA /RS485,< 52mA /RS232
14)Receiving Current: < 30mA /TTL,< 36mA /RS485,< 36mA /RS232
15)Dimensions(L x W x H): 40mm25mm10mm
16)Weight: 10g(antenna excluded)
17)Operating Temperature: -25C ~ 60C
18)Antenna Impedance: 50
19)Antenna Port : SMA connector, female
|
|
Micropower Data RF Module FC-211/SP
Application:
Wireless data transmission.
Wireless meter reading
Automatic data collecting system
Industrial remote control and remote measurement
Building automation, safety and security, powerhouse equipment wireless monitor, entrance control system
Specifications:
1) Carrier frequency: 433MHz
2) FSK
3) Channel: 4, customization for more channels
4) Power: <40mW
5) Receiving sensibility: -107dBm
6) Sleep current: <0.2mA/TTL, <0.3mA/RS485, <3 mA/RS232
7) Transmitting current: <80mA/TTL, <80mA/RS485, <85 mA/RS232
8) Receiving current: <13mA/TTL, <13mA/RS485, <16 mA/RS232
9) Interface: TTL, RS-232, RS-485, data rate: 1,200~19,200bps,
format: 8E1/8N1/8O1 user-defined
10) Air data rate: 1,200~19,200bps
11) Voltage: DC 5.0}0.5V
12) Temperature: -25C ~ 60C
13) Size: 45 x 30 x 10mm
|
|
Frequency band: VHF/UHF, default band: 220MHz
Modulation : 3FSK
Channel spacing: 5KHz12.5KHz18.75KHz and 25KHz optional.
Interface RS-232,RS-485 and TTL optional.
RF Data Rate: 1200bps,2400bps,4800bps,9600bps,19200bps optional.
Power supply :+10.5V --+15.0V,Nominal voltage +13.8V
Standby current :≤80MA
RX current :≤100 MA
TX current :≤1.6A
Operating temperature : -40+85
Channel spacing :5KHZ
Modulation : 3FSK
RF output power :5.5W0.5W
Frequency deviation :500HZ
Spurious Emissions (Radiated) : ≤-65 dB
RX sensitivity : ≤-118dBm1200bps.
|
|
General description
The ZL60301 is a very high-speed transceiver for parallel fiber applications. This transceiver performs E/O and O/E conversions for data transmission over multimode fiber ribbon. The transmit section converts parallel electrical input signals via a laser driver and a VCSEL array into parallel optical output signals at a wavelength of 850 nm. The receive section converts parallel optical input signals via a PIN photodiode array and a transimpedance and limiting amplifier, into electrical output signals.
The module is fitted with a pluggable industry-standard MegArray BGA connector. This provides ease of assembly on the host board and enables provisioning of bandwidth on demand.
|
|
Functional principle:
The PLICSRADIO series is used for easy wireless transmission of4 ... 20mA/HARTsignals andswitchingconditions. An emitting unit receives the measured values and can be also used as (Ex) supply for sensors connected via cable. Individual 4 ... 20 mA/ HART sensors of any manufacturer can be connected. A receiving unit receives the measured values via a radio link and transfers these to a 4...20mA output or a processing unit, depending on the version. In addition, an indicating unit located within the radio range can show the requested measured values.
|
|
ADI offers a variety of transceivers for wireless applications. The Othello family of direct conversion radios offers numerous benefits to developers of GSM, GPRS and EDGE terminals such as best-in-class performance and significant BOM savings. The ADF702x family is well-suited for audio, cordless phones, video over ISM, low-rate connectivity, security systems and automatic meter reading, featuring low power and minimal external components. In addition to the Orthello family, ADI also offers the WiMAX family of RF transceivers which offer a complete RF and mixed-signal system on a chip.
|
|
|
High-frequency SiGe, BiCMOS, and bipolar processes make Maxim your source for low-power, low-cost, high-performance, complete system solution RF ICs for wireless, RF, and cable applications.
|
|
General description :
The ZL20200 is a fully integrated transceiver for dual band IS136/AMPS handsets. The IF input to the receive path is amplified and down-converted to baseband I and Q signals. Gain control is provided. Baseband filtering is also included. A FM demodulator is also provided to support AMPS operation.
The transmit path consists of a quadrature modulator, gain control at IF and up-conversion to RF. Dual band RF outputs are provided. The transmit output stages can be programmed to optimize performance and current consumption.
ZL20200 also includes a fractional N RF synthesizer and two IF synthesizers to provide all local oscillator signals required. Flexible programming is provided via a 3 wire serial bus. Additional control pins allow accurate timing control when switching between modes
|
|
RF Data transceivers, RF Radio transceivers, Radio modem ideal for telemetry, home automation, remote meter reading.
High sensitivity and high speed data transceivers, micro embedded transceiver, single channel radio modem.
AUREL RF receivers are produced in accordance to RoHS European Directive and are identified with a -G- suffix to Manufacturing Code (Ex. 650200609G).
|
|
Features :
- Laser Class 1
- Compliant with Small form Factor Pluggable MSA Specification
- Compact Size (13.3 x 49.8 x 9.8 mm / 0.52 x 1.95 x 0.39")
- Compliant with Industry Standard RFT Electrical Connector and Cage
- Available with either button release or bail release latching mechanism
- High-Performance and Cost-Effective
- Single +3.3 V Power Supply and TTL Logic Interface
- Low Power Consumption
- Metal Package for Superior EMI Performance
- EEPROM with Serial ID Functionality
- Enhanced Monitoring Functionality (Digital Diagnostics per SFF-8472 available)
- Standard and Wide Operating Temperature Ranges
Applications:
- SONET/SDH from 155 Mbit/s to 2.7 Gbit/s (OC-48, OC-12, OC-3, and STM-14, STM-4, STM-1)
- GbE (GbE-SX, GbE-LX, and GbE-ZX)
- FC (1GFC and 2GFC)
- Transmission distances from 500 m to 100 km
- Metropolitan and access systems
- IP routers and ATM core switches
- DWDM for Metro Area Networks
|
|
|
Designers can easily add cost-effective, short-range wireless data features to their products using the Toshiba family of low-power, high-sensitivity, single-chip radio transceivers and receivers. The devices offer frequency bands of 240 to 450 MHz, 900 MHz and 2.4 GHz. Each device is engineered to enable flexible and customized system designs reducing end-product and manufacturing costs.
|
|
DESCRIPTION
The use of plastic optical fiber (POF) as a physical layer for 1394b (FireWire) is on the rise. Firecomms' FDK300S-101 Optical 1394b Transceiver Evaluation Kit allows the user to examine a data link over POF and to test the operation of the fiber optic transceivers.
This evaluation kit includes two evaluation boards, two multi-region DC power supplies and a 10 meter Step Index POF cable with SMI plugs at each end. Each board includes a Tx-Rx pair in an SMI socket. A CD
containing the data sheets and full design files for the PCB also is included.
The PCBs have been carefully laid out and tested to demonstrate the performance of the Firecomms 1394b Transceiver FDL300E/D over POF.
Each evaluation board carries the POF transceiver components in a through-hole SMI or IDB-1394 socket.
The electrical input and output lines from the transceiver are brought out to SMA connectors. The input accepts an LVDS/CML or PECL data source such as a Bit Error Rate Tester (BERT), Pattern Generator, or other signal source.
|
|
JDSU integrated fiber-optic transceivers provide a high speed serial electrical interface for connecting processors, switches, and peripherals using fiber optic technology. The 1 - 10 Gb/s serial optical converters are designed for the increased densities, higher performance, and lower power consumption required in high data rate network environments and applications. Those applications include gigabit Ethernet and Fibre Channel applications: storage networks to HBAs, backbone networks/LANs to NAS-as well as client/server environments, distributed multiprocessing, and data acquisition.
|
|
FEATURES
- Compliant with MOST optical physical layer specification revision 1.1 over an operating temperature range of -40C to 95C
- Enables an optical budget of 21 dB, an improvement of 8 dB over the MOST physical layer specification revision 1.1
- Transmitter high-speed RCLED source provides high optical power with lower operating current and fast rising and falling optical edges
- Stable "sleep mode" operation with exceptionally low current consumption of only 10 A.
- RoHS compliant
|
|
|
The 622Mbps transceiver series products from HTOE are high performance, cost effective modules for serial optical data communication applications specified for a singlemode of 622 Mb/s. These modules are intended for Single-mode fiber, operate at a nominal wavelength of 1310nm and complies with the industry standard 19 footprint. Each module | | |
