|
|
Characteristics
Absolute measuring system with sensor retaining carriage.
Type LT-S
Measuring range 140 - 3040 mm
Resolution (max.) programmable 0,1 µm
Accuracy (typ.) +/- 5µm
Characteristics
Compact absolute measuring system with rod to push.
Type LT-G
Measuring range 60, 100 mm
Resolution (max.) programmable 0,1 µm
Accuracy (typ.) +/- 5µm
Characteristics
Solid absolute measuring system with rod to push.
Type LT-PI
Measuring range 100, 200 mm
Resolution (max.) programmable 0,1 µm
Accuracy (typ.) +/- 5µm |
|
Company COMPAUT offers a broad range of rules and meters of quality.
The majority of this whole of visualization can be delivered in 24:00
Among these rules, many models are perfectly compatible, as well mechanically as electrically, with the principal standards of the market.
You can thus come to replace those which you usually use, without same having to change the connectors, the whole for a price without comparison.
In addition, company COMPAUT points out that it carries out in its workshops the repair of the meters and the rules, some is the mark, and this within very short times.
N’ thus do not hesitate to entrust to us your defective products for a free estimate. |
|
Highest quality in most compact form, that is that
SENC 50 of ACU RITE.
The small dimensions and the high accuracies of this taper roller bearingled top illumination measuring system are ideal conditions for the employment in the measuring technique.
* Compact dimensions
* Dissolutions of 0,5 µm to 5 µm
* TTL and similar signals
* Measuring lengths from 50 mm to 525 mm
* Coded reference marks -
Position Trac
|
|
The POSIMAG length measuring system comprises an MR scanning head and a magnetic dimensional scale. The position is determined without contact and thus without wear or tear. This measuring setup supports resolutions in the µm range.
POSIMAG is suitable for linear, angluar and speed measurements.
Technical advantages:
Sturdy construction, contact-free and wear-free, shielded metal housing, protection category up to IP67, signal processing as standard with encoders, distance between the MR sensor head and the magentic strip up to 2 mm, measuring lengths of up to 30,000 mm.
Thanks to its special properties, POSIMAG is ideal for many industrial applications in the production of machinery, plants and precision equipment as well as research. For example: Metal and wood processing, manual tasks in handling systems, positional checks for linear units, quality-control systems for sheet metal, punches and presses.
|
|
RAVAS supplies a complete range of scales for mounting on forklift trucks.
RCS system
For simple check weighing, where a high accuracy is not required, there is the RCS hydraulic load indication system. With the RCS an oil pressure sensor is installed onto the hydraulic circuit of the forklift by means of a T-coupling. The indicator in the cabin translates the measurement into a weight indication of the load on the forks. The RCS has a limited accuracy, with a possible error of maximum 2% of the lifting capacity of the truck.
The system is meant for simple check weighing, such as the checking of incoming goods, and for avoiding the overloading of lorries, warehouse racking and the forklift truck itself.
RCS PLUS system
The RCS PLUS is an accurate hydraulic weighing system for forklift trucks. On a forklift truck with a capacity of 2.500 kg the weight graduation is displayed in steps of 2 kg, with a 5 kg tolerance (+/- 0.2%). The RCS PLUS weighs by measuring the pressure in the hydraulic lifting system of the forklift truck, via a temperature compensated sensor on a valve block.
During a controlled descent of the mast the pressure in the hydraulic system is measured repeatedly, the software translates these measurements into an accurate weight indication of the load on the forks.
|
|
Fleet Weigh is an all in one digital Weight Gauge, Pre-Start Checklist, Card Access and Speed Alert module - designed to provide lift truck dealers with commonly requested safety features all in the one package.
Fleet Weigh provides the lift truck industry with a no-nonsense approach to load weighing and routine safety, price competitive with any digital weight gauge on the market. |
|
Built tough for the lift truck industry, Fleet Weigh is a rugged, fully immersible unit, (wash down friendly), with no easily broken plugs or wires.
Installation of Fleet Weigh is straight forward for a lift truck mechanic with basic electrical skills. It is installed without the use of laptops or other 'breakables'.
Operator and maintenance friendly - Fleet Weigh is a straight forward retro-fit to most industrial moving plant. |
|
The RWV Autonome RF is a set of weighing forks with high accuracy (maximum error 0.1% of the lifted load). The RWV Autonome RF combines the strong points of the RWV Autonome (functioning independently from the truck, simple installation) with the advantage of an indicator within reach in the cabin of the truck.
By pushing a button, net weights can be measured, or the weights of several pallets can be added up to a total weight per shipment. A printer can also be installed, for printing the weight data on a ticket. Signal transfer from weighing forks to indicator is by wireless (Bluetooth) connection.
|
|
Responding to the lift truck industry's request for a simple and economical lift truck on-board check weighing /overload safety readout that can be used in any material handling operation and will operate in severe working environment.
The ED2-Series SkidWeigh is the only forklift on-board check weighing system that is found to be installed in multiple quantities within the same company.
- Low installed cost
- Virtually maintenance free
- No operator training required
- Fully automatic
- Simple calibration with known load weight
- Operating voltage from 12 to 55 V DC
- Can be moved from one vehicle to another
- Will not reduce lift truck lift capacity
- Can be installed by a local lift truck service technician or the end user mechanic
- Resistant to industrial environments
- Field serviceable
- Wide range, check weighing capacity up to 50000 kg or lbs.
- Operating temperature ranging from -40°C to +85°C (-40 to 185° F)
- Accurate to /- .5 to 1% of vehicle lift capacity
- On-board printer capability, optional
- Accumulative weights capability, optional
- Overload strobe light warning, optional
- Dual weighing channel capability, optional |
|
Mobile Weight Cart
- Small and compact electronics specially developed fo mobile wighing.
- Highest level of water and humidity resistance.
- Smaller housing is more robust and withstands impacts and vibration better.
- One electornic board without connectors means reliability for many years in the hardest applications.
- Lower weight of the scale is self;122kg,means easier handling of the scale.
- More reliability for the hardest applications and environments.
- Lower power consumptions makes scale more user friendly.New batteries are only needed one time per year when weighting 10 pallets per day.
- 4penlight batteries can be changed without any effort.
- Auto shut off prevents the batteries to be discharged when client forgets to trun the in dicator off.
- Summation of weights with sequence numberallows verification if the total load has been weighed. |
|
| ... products without technical information |
| |
RAVAS supplies a complete range of scales for mounting on forklift trucks.
RCS system
For simple check weighing, where a high accuracy is not required, there is the RCS hydraulic load indication system. With the RCS an oil pressure sensor is installed onto the hydraulic circuit of the forklift by means of a T-coupling. The indicator in the cabin translates the measurement into a weight indication of the load on the forks. The RCS has a limited accuracy, with a possible error of maximum 2% of the lifting capacity of the truck.
The system is meant for simple check weighing, such as the checking of incoming goods, and for avoiding the overloading of lorries, warehouse racking and the forklift truck itself.
RCS PLUS system
The RCS PLUS is an accurate hydraulic weighing system for forklift trucks. On a forklift truck with a capacity of 2.500 kg the weight graduation is displayed in steps of 2 kg, with a 5 kg tolerance (+/- 0.2%). The RCS PLUS weighs by measuring the pressure in the hydraulic lifting system of the forklift truck, via a temperature compensated sensor on a valve block.
During a controlled descent of the mast the pressure in the hydraulic system is measured repeatedly, the software translates these measurements into an accurate weight indication of the load on the forks.
|
|
Built tough for the lift truck industry, Fleet Weigh is a rugged, fully immersible unit, (wash down friendly), with no easily broken plugs or wires.
Installation of Fleet Weigh is straight forward for a lift truck mechanic with basic electrical skills. It is installed without the use of laptops or other 'breakables'.
Operator and maintenance friendly - Fleet Weigh is a straight forward retro-fit to most industrial moving plant. |
|
The RWV Autonome RF is a set of weighing forks with high accuracy (maximum error 0.1% of the lifted load). The RWV Autonome RF combines the strong points of the RWV Autonome (functioning independently from the truck, simple installation) with the advantage of an indicator within reach in the cabin of the truck.
By pushing a button, net weights can be measured, or the weights of several pallets can be added up to a total weight per shipment. A printer can also be installed, for printing the weight data on a ticket. Signal transfer from weighing forks to indicator is by wireless (Bluetooth) connection.
|
|
Responding to the lift truck industry's request for a simple and economical lift truck on-board check weighing /overload safety readout that can be used in any material handling operation and will operate in severe working environment.
The ED2-Series SkidWeigh is the only forklift on-board check weighing system that is found to be installed in multiple quantities within the same company.
- Low installed cost
- Virtually maintenance free
- No operator training required
- Fully automatic
- Simple calibration with known load weight
- Operating voltage from 12 to 55 V DC
- Can be moved from one vehicle to another
- Will not reduce lift truck lift capacity
- Can be installed by a local lift truck service technician or the end user mechanic
- Resistant to industrial environments
- Field serviceable
- Wide range, check weighing capacity up to 50000 kg or lbs.
- Operating temperature ranging from -40°C to +85°C (-40 to 185° F)
- Accurate to /- .5 to 1% of vehicle lift capacity
- On-board printer capability, optional
- Accumulative weights capability, optional
- Overload strobe light warning, optional
- Dual weighing channel capability, optional |
|
Mobile Weight Cart
- Small and compact electronics specially developed fo mobile wighing.
- Highest level of water and humidity resistance.
- Smaller housing is more robust and withstands impacts and vibration better.
- One electornic board without connectors means reliability for many years in the hardest applications.
- Lower weight of the scale is self;122kg,means easier handling of the scale.
- More reliability for the hardest applications and environments.
- Lower power consumptions makes scale more user friendly.New batteries are only needed one time per year when weighting 10 pallets per day.
- 4penlight batteries can be changed without any effort.
- Auto shut off prevents the batteries to be discharged when client forgets to trun the in dicator off.
- Summation of weights with sequence numberallows verification if the total load has been weighed. |
|
| ... products without technical information |
| |
X-Ray Sensors offer a number of advantages over beta and gamma sensors, including greater precision, better streak detection, long-term stability and non-nuclear technology.
Since the X-ray sensor's energy output can be changed via digital power regulation, it can be optimized to run very efficiently over a wide range of product weights and thicknesses. |
|
Features:
Resolution: 0.1 µm
Linearity: +/- 1 µm (Diameter)
Linearity: +/- 0.5 µm (Position)
Standard gauge fingers for measure of diameters from 5 mm to 90 mm.
Watertight.
Measure of smooth or interrupted surfaces.
Gauge slides driven by air or oil.
Fine adjustment on slide.
Wearproof fulcrums.
Advantages:
Accurate.
Sturdy, suitable for installation on grinders.
Fits pre-, in-, and post-process applications.
Quick set-up and retooling. |
|
Features:
Overall dimension: 20x40x76 mm.
Measuring range: up to 12,5 mm
Repeatability: < 0,05 µm.
Connection to the electronics through cables long up to 30 m
Memory chip for process optimization.
Pneumatic recoil.
Quick manual retooling of the fingers.
Wide range of fixed or manually adjustable supports.
Fingers available with breakaway pin.
Advantages:
COMPATIBILITY
Fits all measurement applications related to:
- diameter
- position
on new or operating machines
No limits of installation due to the loss of the signal.
ACCURACY
Within the measuring range:
- sub micron, through automatic calibration on the master for every measure.
- micron, through automatic calibration on one master only for all measures.
PRODUCTIVITY
No manual retooling within the measuring range.
Quick manual retooling for adjustment to a new family of pieces.
Prevention from machine breakdown due to accidental impacts. |
|
Features:
» Handling of two LVDT transducers, for continuous and interrupted surfaces gauging.
» Compact size.
» Bench and built-in versions.
» Application customisation by the user through the set-up of:
- Gauging formulas;
- Arms ratio for self-learning;
- Metric or British measurement units.
» Analogue indicator for the continuous measurement
display, with x1 and x10 automatic scale change.
» Digital I/O, SINK or SOURCE type, for the connection to CNC/PLC.
» The operator's panel provided with sensitive waterproof sandwich keyboard allows:
- Setting the three gauging thresholds for the output contact;
- Setting the delay of cycle start input contact and zero quota output contact;
- Setting the zero correction value (offset);
- Selection of the reading of individual transducers for the mechanical manual zeroing;
- Measure electronic, manual and automatic zeroing.
» Memory and LEDs test performed at start-up.
Advantages:
» Accurate.
» Simply to configure and to programme.
» Can be integrated in any architecture both in a new machine or in an already operating machine.
» Comfortable to use.
» Tough and reliable.
» Affordable. |
|
|
|