|
|
MATi stands for Metrohm Automated Titration System.
MATi 1 is a fully automated and PC-controlled water analysis system based on the new 836 Titrando and the new 815 Robotic USB Sample Processor XL. In particular, it contains the new quick aliquoting device 6.9958.007, an overflow buret allowing to quickly and precisely dose after the conductivity measurement 100 mL water sample necessary to do pH measurement, alkalinity determination and finally the water hardness titration.
The MATi 1 has all it takes to perform 59 water determinations fully automatically and includes all necessary accessories and sensors. It is a ready-to-use system that fulfills all your requirements:
Full water analysis
Quick aliquoting device
PC-controlled
High sample capacity
|
|
|
|
|
|
Smaller and lighter than our full size 3700 portable, the 3700C uses the same controller. The 3700C will easily pass through an 18-inch diameter or offset manhole.
Bottle choices with the 3700C are more limited than with the full-size model. The bottle options are: 24 polyethylene 500 ml bottles; a single 2.5 gallon (9.5 liter) polyethylene or glass bottle; or a single 2.0 gallon (7.5 liter) ProPak bag with holder. When using the 24-bottle configuration, the 3700C's bottle carrier makes bottle changes fast and easy.
The exclusive LD90 gives you automatic compensation for changes in head height, plus automatic suction line rinsing to prevent cross contamination. The non-contacting liquid sensor is not affected by conductivity, viscosity, temperature, or liquid composition. There are no internal tubing connections, so cleaning and tubing replacement are fast and easy. The 3700 pump outperforms most competing samplers and maintains the EPA-recommended 2 ft/second line velocity at head heights up to 16 feet, with 1/4-inch suction line. For higher lifts, we recommend our 6700 Series.
|
|
All Isco brand portable samplers are built to withstand harsh environments and hard service.
- Vacuum-formed ABS plastic shell withstands exposure and abuse.
- Twin-wall construction with foamed-in-place insulation maximizes structural integrity along with the efficiency of ice used for sample preservation.
- NEMA 4X, 6 (IP67) controller rating for submersible, watertight, dust-tight, and corrosion resistant service.
|
|
Isco developed the first refrigerated sampler designed to be used outdoors without an enclosure, and continues to set the standards for weather and corrosion resistance.
The all-new Isco 4700 Refrigerated Sampler is purpose-built to survive outdoors for wastewater compliance monitoring.
Our 6712FR refrigerator gives you field-proven, trouble-free sample preservation and dependability in harsh environments, along with the most advanced sampler controller available.
|
|
ATI has developed a completely new approach to on-line monitoring of ammonia that is far less expensive and much simpler than conventional monitoring equipment. The Q45N Dissolved Ammonia Monitor uses reaction chemistry that converts ammonia in solution to a stable monochloramine compound equivalent in concentration to the original ammonia level. The chloramine concentration is then measured with a unique amperometric sensor that responds linearly to chloramines while eliminating interference from excess free chlorine in solution.
Q45N monitors are available in two versions, one that includes all components conveniently integrated into a Nema 4X fiberglas enclosure, and a second that separates the monitor from the chemistry system for applications where a more convenient display location is desired. ATI’s Q45N monitoring package for dissolved ammonia provides the measurement stability needed to avoid complicated automatic calibration systems.
|
|
The Tekran® Series 2600 system allows the analysis of ultra-trace levels of total mercury in liquid samples. It offers unparalleled sensitivity and flexibility for those who require truly sensitive total mercury analysis.
Series 2600 is capable of providing a fully automated implementation of the new US EPA Method 1631. This method is capable of measuring waters with a detection limit of much less than the required < 0.5 ng/L (ppt).
Key Features
- Sensitivity measured in parts per quadrillion. Typical MDL: <0.05 ppt
- Atomic Fluorescence based: Greater sensitivity, selectivity and dynamic range than AA based systems
- Unprecedented modularity and flexibility
- Capable of multiple methods:
Direct reading
Single stage gold preconcentration
Dual stage gold preconcentration
- Works with stannous chloride or sodium borohydride reduction
|
|
The PowerMon Titrometer is a versatile applicable on-line measuring instrument. It guarantees a permanent optimal water quality by the continuous supervision in the chemical industry, water and waste water treatment, in power stations and the paper industry.
Advantages
- fully automatic operation
- easy, comfortable operation
- fast data transfer
- precise results
- self-monitoring system
- minimum operating cost by small reagent consumption
- connection of up to 100 external, physical measuring sensors
- remote maintenance and network ability
- update of the operating software or download of data by USB stick
- graphic user interface with interactive Touch Screen operation
- second measuring point without surcharge
- operation also possible without housing
|
|
|
|
|
|
Sievers 900 Portable TOC
The Sievers 900 Portable TOC Analyzer, weighing only 12.5 kg and measuring 35.6 x 22.3 x 46.5 cm, is the first portable TOC analyzer of its kind, bringing the lab to the field. It can be hand-carried anywhere for on-line measurement, used for grab samples, or connected to an autosampler for high volume applications in a laboratory. It requires no external reagents or gas supplies and boasts a four-minute analysis time and a 0.03 to 50 ppb measurement range.
The 900 Portable’s color touch-screen display provides an intuitive menu to quickly establish operating parameters, such as setup and automated calibration procedures, and to graph historical or real-time data. A USB drive enables easy data transfer.The Analyzer was engineered for ease of use and cost-effective operation, requiring no external reagents or gas supplies. It typically needs only a few hours of preventive maintenance annually.
The Sievers 900 Portable won Instrument Business Outlook’s 2005 Gold Award for Best Portable Analytical Instrument Industrial Design.
|
|
The 8930 Includes:
* 900 MAX Portable Sampler Controller (P/N 8972)
* Center Section (P/N 8922)
* Cover (P/N 8890)
Components to complete the system:
* Power Source/Battery Chargers
* Intake Tubing and Strainer
Optional Components:
* Base/Bottle Tray, Composite/Multiple Bottle Accessories
* Pump Tubing
* Factory Installed Options
* Support Software and Data Transfer Unit
* Cables and Interfaces
* Accessories
For pricing, part numbers, and assistance in configuring your Sigma Portable Sampler to fit your application please call Hach: 1-800-227-4224
Sampling for regulatory compliance, monitoring or combined sewer overflows, storm water outfalls, and water quality research may demand a sampler with greater sophistication and capability. If so than the Sigma 900 MAX Controller is what you need.
|
|
Laboratory instrument LabMaster-aw
- High accuracy and repeatability
- Temperature controlled measuring chamber
- Increased measurement speed
- Measurement cell with saved calibration data
- Intuitive and simple menu navigation
- Modular expandability to multi channel system
|
|
|
|
|
|
SEKO introduces the 500 Series family of industrial control instruments designed for measuring:
■ pH
■ Redox
■ Oxigen
■ Conductivity
■ Turbidity
Design compliant with EMI regulations
All instruments comply with the 73/23 EC,89/336 EC,92/31 EC and93/68 EC directives,in order to guarantee maximum Electromagnetic Compatibility.
Serial Communication (RS485)
All instruments are designed for use with RS485 communication serial port,to monitor measurements and data recording.
Graphic Display
The graphic display,with 128x64 pixel resolution,ensures simultaneous display of the chemical measurement,the measurement of the temperature and the status of the various control outputs,by means oficons,throughout the entire process.
Power-assisted adjustment with probeeffectiveness test
The user-friendly software functions are designed to supply fast and effective assistance to the operator.This guarantees excellent calibration results.The system will inform the user about the quality of the electrode in use.
Flexible enclosure design
The enclosure allows various mounting options,such as panel,wall orpole mounting.
Control Functions
The instruments can be supplied with different software functions,ranging from Proportional-Integrated-Derived (PID),Timed and ON/OFF.
|
|
|
For automatic determination, monitoring and LC display of the total residual hardness (water hardness) in the water. The parameter to be measured and the appropriate measuring range are determined by indicator selection and by an appropriate user program. Control via alarm horn, stop solenoid valve or similar devices. Connection provided for recorder and central control station for transmission of analysis results (0/4 - 20 mA output signal), power supply 230 V, 50 Hz with EC type certificate according to guideline 97/23/EC.
|
|
|
|
|
|
VARiON Plus – Ion-selective measurement of Ammonium and Nitrate
with automatic compensation
WTW’s new highly variable ionic sensor VARiON Plus allows:
• The continuous measurement of ammonium and nitrate with dynamic compensation by auxiliary ion-selective potassium or chloride electrodes.
• A further available slot can be used for an additional measuring electrode – this allows to measure ammonium and nitrate with one sensor (2 in 1).
No calibration required! Instead, the sensor comes manufacturer-calibrated and uses long-term stable electrodes.
Low purchase and operating costs! Utmost stability of the electrodes doubles the lifespan of minimizing the operating costs. Additionally, the calibration work and the additional costs for calibration standards is ommitted.
The advantages of the new VARiON Plus system are obvious: This calibration free combination sensor can measure both Ammonium and Nitrate simultaneously. Due to low investment and operating costs, it is a highly cost-effective solution for a reliable 24 hours measurement directly in the process.
|
|
|
|
|
|
Ever more stringent legislative regulations witin the water and wastewater industry are placing increased demands on process orientated system technology. Especially in the wastewater treatment the on-line measurement of Nitrogen and Phosphorus parameters play an important role because of continuous monitoring and optimization of the performance of a biological purification process.
WTW’s answer is the multiparameter system TresCon.
TresCon is a modular analysis system for continuous measurement of analytical parameters like e.g. Ammonium, Nitrite, Nitrate / SAC, total Nitrogene or Phosphate and total Phosphate. This system based on a central controller and one or several autonomous modules is built up on a functional structure which constitutes a "analytical platform" of highest flexibility.
Due to this modularity this system assures a continuous and very reliable operation which constitutes a new dimension with respect to performance, flexibility, reliability and cost efficiency. Additional analyzer modules and parameters are easily accomplished by the user
|
|
Simple! Accurate! Diversified! water analysis with Single Beam UV/VIS Spectrophotometer!
Specifications
Optical System Single Beam
Spectral Band
Pass Width < 1.0nm
Wavelength
Range 190nm ~ 1100nm
Accuracy < ± 0.5nm
Reproducibility < ± 0.1nm
Setting < ± 0.1nm
Slew Rate about 5000nm/min
Scanning Speed Max. 1000nm/min
Photometric
Range -0.1 to 3.0A, 0 to 125%T
Accuracy < 1% at 1A
Reproducibility ± 0.001A
Stray Light 0.05 %T at 220 & 340 nm
Baseline Stability < ± 0.001 ABS/h (at 550nm)
Baseline Flatness < ± 0.001 ABS (200~1000nm)
Noise Level < 0.001A
Drift 0.002A/hr at 340 nm
Monochomater Modified Czerny-turner type With 1200 lines/mm Blazed grating
Light Source Tungsten and Halogen lamp and Deuterium lamp
Lamp Change Wavelength 340nm~410nm (Default 370nm)
Standard Cell Holder Automatic Rotary type 8-position Multi-Cell Holder
Interface Ports RS-232C Serial and Centronics ports
Power Requirement AC 220V, 50/60Hz
Overall
Dimensions(mm) 515(W)x430(D)x242(H)mm
Weight 16kg
|
|
|
”On-site” means measuring Ammonium and Phosphate in the tank. The main advantage is that short sample paths give quick, undistorted results. This is the idea behind the new digital analyser generation from HACH LANGE—AMTAX sc and PHOSPHAX sc. The concept is a practical, logical extension of the proven AMTAX and PHOSPHAX series. It combines all the advantages: the high precision of an analyser and the simplicity of a probe.
|
|
|
|
|
|
Analyzer/station of alarm AQUAPOD SPE
The analyzer/station of alarm AQUAPOD SPE detects and analyzes on line the micropollutions of water.
Thanks to patented technology SPE Box and analysis UV (+ Fluoresence in option) AQUAPOD SPE allows levels of detection lower than the µg/L (ex: 0,06 µg/L in the case of pesticides).
Its just evolutionary database:
- the pesticides (Triazines, derived Diuron, Isoproturon, organophosphates, pyrethrinoid, Ethyl parathion, amides...)
- hydrocarbons (SP 95, SP98, Kerozene, gas oil, oils,...)
- industrial products (Phenols: Chlorophenols, Nitrophenols...)
- complex mixtures (rejections of STEP, liquid manures...)
Aquapod SPE detects also any anomaly of spectrum UV of the eaaux one. Associated with an integrated automatic sampler, it makes it possible to identify new sources of pollution or évévenement
Applications:
- Drinking water: Collectings - Raw waters - treated Water
- Natural Water: Rivers - underground - stoppings
- Cleansing: Rejections of purification plants
- Industry: Water of process
|
|
the AQUAPOD the AQUAPOD LIGHT detects and analyzes a broad range of parameters and pollution in drinking water, water natural, industrial wastes and sea water:
NITRATES
DBO
DCO
COT
MY
UV 254 NM
GENERAL ANOMALIES OF WATER
COLORIMETRY
HYDROCARBONS
URBAN REJECTIONS
COMPLEX INDUSTRIAL PRODUCTS
SPECIFIC PRODUCTS
The AQUAPOD LIGHT integrates an analysis UV and fluorescence (in option) making it possible to reach thresholds of sensitivities about the ppm and Pb
Easy to install, without reagents nor calibration, the AQUAPOD Light ensures you a cost of very low exploitation.
The AQUAPOD LIGHT can accept any type of physico-chemical sensors Modbus RS485, 4 - 20 my...
Moreover, thanks to its exits Modbus, Profibus and Can Open, the AQUAPOD LIGHT can be interfaced quickly towards any system of supervision or communication GPRS or STN
|
|
The Analyst provides far greater accuracy and convenience for water testing. Using the latest advances in microprocessor technology, The Analyst provides a direct-reading, user-friendly analysis system for your choice of 90+ water tests. Most test kits use convenient tablet reagents. Compact, rugged and portable, The Analyst is equally reliable in lab, plant, classroom or field.
Important Features
Choose from OVER 90 pre-standardized important tests
Permanent calibrations for 90+ tests are stored in the memory of The Analyst microprocessor. No standard solutions, calibrations, charts, graphs, or calculations are needed. Procedures manual (supplied) contains all 90+ test instructions. Just read the accurate result directly from the liquid crystal display.
For more information, please visite our website
|
|
Since 1957, the Myron L Company has designed and manufactured highly reliable analytical instruments for a wide variety of applications. Thousands of professionals around the world rely every day on the performance of our instruments. Demanding uses range from boiler water testing to ultrapure water control to medical instruments for artificial kidney machines.
We are proud of the trust our handheld instruments and monitor/controllers have earned in the past. Our product line has evolved to a new level of outstanding performance and value in analytical instruments: the Ultrameter II series. While priced like affordable single-parameter instruments, the Ultrameter II does the job of three, four or even six instruments.
|
|
multiparameter sensor MPS-D8
13 parameters can be measured: water level, °C, conductivity, salinity, O2, pH, ORP, NH3, NO3-, Cl-, NH4+, Na+, Ca2+, F-, K+ and turbidity. For use with data logger MDS-5.
|
|
The PowerMon Kolorimeter is a versatile applicable on-line measuring
instrument. It guarantees a permanent optimal water quality by the
continuous supervision of the legally prescribed limit value for total phosphate and ortho-phosphate in the outlet of municipal and industrial purification plants.
Advantages:
-precise results
-connection of up to 100 external,
-physical measuring sensors
-fully automatic operation
-easy, comfortable operation
-fast data transfer
-self-monitoring system
-remote maintenance and
network ability
-graphic user interface with interactive Touch Screen operation
-update of the operating software or
download of data by USB stick
-minimum operating cost by small reagent consumption
-second measuring point without surcharge
-operation also possible without housing
|
|
|
|
|
|
Leakwise Oil on Water Monitor
Leakwise Oil on Water MonitorLeakwise Oil-on-Water Monitoring and Detection Systems from GE Analytical Instruments provide early, reliable, low maintenance warning of hydrocarbon leaks and spills 24/7 without false alarms. A Leakwise system consists of a wire or wireless signal processor and one of more sensors, depending on the application.
Leakwise oil detection sensors use high frequency electromagnetic energy absorption floating sensors, which enable reliable monitoring of hydrocarbon on water regardless of dirt or oil coating of the sensor or change in water level or water salinity. Advantages include:
%u2022 Provides reliable coverage 24/7 with no false alarms
%u2022 Operates virtually maintenance free for years
%u2022 Detects oil layer thickness (as little as 0.3 mm)
%u2022 Offers an affordable solution for oil leak detection
Applications include oil leak monitoring at refineries, petrochemical plants, pipelines, gas stations, power plants, underground transmission, remote substations, transformer switchyards, marine ports, airports, steel and aluminum manufacturing plants, offshore rigs, groundwater and stormwater runoff, wastewater treatment plants and more.
Leakwise is also an ideal tool for strengthening Spill Prevention Control and Countermeasure (SPCC) plans, as required by the USEPA.
|
|
|
|
|
|
Model 6600 Oil-in-Water Analyzer System
Teledyne's Model 660/661 was the industry standard in oil-in-water analysis for 30 years. The microprocessor based 6600 / 6610 improves upon our proven analog circuitry and the sample handling system. The new, compact modern design incorporates many new features at a significantly reduced cost. Critical features include:
Folded optical system optimized for excellent signal-to-noise ratio and stability
Increased reliability by eliminating many moving parts
New sonicator homogenizes oil (in-line) in water instantly (less than one second)
Improved auto-zero filter system prepares zero fluid for calibration and zeroing without long sparging cycle
Specially developed software with auto calibration features
Automatic self-cleaning sample cell suitable for high pressure and temperature
Manual calibrations done easily with collected zero fluid from sample system using the gravity fed reservoir
Manual or automatic span sensitivity easily checked with internal span flag once field calibrated
Faster response time
Modular design configured to meet specific application requirements
|
|
PE 138
Salient Features & Benefits
- Portable Microprocessor Based, User Friendly & menu Driven.
- Measures directly pH, EMF, Temperature, Electrolyte Conductivity (EC), Total Dissolved Solids (TDS), Dissolved Oxygen (DO) & Salinity, Colorimetric, Abs./%T and Turbidity in Water sample one at a time.
- Unique DO measurement in Air saturated waters using Conventional Polarographic Probe .
- Programmable Calibration upto 3 Points for pH with Memory Back-up .
- Useful for Potentiometric & Redox measurements.
- Automatic/Manual Temperature Compensation.
- Accurate & Highly Stable .
- Elegantly styled into a Brief Case for operational convenience in Field .
- Operates on Rechargeable Battery & Mains Supply .
|
|
BIOTECTOR VACUUM SAMPLER - Water sampling system for analyzers.
Product overview
• Sample container: PVC
• Sample volume: 400ml
• Pinch valve with EMPP tube
• Main sample line 3/8” OD x 1/4” ID
• Automatic fault indication
General Information
The BioTector vacuum sampling system is designed to bring water over a distance of 40 meters with a maximum lift of 6 meters, and to present the sample to the BioTector TOC analyzer, or alternative water analyzer, at ambient pressure.
|
|
|
Automatic measuring and control systems ensure the right water quality in modern water treatment. All required functional elements are mounted on the sampling stations ready for connection. Due to the great variety of our products we are able to supply the appropriate sampling station for each application.
|
|
|
Series of 5 models to measure 8 to 11 parameters; pH conductivity, dissolved oxygen, turbidity, temperature, ORP, Depth, GPS and more.
|
|
|
Oil content analyzer for water or soil applications. This 5 minute test provides an accurate analysis using Horiba's S-316 extraction solvent.
|
|
W-20 Series Water Quality Monitoring System
Product Overview
Water is as precious as life itself. That's why current threats to water supplies make water quality analysis vital to our very existence. HORIBA has created the Multifunction Water Quality Monitoring System. Years of HORIBA sensor technology development have reached their culmination in the form of a 46-mm diameter sensor probe: a compact monitoring solution offering high pressure tolerance, long-term continuous measurement capability and highly accurate, simultaneous analysis of 13 parameters. In addition to the Water Quality Monitoring System's own capabilities, it was designed by HORIBA to be compatible with GPS and other data processing techniques.
|
|
|
|
