|
|
Autokap™1200 Series Single-Head Fully-Automatic filler can fill:
- 3 litre bags at up to 16 bags per minute
- 5 litre bags at up to 14 bags per minute
- 10 litre bags at up to 11 bags per minute
- 20 litre bags at up to 9 bags per minute.
Filler Description
- Autokap™ 1200 is a Single-Head Fully-Automatic bag filler ideal for a large range of fresh or stable liquid products.
- The filler can fill bags from 1.5 to 25 litres in capacity.
- Autokap™1200 is Servo driven and is designed for automatically loading bags into boxes.
- Each filler is specified for the required type of liquid to fill. A large range of fitments is compatible with the Autokap™1200 series.
- Up to four fillers can be installed as integrated pair for high output applications.
|
|
Autokap™1400 Series Single-Head Fully-Automatic filler can fill:
- 3 litre bags at up to 32 bags per minute (16 bags per minute per head)
- 5 litre bags at up to 26 bags per minute (13 bags per minute per head)
- 10 litre bags at up to 22 bags per minute (11 bag per minute per head)
- 20 litre bags at up to 16 bags per minute (8 bag per minute per head)
Filler Description
- Autokap™ 1400 is a Fully-Automatic bag filler ideal for a range of fresh or stable liquid products. It is available both as a single or twin head filler.
- The filler is designed to fill 1.5 to 25 litre bags in capacity.
- Autokap™ 1400 is designed for automatically loading bags into boxes.
- Each filler is designed for the required type of liquid to fill. A large range of fitments is compatible with the Autokap™ 1400 series.
- A box conveyor can be fully integrated to the filler (available as option.)
|
|
Production is dependent on product supply conditions and the dexterity of the operator.
Typical examples of output based on water are the following:
- 1000 litre bags at up to 7 to 12 bags per hour
- 200 litre bags at 20 to 25 bags per hour.
Filler Description
- Autokap™ 1000 is a Single-Head Semi-Automatic Bulk filler that can fill bags ranging from 250 to 1400 litre directly into drums and bins.
- The filler is setup to run a center glanded bag usually supplied in a folded format.
- After loading the bag, the fill head moves to the bottom of the container and rises as the bag fills from the bottom of the container.
- Fillers are specified for the required type of liquid to fill. The Autokap™1000
series is compatible with a large range of fitments.
|
|
|
|
|
|
Sterikap™ 890 Single-Head Semi-Automatic Aseptic filler can fill:
- 5 litre bags at 3 to 4 bags per minute
- 10 litre bags at 2 to 3 bags per minute
- 20 litre bags at 1 to 2 bags per minute
Sterikap™ 820 Single-Head Semi-Automatic Aseptic Filler Extended Shelf Life (ESL) filler can fill:
- 5 litre bags at 5 to 6 bags per minute
- 10 litre bags at 3 to 4 bags per minute
- 20 litre bags at 2 to 3 bags per minute
Filler Description
- The Sterikap™ 800 is a Single-Head Semi-Automatic bag filler ideal for a range of Aseptic and Extended Shelf Life (ESL) products.
- The filler can fill bags from 1.5 to 25 litres in capacity and be fitted with a variety of taps, caps and tubes.
- Sterikap™ 800 is ideal for startup and medium production. Bags are manually loaded into the filler. After filling, they are released for loading into boxes.
- The fill chamber and all product lines are automatically cleaned in place (CIP) after each production run and sterilized in place (SIP) before each run.
- The fill chamber is fully enclosed and sterility is maintained during production with a combination of steam, sterilant water or sterile air.
|
|
Intasept™ 2400 Single-Head Semi Automatic Aseptic filler for the 32mm gland format can fill:
- 5 litre bags at up to 4 bags per minute
- 10 litre bags at up to 3 bags per minute
Filler Description
- The Intasept™ 2400 Single-Head Semi-Automatic Aseptic range can fill bags from 2 to 30-litres in capacity.
- Bags are manually loaded into the filler. After filling, they are released to the rear of the machine for loading into boxes.
- The fill table can be adjusted to allow manual filling of 210 litre bags into drums (available as option).
- Two fillers can be installed as an integrated pair for twin-head operation.
- Intasept™ 2400 is available with 16mm or 32mm fill head. The filler is available in a qualified version for biomedical and pharmaceutical applications.
|
|
With its specially designed distribution nozzle and capping system, this vertical filler is easily and conveniently employed to fill “bag-in-box” containers with food and no-food, low and medium viscosity products. No extra pump is required.
Once filled-up and closed, the bag-in-box container is easily removed through the roller-conveyor.
|
|
| ... products without technical information |
| |
|
|
|
|
A totally new, fully-patented « 3 in 1 » concept, LINEA PACK® PACK offers the following range of functions in one single, exclusive machine unit : a cardboard box shaper, an automatic filling machine and a box sealer incorporating the Hot-Melt system. Extremely compact and space-saving, ideal for fixed or mobile filling lines LINEA PACK® provides a compilation of modern technology offering the opportunity for increased productivity while ensuring the quality of the packaged product.
Scope of application : Wine, fruit juice, water, milk, syrup, alcoholic beverages, soup... LINEA PACK® LINEA can be used to fill vacuum bag containers ranging from 2 to 20 litres Suitable for use with the following tap models: Vitop, Flex-Tap, Press-Tap, Vinitap. Other models as option.
STANDARD EQUIPMENT :
- Filling head which guarantees non-drip filling
- Hydraulic circuit which can be sterilised with hot water, steam or chemicals
- Siemens Touch screen with integrated modem (optional modem card) displaying
the different operating modes : work, maintenance, settings (with « repeat
» function), cleaning,...
- Integrated CIP circuit with liquid outlet for fixed work stations and
automated cleaning of vacuum and nitrogen circuits
- Vacuum monitoring and control : pressure and activation (integrated
anti start-up safety device)
- 360° multi-directional finger retainer plate
- Box shaper with squaring, bottom sealing and pressing functions
- Bag, tap and box detection... with associated alarm signals
- Overlapping flap closure kit as standard on box shaper and sealer
- Bag insertion chute adaptable to all box formats
- Post-insertion bag compacting function...
|
|
A modern, upgradable, automated filling machine, the Premia is ideal for medium and large-scale fiiling of vacuum bags and rigid containers from 2 tp 30 litres. The Premia carries out the following operation completely automaticallty : Begins filling cycle (DAS system) - removes top - removes air from the bag, meters flow and fills bag - nitrogen injection ( if option) - fits top - ejects the filled bag.
TECHNICAL CHARACTERISTICS
Liquid flow rate 82 HL/h
Air pressure 6 bar
Power 1KW
Voltage 220 / 380 V
Frequency 50 / 60 HZ
Air consumption 1 bar
Nitrogen pessure 1 m3/h
GENERAL SPECIFICATIONS
Minimum height in mm 1580
Width in mm 750
Depth in mm 930
Weight in kg 103
|
|
|
|
|
|
|
MTM Power GmbH, the specialist for high quality power supplies, offers in its program DC/DC converters for automotive applications. The series WRC is available with 30, 60, 100 and 150 W. The converters are designed for mobile use acc. to EN 50 155, LES-DB-BN 411 002 and IEC 571-1 (railway, automotive). The battery voltages 24, 36, 72, 90 and 110 V +40/-45 % are covered with three input voltage ranges. All four power ranges have a high efficiency and are available with single or dual output voltages. The converters have an extreme high reliability (MTBF >1.000.000 h, TA = +40 °C) and an isolation of at least 2,1 kVDC (prim.-sec.). The temperature range is -40...+85 °C acc. to EN 50 155. Other important features are resistance against vibrations and reverse polarity protection at the input. The power supplies can be used in 19" racks or for wall mounting with H15 connector. The series WRC needs no ground load, is short circuit protected and has extensive monitoring and protection systems.
|
|
DCS50
Battery powered DC/DC Converters for 19 inch Rack mounting purposes are available from the Huhn-Rohrbacher Power Supply Company. The power range covers 50 to 150 watts.
* 19"-Eurostandard
* EMI Compliant Design
* 3U / 8 HP / 160mm
* Wide Range Input 2:1
* Single Output 50 Watts
* Galvanic Insulation
* CE Sign
|
|
TPCMQ48 DC/DC Converters
1U High, Up to 700 Watts with Integral Hot-Swap Provision
* 48VDC to 12 or 24VDC
* Includes Isolated 5V, ¼A Standby Output
* Hot-Swap Operation
* Wide Range 40 to 60VDC Input
* Integral LED Status Indicators
* I2C Serial Data Bus Option
* Up to 8.8 Watts/Cubic Inch Power Density
* Low Profile: 1.6 Inches (41mm) High
* Single Hot-Swappable Connector
* Reverse Air Flow Option
* Staged Pin Engagement
* ORing Diode on Output
* 1U, 19” Rack Holds 3 Units
* Active Current Sharing
* Optimized Thermal Management
* No Minimum Load
* Control & Monitoring Features
* DC to DC Converter
|
|
DC/DC 19“
Single output 20 - 100 watts
Plug-in Power Supplies for your 19-inch application.
– 19" plug-in module
– Primary/secondary insulation 3000 VAC
– Overvoltage protection
– Output SELV according to EN 60950 and permanent short-circuit proof
– Remote on/off
– Parallel connection possible with load sharing
– EMC Standards EN 50081-1 and EN 50082-2
– VMEbus signals or Power-Fail available upon request
|
|
DC/DC 19“
Multiple output 50 - 70 watts
Plug-in Power Supplies for your 19-inch application.
– 19" plug-in module
– Primary/secondary insulation 3000 VAC
– Overvoltage protection
– Output permanent short-circuit proof
– Ripple at output < 25 mVpp
– Interference emission according to EN 55011 / EN 55022 Class B
– Outputs SELV according to EN 60950
|
|
| ... products without technical information |
| |
|
|
|
|
AirClean Systems PCR Combination Workstation
AirClean®Systems PCR workstations with UVTect™ microprocessor control, allow you to maintain a Class 100 clean work area during PCR preparation. The AC600 Series LFUV Model has a built-in 254 nm ultraviolet light that allows the operator to irradiate tubes, flasks and pipettes between amplifications. The 254 nm ultraviolet light will effectively destroy potentially contaminating DNA and RNA within minutes. UVTect™ monitors the life of the bulb to ensure proper levels of irradiation.
The workstations feature a unique interlocking sash with a safety overlap to prevent gaps. The sash also has a safety switch that automatically turns off the ultraviolet light and activates the blower and fluorescent light when the sash is raised. This revolutionary uni-body design provides unmatched user protection from harmful ultraviolet rays during the sterilization process. HEPA filtered units have a built-in monitoring system to alert the user when to change the HEPA filter.
|
|
BIGNEAT's PCR UV workstation efficiently protects against contamination by bathing PCR aparatus in sterile air and limiting the risk of contamination from the operators arms, or from equipment bought into the otherwise sterile environment.
Powerful UV lamps are combined with optical reflectors to ensure uniform intensity distribution of the sterilising UV radiation.
1. Superb all round vision
2. Electronic filter saturation indicator
3. Quiet operation
SPECIAL BIGNEAT FEATURE: Fan speed increases when door is opened to maintain air velocity to 0.45 m/s at the front access aperture.
Available 800mm wide as PCR UV cabinet, or as a UV sterilisation cabinet (no HEPA filtration)
|
|
POWERFUL UV DECONTAMINATION
The UV lamp insures a full decontamination of the entire work surface, enclosure walls and PCR equipment.
AN ERGONOMY OF QUALITY
The ergonomy of the working apertures is unique. It enables the protection of the handling while allowing the operator to have access to the entire surface of the enclosure.
ENCLOSURE SIZE ADAPTED TO ALL PCR EQUIPMENT
The Biocap™ enclosures have been sized to receive tube racks, pipettes, minicentrifuges and thermocyclers.
PROTECTION OF THE OPERATOR
The enclosure is 10 mm thick so as to insure a full protection against UV and B rays.
AUTOMATIC SHUTT OFF OF THE UV LAMP
The UV lamp switches itself off automaticaly if the door is opened by accident while the lamp is still active.
*PCR is a patented process owned by Hoffmann-La Roche
|
|
AirClean Systems AC600 Series Ductless Workstations
Our most economical workstation for operator and environment protection. Safely remove toxic vapors, gases, fumes and particulate.
Ideal for:
General chemistry involving small volumes of common chemicals
Tissue staining and processing; e.g. histopathology, cytology
Gluing operations
Solvent cleaning of electronic parts
Soldering applications
School demonstration workstations
Forensic applications - containment of fingerprint powders and chemicals such as ninhydrin and cyanoacrylate
Animal necropsy
Standard Features:
AirSafe™ automatic safety controller
Integral base with deep spill lip
No ducting required
Minimal installation - plugs directly into a standard 110V or 220V electrical outlet Extremely quiet operation < 49dB
All thermoplastic construction with application specific sash, base and enclosure material
Available in “low-profile” or tall version 32” or 48” widths with nominal 24” depth
UL, CSA and CE listed
|
|
The fume cabinet, fume hood and extraction chamber all in one.
Ideal where complete freedom is required to work on several processes at once and where ease of visibilty is essential. Where fumes spread rapidly, for example in draughty working conditions, the Cleancab™ can enclose the source, enabling fumes to be captured before they contaminate the workplace.
Cleancab™ fume hoods: -
Have a shatterproof clear polycarbonate hood
Utilise a chemically resistant base
Include an integral airflow valve
Are heat resistant
Are ESD safe
Are easily cleaned
|
|
| ... products without technical information |
| |
|
The LISA wall-mounted distribution boxes suit applications where low space is available.
|
|
|
The PSSR Universal Patch and Splice Sliding Rack Mount Panel is an excellent choice for applications requiring an extremely compact and easy-to-use design. It is used to patch, or to patch and splice fibers and to provide cross-connection capability. It accommodates up to 24 connections and can use a wide variety of connector types. The panel can be installed in either a 19” or a 23” rack and occupies only 1.75” 1U of rack space. Splice trays and internal fiber management are housed in a sliding drawer that latches securely in both the open and closed positions. Jumpers can exit either to the left or right at the front of the panel.
|
|
FIBRE MANAGEMENT IN CABINET, PATCH PANELS & DRAWER
Optical Fibre Splice Tray Lid
Managed with Radius Control and Dark Fibre Storage
Plain with Basic Storage Facility
Optical Fibre Splice Tray Hinge and Holder
Array Tray and Isolator Clips
Fibre Clips and Coupler Clips
Optical Fibre and Ribbon Fibre Splice Protector
900 Micron Buffered 15-Way Fibre Clip
Optical Fibre Flat Manifold
Strain Relief Boot - 900 Micron Fibre
Quick Panel Mount Strain Relief Gland and Slot In Version
900 Micron Boot and Short Buffered Fibre Boot
Optical Fibre Coiling Clip
Chain Plate
Optical Fibre Support Base, Network Saddle and Expandable Bracket
Dust Caps with Flexible Ties or Metal Chains
Optical Fibre Connector Cutout Adaptor and Cover
Snap Latch
8-Way SC Adapter
|
|
KITS
Amphenol Fiber optic provides termination kits for maintenance on cable assemblies and terminating cable assemblies on single or multiway butt joint and expanded beam connector. These kits contains all necessary tools to terminate connector.
To use the kit with benefits, a minimum training is required.
OTHER FIBER OPTIC PRODUCTS
As part of our Total System Support policy, Amphenol expertise and support are at your service from R&D to prototyping and production of transmission links as well as special devices and cabling or repairs.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
