|
|
| ... products without technical information |
| |
The DP/DP coupler interlinks two PROFIBUS DP networks and permits data transmission between the masters and the two DP networks. The maximum size of the transmitted data is 244 bytes of input data and 244 bytes of output data. The DP/DP coupler is configured in the S7 software or by means of a GSD file.
Features:
° Up to 244 bytes of input data and 244 bytes of output data can be exchanged between two PROFIBUS networks
° Dual-redundant power supply
° Electrical isolation between the PROFIBUS networks
° PROFIBUS addresses can be set by DIL switch or software |
|
The CAN-Bus Tester 2 constitutes a universal measuring instrument for the commissioning, analysis, monitoring, troubleshooting and service/maintenance of CAN-Bus plants.
Typical problems which occur during the operation of CAN-Bus plants, such as node failures, faults in the communication or complete standstill of the plant, often have their origins in the physical bus characteristics. The CAN-Bus Tester 2 provides an overview of the signal conditions on the bus, which helps you locate and rectify frequently occurring error causes without unnecessary delay.
You can already ensure a correct bus cabling and verify its transmission properties when setting up the plant. You can also perform comparing measurements directly on the running plant over its lifetime and thus prevent downtimes. |
|
| ... products without technical information |
| |
A Machine¡G
NCG series is the latest generation of Moving style high accuracy high speed Coordinate Measuring Machine from LEADER¡Aat the same time highly stable and easy to use.
Design Characteristic
- Granite fixed worktable, all three axes are made of high performance granite, good temperature characteristic, have the same coefficient of thermal expansion.
- Granite worktable with high guide in X axis, eliminate the pitch and yaw ,also provides superior motion stability.
- Z axis air-balance with self-protection ,improve motion capability.
- Advanced synchronous belt drive system with non-slip and high stiffness, ensures high stabilit, lower noise.
NC351515 Performance Specifications
Measuring Strokes :3500 x 1500 x 1500(mm)
Resolution :0.2 (um)
Accuracy according GB/T16857.2-1997 equal ISO 10 360¡G
Volumetric length measuring error E =11+11L/1000umƒÍ
Volumetric Probing Error R = 12+12L/1000umƒÍ
Environment Specifications
Room required specifications
-Average room temperature: 18 - 22 ¢XC
-maximum thermal gradients:1 ¢XC/hour¡A2 ¢XC/day¡A1 ¢XC/meter¡A
-Air supply system
- (Min. air pressure) : 0.7 MPa
- (Min. air consumption) : 0.3 m3/min
Electrical requirements
- (Voltage) : 220 Vac „b 10%
- (Frequency) : 50 Hz
- (Current) : 10 A
Allowed Maximum Floor Vibration
- (Frequency Range): 0 Ĕ 19 Hz 19Ĕ75 Hz > 75 Hz
- (Maximum Amplitude): 0.0011 mm 0.0011Ĕ0.002 mm 0.002 mm |
|
| Continuous development has made scanning technology an indispensable technical production factor. Bridge-type measuring machines from Carl Zeiss, with VAST® and Navigator® technology for example, not only ensure a high level of process stability, they also fit seamlessly into the rough production environment as a result of their sturdiness and compactness. You can read more about the classic PRISMO®, as well as smaller measuring machines such as ACCURA® and CONTURA® G2 here. |
|
A. Machine
- Miracle787 MACHINE
- RENISHAW UCC Lite Control System
- Calibrate Ball with Support Base
- User and System Manuals
B. Computer System
- Minimum configuration: Pentium ¥³3.0 GHz/512MB RAM/80GB Hard Disk/32MB Graphic Card /17¡ÈColor LCD Monitor/ Window¡¯s OS
- HP Color DeskJet printer
C. Software System
-Amereican Rantional DMIS software(for Windows XP)
DMiracle 787 Performance Specifications
Measuring Strokes :700(mm) x800(mm) x 700(mm)
Overall Dimension : 1600(mm) x 1950(mm) x3000 (mm)
Max part weight : 1000 kg
Resolution : 0.2 (um)
Accuracy according GB/T16857.2-1997 equal ISO 10 360£º
(Volumetric length measuring error) E =2.9 +4L/1000um
(Volumetric Probing Error) R = 3.0um
D. RENISHAW Probe System |
|
Features:
Particularly suitable for large components and high-accuracy work.
» Pneumatic counterweight for Z axis.
» Smooth and low-vibration motion in axes thanks to granite guides.
» Parallel drive of the two longitudinal axes, therefore no contouring error.
» Robust design with high load capacity.
» Brushless drive systems.
» Low air consumption.
» Wear-free data acquisition thanks to optoelectrical measuring scales.
» Resolution: 0.15µm |
|
• High-accuracy natural stone guides permanently ensure excellent measuring accuracy,
• Precision air-cushion bearings,tried and proven thousands of times, assure high measuring accuracy, reduce energy input, and guarantee smooth, low-vibration movement,
• Non-contact scale rules ensure low-wear, high-precision data acquisition on all axes,Resolution: 0,15 µm
• Can be equipped with active vibration damping systems,
• Pneumatic counterweight for Z axis,
• Digital motors. |
|
| A large-capacity bridge-design multisensor metrology system, SmartScope® Flash™ 500 uses video measurement and a complement of sensors, including a new through-the-lens (TTL) laser, for complete part dimensioning. Its generous 500x450x200 mm XYZ measurement volume accommodates large parts with sub-micron precision. |
|
| An automatic, benchtop, multisensor dimensional measurement system with fully telecentric TeleStar® 10:1 zoom lens, providing consistent feature sizes anywhere within the field of view, at any magnification. Uses video, touch probe, laser, and/or micro-probes to completely characterize a part in a single setup. |
|
Inspect3D supplies high-capacity gantry machines with air-cushion bearings for highest demands. An open gantry design is the ideal system, permitting easy access to the components to be measured.
Particularly suitable for large components and high-accuracy work.
» Pneumatic counterweight for Z axis.
» Smooth and low-vibration motion in axes thanks to granite guides.
» Parallel drive of the two longitudinal axes, therefore no contouring error
» Robust design with high load capacity.
» Brushless drive systems.
» Low air consumption.
» Wear-free data acquisition thanks to optoelectrical measuring scales.
» Resolution: 0.15µm |
|
The LAMBDA carries out the quadrature of the circle which consists in associating great capacities of measurement, a high rate of travel and an excellent measuring accuracy.
One or more gantries ensure measurements on sizes of machine being able to reach more than 20 meters.
|
|
The range of particularly wide machines TOTAL STATUS offers more than 60 models different in term from size (500 to 2000 mm), from equipment and environmental conditions.
Certain models require a air-conditioned environment, others can evolve/move in a medium of workshop having variations in temperature of 15° and more.
Capable of point-to-point measurements, with continuous scanning by contact or optics, machines TOTAL STATUS are equipped with powerful software PCMDIS common to all the range of the machines Hexagon Metrology.
|
|
| Machine of measurement whose guidance is elevated there compared to the scheme of work what allows a use as an aggressive industrial milior, or the traditional machines gantry are inoperative |
|
Measurable work pieces
- all types of gears with the standard Software package
with optional Software package:
- measurements of prismatic parts and Free Form Surfaces with Wenzel CM-Software
- Worms and Worm gears
- Bevel gears
- Tools like hobs, shavers and shapers
- Other rotational symmetric parts
- Special profiles
- Scanning of unknown contours
Technology:
- Bridge type GMM with rotary table integrated in the machine base
- Machine base of massive dark granite
- Active damping system
- Thermal stability through the use of identical material for base and axes
- Air bearings on the linear axes
- Wenzelgeco CNC-Controller designed to meet the spezial requirements of high precision measuremts
- Scanning 3D probe, optional probechanger
Technical data:
- Work piece diameter w/o probe changer min./max. 5 - 1000 mm
- Internal work piece diameter > 12 mm
- Module min./max. (0,2) 0,5-25 mm
- Helix angle < 90 °
- Measurable face width max. 600 mm
- Number of axes 4
- Measuring precision according to VDI/VDE 2612/2613 Gruppe I
- Axes travel X-Axis 1000 mm, Y-Axis 1200 mm, Z-Axis 800 mm
- Type of Rotary Table L400 (L300)
() optional |
|
Measurable work pieces
- all types of gears with the standard Software package
with optional Software package:
- measurements of prismatic parts and Free Form Surfaces with Wenzel CM-Software
- Worms and Worm gears
- Bevel gears
- Tools like hobs, shavers and shapers
- Other rotational symmetric parts
- Special profiles
- Scanning of unknown contours
Technology:
- Bridge type GMM with rotary table integrated in the machine base
- Machine base of massive dark granite
- Active damping system
- Thermal stability through the use of identical material for base and axes
- Air bearings on the linear axes
- Wenzelgeco CNC-Controller designed to meet the spezial requirements of high precision measuremts
- Scanning 3D probe, optional probechanger
Technical data:
- Work piece diameter w/o probe changer min./max. 5 - 500 mm
- Internal work piece diameter >12 mm
- Module min./max (0,2) 0,5-20 mm
- Helix angle <90 °
- Measurable face width max. 300 mm
- Number of axes 4
- Measuring precision according to VDI/VDE 2612/2613 Gruppe I
- Axes travel X-Axis 500 mm, Y-Axis 600 mm, Z-Axis 400 mm
- Type of Rotary Table L300
() optional |
|
| ... products without technical information |
| |
Rigid toothed belt axes in 2 sizes. Select and attach drives freely or even with integrated drive and control for easiest initial start-up and wiring. Control directly from SPS(I/O) or over fieldbus.
|
|
The basis of the system program consists of portal-, vertical- and telescopic axis of the line AXS. These modules from the system program can be combined any way or with the line AXC to create optimally construed multi linear axis systems.
• Custom- made solutions by using components which are individually harmonised with the application: Linear axis with rack and pinion drive are especially suitable for applications with great stroke length - up to 12 m self- supporting, as butt joint version theoretic unlimited stroke length.
• Z- axis for taking vertical loads up to 1000 kg.
Optimally construed multi linear axis systems harmonised with the focal points of the customers requirements: Portal axis, Z- axis and telescopic axis from the system program can be combined any way.
|
|
High rigidity and flexible fitting by highst precision in manufacturing. Flexibly expanding intermediate positions increase the possibility of applications.
|
|
Two Axes of Motion in One Housing!
Rigid Design Holds Guide Shafts at Both Ends
Deflection Under Heavy Loads is Greatly Reduced
Air Cushions Standard on 1" & 1.5" Bore Sizes
Precision Mounting Surfaces with Tooling Holes for Grippers and Tooling. Custom Faceplates are Available
Heavy Wall Cylinders Built Into Housing
Case Hardened Shafting
Composite Bushings or High Precision Linear Ball Bearings Provide Accurate and Repeatable Motion
Floating Couplers
Pre-Mounted Cable Carriers
Adjustable Shock Absorbers
Optional Threaded Stop Collars for Fine Stroke Adjustment
Dovetail Sensors with Optional "Quick Disconnect" |
|
an electric linear module for Gantries with linear Axes
example: Gantries and systems multi axes |
|
|
|
see the results for the following category
