|
|
Hydraulic clamps and clamping cylinders
single or double acting
max. clamping forces from 2.2 to 50 kN
max. operating pressure from 100 to 500 bar
max. clamping strokes from 3 to 16 mm
|
|
|
|
|
|
Horizontal Zeropoint Quickclamping cylinder with piston-catching
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Size: K20, K40
Explanation:
With our new Zeropoint Quickclamping cylinder with piston-catching, we make the palletizing asier and quicker.
• No search of drilling
• No damage of zero point drilling and nipples
• No risk of injury
Releasing and taking out of the pallet, take place still faster and simpler, because of the linking with the crane which is not more necessary during the release phase
Thanks to the speed of pelletizing, you reduce considerably your pelletizing period and consequently your costs.
Advantages:
• With and without blow out
• Completely in stainless steel
• Applicable in all positions without fit-up aids
• When the mechanism is out of service, the piston-catching stay out, it can be locked, thus the discs spring are not forced.
Can be integrated in:
• Clamping towers
• Clamping angles
• Automatized handling devices
• General mechanical
Note:
As standard, there is a manual or hydraulic advance motion of the piston-catching.
On request:
- Installation diagrams on request
|
|
|
|
|
|
Bluid-in Zeropoint Quickclamping cylinder K5, round
Screw-in version
Hydraulic release (or pneumatic)
Cover and piston hardened
Repeat accuracy < 0,005 mm
Assembling diameter Ø 39 mm
Pull in force 5 kN (hydraulic)
Pull in force 1,5 kN (pneumatic)
Holding force 13 kN
Use:
With a small footprint for installation in base plates, machine tables, clamping profiles, columns and towers, swivel bridges, machine pallets and clamping pallets. Also suitable for use as „cylinder locks“ with high repeatability.
Note:
Installation Zeropoint Quickclamping cylinder with a low installation height of 19.8 mm and an installation diameter of 45 mm (M45 x 1). Hydraulic pressure is only needed for unclamping (min. 40 bar / max. 50 bar). The installation Zeropoint Quickclamping cylinder is mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage. The contact surface is the upper surface of the housing.
On request:
- Installation diagrams on request
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
|
|
Bluid-up Zeropoint Quickclamping cylinder K5, round
Hydraulic release (or pneumatic)
Cover and piston hardened
Repeat accuracy < 0,005 mm
Global diameter Ø 62 mm
Pull in force 5 kN (hydraulic)
Pull in force 1,5 kN (pneumatic)
Holding force 13 kN
Use:
For mounting on machine tables, clamping profiles, columns and towers, measuring machines, assembly stations.
Note:
Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The Zeropoint Quickclamping cylinders are mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage. The contact surface is the upper surface of the housing.
On request:
- Individual housing can be supplied on request
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
|
|
Twist Clamp Cylinders
Combines linear and 90-degree rotary motion with an internal pin/cam mechanism.
Rotary action moves a clamping arm away from the workpiece, allowing for easy loading and unloading of parts.
|
|
|
|
|
|
Bluid-in Zeropoint Quickclamping cylinder K10, K20, K40, round
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Assembling diameter: K10: Ø50mm, K20: Ø78mm K40: Ø102mm
Max. pull in force 40 kN (hydraulic)
Max. pull in force 30 kN (pneumatic)
Max. holding force 105 kN
Use:
With a small foot-print for installation in base plates, machine tables, clamping profiles, columns and towers, swivel bridges, machine pallets and clamping pallets.
Note:
The installation Zeropoint Quickclamping cylinders have high holding and pull-in forces with very small installation dimensions. Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The Zeropoint Quickclamping cylinders are mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage.
On request:
- Installation diagrams on request
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
- Also available as an individual flange version
|
|
Bluid-up Zeropoint Quickclamping cylinder K10, K20, K40, round
Hydraulic release (or pneumatic)
Cover and piston hardened
Repeat accuracy < 0,005 mm
Global diameter: K10: Ø78mm, K20: Ø112mm K40: Ø148mm
Max. pull in force 40 kN (hydraulic)
Max. pull in force30 kN (pneumatic)
Max. holding force 105 kN
Use:
For mounting on machine tables, clamping profiles, columns and towers, measuring machines, assembly stations in connection with clamping flange no. 6370ZB.
Note:
Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The modules are mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage. The hydraulic version has 1 connection for clamping / unclamping (G1/4 or G1/8).
On request:
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
- Can also be supplied with centering pins for quicker and more precise installation
|
|
|
|
|
|
Bluid-in Zeropoint Quickclamping cylinder K10, K20, K40, square
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Assembling diameter: K10: Ø50mm, K20: Ø78mm K40: Ø102mm
Max. pull in force 40 kN (hydraulic)
Max. pull in force 30 kN (pneumatic)
Max. holding force 105 kN
Use:
Can be used as a single clamping point or combined with round installation Zeropoint Quickclamping cylinders in base plates, machine tables, clamping profiles, columns and towers, swivel bridges, machine pallets and clamping pallets. A square Zeropoint Quickclamping cylinder prevents the pallet from twisting. The indexing function enables positioning every 90°. Specially suitable for use in turning.
Note:
The installation Zeropoint Quickclamping cylinders have high holding and pull-in forces with very small installation dimensions. Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The Zeropoint Quickclamping cylinders are mechanically locked in the clamped position. The advantages of this are that there are no cumbersome lines and no danger of leakage. Square pallet for screwing onto the pallet see item no. 6370ZA.
On request:
- Installation diagrams on request
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
|
|
|
|
|
|
Bluid-up Zeropoint Quickclamping cylinder K10, K20, K40, square
Hydraulic release (or pneumatic)
Cover and piston hardened
Repeat accuracy < 0,005 mm
Size: 85x85mm, 120x120mm, 150x150 mm
Pull in force 40 kN (hydraulic)
Pull in force 30 kN (pneumatic)
Holding force 105 kN
Use:
Can be used as a single clamping point or combined with round surface-mounted Zeropoint Quickclamping cylinders in machine tables, clamping profiles, columns and towers, measuring machines, assembly stations in connection with clamping flanges no. 6370ZB). Clamping flange size 20 for K10, size 40 for K20, for K40 integrated onto the housing.
Note:
Hydraulic pressure is only needed for unclamping (min. 50 bar / max. 60 bar). The Zeropoint Quickclamping cylinders are mechanically locked in the clamped position. The ad-vantages of this are that there are no cumbersome lines and no danger of leakage. The hydraulic version has 1 connection for clamping / unclamping (G1/4 or G1/8). Square pallet for screwing onto the pallet see item no. 6370ZS.
On request:
- Automation solutions such as media ducts, sensor of locking monitoring, blowing off and isolated applications
- Can also be supplied with centering pins for quicker and more precise installation
|
|
Zeropoint Quickclamping compact cylinder
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Size: K10, K20
Use:
For retrofitting to modular profiles, columns, tombstones and cubes. Can be used with thin wall sections..
Note:
There are 5 standard connection options. 4 connections are installed laterally on the outside surface at a 90° angle. Connection is also possible in the base of the Zeropoint Quickclamping compact cylinder.
On request:
- Installation diagrams on request
- Automation solutions such as blowing out, blowing off, isolated applications, sealing air and media ducts
- Individual solutions, such as nipple and installation compatible or installation compatible for existing systems
|
|
Zeropoint Quickclamping cylinders with pusher and central locking against pollution for automatised solutions
Hydraulic release
Cover and piston hardened
Repeat accuracy < 0,005 mm
Assembling diameter Ø 78 mm
Pull in force 20 kN
Holding force 55 kN
Use:
For installation in base plates, machine tables, clamping profiles, columns and towers, machine pallets and clamping pallets.
Note:
Through the central locking the pollution particles can not go into the nipple bore. The central locking element advances with an individually defined spring force
Blowing out and sputter functions
On request:
- Installation diagrams on request
- Hydraulic move-out of central locking
|
|
|
|
|
|
Zeropoint Quickclamping cylinder with release and contact controls for automatised solutions
3 possibilities of monitoring:
- Pneumatic monitoring:
Function of blowing out by compressed air for the cleanliness of support surfaces. After the installation of the pallet of workpieces, it occurs in the pressure line a dynamic pressure, of which this one could be detected by the mean of a pressure sensor.
- Electric monitoring:
Direct position monitoring of the clamping piston in the Zeropoint Quickclamping cylinder by the mean of an inductive sensor. Electric signal when the Zeropoint Quickclamping cylinder is clamped. Small height necessary for the assembling like for the Zeropoint Quickclamping cylinders K5 (19,8 mm) and K40 (42 mm).
- Hydraulic monitoring:
Monitoring of the clamping piston by a hydraulic closure valve. Dynamic pressure when the Zeropoint Quickclamping cylinder is opened, which can be detected by mean of a pressure sensor. Free hydr. flow when the Zeropoint Quickclamping cylinder is closed. Despite a hydraulic sensor, only small height for assembling is necessary.
|
|
Size: K20 ITH6
Zeropoint Quickclamping cylinders with turbine for automatised solutions with:
• Turbine function for complete cleaning of support surfaces without „shady side“
• Central locking against pollution particles
• Hydraulic or pneumatic locking sensors
• Control of contact by air blocked
• Hydraulic pre-expulsion for palletizing solutions with also possibility to swing completely free during the catchment
• No damage of media-coupling
|
|
Zeropoint Quickclamping extrusion cylinder for applications by:
• Round tables and 5 axes milling machines, turning machines
• Better level holding
• Large support surface
• Free passage for flange piece, tubes, forks ...
|
|
REMARK
1 : The mounting surface finish should be no rougher than Rz 6.3 (ISO 4287:1997).
2 : Be sure to use O-ring included at all times.
3 : Tightening torque for mounting should be as per the above table.
4 : The hardness at the top portion of round top type plunger is HRC54.
|
|
* Maximum operating pressure 500 bar
* Short delivery times - Large stock range
* Piston diameters from Ø25 mm to Ø40 mm
* Rotates to left or right with 45, 60 or 90° angle of rotation
* Integrated in a tool without lining
|
|
|
|
|
|
030 - SELECT Hydraulic Swing/Pull Clamp
SELECT hydraulic threaded body swing clamps are high quality and cost effective alternatives to competetive brands.
- Range of sizes
- available in sigle or double acting versions
- field adjustable swing direction
- MRO interchange
035-1 - SELECT Pneumatic Swing/Pull Clamps
SELECT line of pneumatic swing/pull clamps are designed for applications not requiring hydraulic power. The fast acting clamps can generate up to 50 pounds of clamping force from shop air.
- Swing motion available in 0, 45, 60, and 90 degrees
- Four styles of arms
- Double-locked arm design is bolted to piston shaft and around shaft diameter for extra rigidity
- Double-acting design
727D - Hydraulic Swivel Clamping Cylinder
Hydraulic swivel clamping cylinders are particularly designed for applications which require high clamping forces and easy loading of workpieces in confined spaces.
- swivel left
- max. clamping force 475, 850, 1250 daN
- max. operation pressure 250 bar (3625 psi)
|
|
SPEEDY classic - mechanically / hydraulically
- Our most complete and versatile system available in 4 sizes with draw in forces from 5.3 to 30 kN
- Draw in- positioning - clamping - releasing- retraction, all these functions are integrated in a single element best suited for full automatic solutions
- decades have proven the wide range of applicability of this zero point mounting system
SPEEDY metec - mechanically
- easy-to-handle
- Reduce setting up times and be flexible with the SPEEDY metec
- High clamping forces
- robust system
- in 3 sizes available with clamping forces of 12 kN / 20 kN / 50 kN
- No additional media required (compressed air, hydraulic fluids)
- Economical
SPEEDY airtec - mechanically/pneumatically
- well suited for most areas of application
- only one mounting nipple size, suitable for all sizes
- available in different variations (central locking, Index bores for the locking pistons and mounts with integrated blow off)
|
|
Linear Pneumatic clamping cylinder, cylinder or combi-tensioning swivel clamp cylinder
linear or swivel the clamping unit with compressed air
Self-locking clamping 9000N
32mm clamping away (10mm in swing clamp)
Overload protection
Swivel angle max. 120 ° adjustable
Various mounting options
|
|
Zeropoint Quickchanging cylinder for turning machine with passage for spindle nose ...
• Quick changing of chuck, tongs and special equipment
• High-precision of radial positioning or arresting
• Media ducts against chuck lubrication, hydraulic clamping and exact points for cooling and cleaning.
• Blowing off and sputter
• Great holding force and form fit
• Release control
• Safety system in case of interference, thus low risk of damage of the machine
|
|
| ... products without technical information |
| |
MW Cylinders Parker's MW range of cylinders is designed for medium and heavy duty industrial and mobile applications.
Two versions are available: the MWA Series for use at working pressures up to 250 bar, and the MWB Series for 160 bar applications.
The MW range of cylinders is of welded construction at the cap end, with a threaded rod bearing at the head housing the gland seals.
Standard pressure: up to 160 bar (MWB) and 250 bar (MWA)
Bore sizes: 32mm to 200mm (MWB) and 50mm to 200mm (MWA)
Piston rod diameters: 14mm to 125mm (MWB) and 32mm to 200mm (MWA)
5 standard mounting styles
Stroke lengths up to 4000mm
Standard temperature range: -30°C to 80°C
Options include air bleeds, position switches and custom paint finishes
Special designs to customer specification nbsp;
|
|
HYDRAULIC CYLINDERS
The offer includes standard catalogue hydraulic cylinders as well as non-standard cylinders designed and produced based on the arrangements with the customer or according to the documentation provided.
Primary offer:
Two-way operation hydraulic cylinders with a two-sided piston rod.
Two-way operation hydraulic cylinders with a one-sided piston rod.
Plunger hydraulic cylinders.
Cylinder eyes.
Applications:
Shipbuilding, metallurgy, transport, machines, process lines, hydraulic presses.
Characteristics:
reliable and long operation in hard conditions,
various types of fixing:
- on eyes with a self-aligning bearing and a bush,
- flanged,
- on arms,
- on pins.
piston diameter from 25 to 160 mm, of nominal operating pressure of up to 16 MPa and stroke of 3,000 mm,
maximum pressure: 25 Mpa,
required filtration precision 0.025 mm,
maximum piston speed 0.5 m/s.
|
|
We deliver a wide range of cylinder types, such as: Double acting cylinders
Single acting cylinders
Plunger cylinders
Double acting telescopic cylinders
Stainless steel cylinders, oli- and water hydraulic
Centre hole cylinders
ISO norm cylinders
Hydraulic cylinders with integreted transducer, inductive proximity switches etc.
Hydraulic cylinders with any integrated valves (build in valves)
Hydraulic special cylinders
DNV type approved hydraulic cylinders
GL type approved hydraulic cylinders
Special piston rod and tube materials
Special mountings
Hydraulic cylinders with special certificate
Special surface treatments
|
|
3000 PSI WHD SERIES CYLINDER
FEATURES:
Configurable custom rod design
1-2 week lead-time
manufactured with Parker “Zero Leak” sealing technology
BENEFITS:
Additional outside diameter lip that prevents contaminates from entering the system by bypassing the OD of the wiper body.
Superior BTU rod seal increases the conformity of the seal to the rod. The second lip on the seal improves stability, limiting the rocking motion of the seal to reduce seepage
Buffer ring acts as a primary seal and pressure spike suppressor. The combination of rod seal and buffer ring results in an exceptionally dry rod for longer life.
Piston includes 2 wear rings and bronze filled PTFE seal designed for extension free, leak proof service
1045/1050 chrome plated, induction hardened, 100K rod is more resistant to damage to rod and seal
1026 DOM cylinder tube bores are skived and roller burnished to provide precision finishes for extended seal life
|
|
Pressure capacity: from 500N (50Kg) up to 120KN
(12,000Kg)
Position repeatability: +-0.005mm
Sensor function: Set position stop, Set load stop, Set
distance stop,
Const. Load / Set Timed Stop
Const. Load / Set Stop Position
External input/output: 17 input, 16 output
|
|
|
Ready to mount 2- or 3- axis systems are also available for electrical cylinders with 24 VDC pulse or 230 VAC servo motor. Thereby the x-axis is a slider type with iron base.
|
|
|
|
see the results for the following category : 
