|
|
Features:
-Superior Low Energy Control for Micro Welding
-Ultra Fast Closed Loop Control
-Single Phase Power Supply
-Three Feedback Modes for DC Welders
-Graphical Display and Intuitive DC Welder Monitoring
The UB25 linear DC welder provides unsurpassed levels of control for micro-miniature resistance welding. This DC welder power supply should be used for smaller applications where closed-loop feedback control and fast response times are required. Safety critical applications such as those found in the medical and automotive markets will benefit from UB25’s precision low energy control.
|
|
Features:
-Superior Low Energy Control for Micro Welding
-Ultra Fast Closed Loop Control
-Single Phase Power Supply
-Three Feedback Modes for DC Welders
-Graphical Display and Intuitive DC Welder Monitoring
The UB25 linear DC welder provides unsurpassed levels of control for micro-miniature resistance welding. This DC welder power supply should be used for smaller applications where closed-loop feedback control and fast response times are required. Safety critical applications such as those found in the medical and automotive markets will benefit from UB25’s precision low energy control.
|
|
No matter what the application, Draeger's System Centers will design a monitoring system for your specific needs.
Whether it is a single wall mount unit for only one or a few points, a 19" rack mounted modular controller, or a full blown SCADA system with cabinetts to house the electronics and wiring, our experienced engineers will help to design the system that fits. Even PC monitoring consoles with event log displays and zoom-in plant layouts are available from Draeger Safety.
|
|
Acting as the nerve center of a modular gas detection network, the Vulcain 301C provides continuous monitoring of up to 96 inputs/outputs, on 3 distinct channels, at distances of up to 2000 feet.
Once installed, this highly customizable and powerful tool provides around the clock protection identifying hazards and triggering appropriate reactive measures such as ventilation activation.
|
|
|
The DC controller is designed to operate with DC commutator series wound or compound wound motors for pump drives. It is microprocessor controlled and designed to be cost effective and to occupy as small an outline as possible for a given output power.
|
|
The Iskra AC controller is a three phase controller for AC induction motor, which is mainly suitable for traction applications. It is designed around a high performance DSP processor, which performs real time flux vector control of an AC induction motor. The result is outstanding motor dynamics and efficiency. In the same unit can be additionally included the DC controller for DC commutator motor for drive the hydraulic pump.
Flexible communications with built in CanOpen protocol and simple electrical connection make this system an ever more attractive choice for mobile hydraulic applications.
|
|
|
The CVC electronic controller has been designed as control system for hydrostatic tracks vehicles with separate - left and right - hydraulic circuit. The CVC controls in closed loop the displacement of the two pumps, or the speed of the two wheels, to make sure that it corresponds to the given command in whatever use conditions.
|
|
|
The Waukesha Engine System Manager (ESM) is a total engine management system designed to optimize engine performance and maximize uptime. The ESM integrates spark timing control, speed governing, detonation detection, start-stop control, diagnostic tools, fault logging and engine safeties.
|
|
BODAS controllers for quickly and affordably creating a mobile-hydraulic complete solution without time-consuming and expensive hardware development.
The RC controllers are the heart of the BODAS system with multifunctional inputs and outputs for the control of the electrohydraulics components in the machine. BODAS RC controllers are optimally meeting the requirements of mobile working machines with a diversified application spectrum.
In complex applications, multiple controllers can be connected via the CAN bus to form a network. The number of the inputs and outputs can be extended quickly and economically with the CAN I/O-extension module RCE. Safety features integrated in the standard version enable simple and reliable machine diagnostics.
Matched to the RC controllers, the BODAS software modules offer preconfigured application solutions for drive and working hydraulics. A comprehensive tool chain for parameterization, for diagnostics and for flashing the BODAS controllers is available with the BODAS-service.
For custom solutions, you can use the BODAS RC controllers as a freely programmable platform.
Features:
- Safety features:
-Detection of cable break
-Detection of short circuit
-Monitoring the outputs
-Bosch watchdog module
-Central switch for all power outputs
- Output stages with pulse-width-modulated current regulation (PWM)
- Robust case
- High EMC > 100 V/m
- Download the software from a PC to the flash memory
- CAN bus or RS232 interfaces
- Interfaces matched to Rexroth electrohydraulics
|
|
Microvision Plus (3 axis interpolated controller)
All the power of a numeric controller with ISO programming in a cheap structure based on a RISC 16 bit processor. Monochromatic 5” display can be touch screen which improves navigation making it more user friendly. Drivers can be connected to the controller either through analog +/-10 V. signals or digital PWM or Step / Direction. Besides a considerable number of I/O “on board” many other devices can be added or remoted using the 2 available CANopen serial ports.
|
|
From the monitoring-for-function of the sensors to self-monitoring Control Units, Mayser supplies the right Control Unit for every safety system. Acting as a link between the sensor and the machine control, it analyses the incoming signals and immediately triggers the required measures.
In cooperation with the Elge GmbH company, we can also supply Control Units for special safety systems and other applications.
|
|
Control unit unipos C110:
- linear path controller
- CNC + PLC
- controls max. 9 axes, servo motors or stepper motors
- DC motors on request
Control unit Unipos 120 / 220:
- Point to point controller
- Control unit to control stepper motors
- CNC
Control unit unipos 420-W:
- continuous path controller
- CNC + PLC
- Controls max. 8 axes, 4 axes simultaneous
Control unit unipos 820-W-/WH:
- CNC-Controls + PLC
- max. 64 axes with 8 NC-channels (SERCOS/Analog)
|
|
Users of conventional universal display units can have difficulty in making use of their device´s options menu. Special applications require many more functions that are often not available with conventional units.
KRAL BEM 300 to 500 electronic units enhances the KRAL Volumeter performance.
Your advantages:
- Two-channel, i.e. differential measurement.
- Temperature and pressure pulse compensation.
- Measurement conversion.
- 7 point linearization.
- Limit value for a relay output, i.e. regulation of a bypass valve.
- Threshold value for signal suppression.
- Clear and easily readable display.
- Accurate handling by the use of a clear menu structure.
- Multiple mounting options. (KRAL Volumeter, wall, pipe, control panel).
|
|
ICU INJECTOR CONTROL UNIT - EFS 8412
PRESENTATION
The 8412 module is designed for use with the ITB 234V test bench
enabling automatic analysis of diesel or gasoline jets via image
processing. It handles the injector driving by means of an Ipod power
module, as well as driving the camera, the fog extraction system
and the light sources (laser or strobe).
USE
The ICU system provides the TTL command signals for driving an injector and the equipment necessary for image acquisition. It must be accompanied by an additional power module adapted to the injector to be driven. For this, EFS offers the IPOD modules for solenoid and piezo-electric injectors.
Injector driving
The ICU system drives the injector with a temporal resolution of 0.1 µs. It can handle from 1 to 10 injections per revolution at frequencies of between 0.1 and 10 Hertz.
It can run in two modes :
- « Signal generator » mode
The driving is based on the injection parameters entered by the user from the supervision PC. The injector command can be inhibited while allowing other signals to be generated thus enabling the calibration of the vision system without injections.
- « One shot » mode
The ICU module receives external information (an impulse on a logical input) on the START input which synchronizes the execution of a single injection cycle (one motor revolution).
|
|
|
VM20 is a modular, multipurpose measuring and test system for grinding machines easily programmable by the user. Available as independent unit or for rack-mounting, equipped with local hardware or remote operator panel as well as with Windows Software panel, digital I/O logic interfaces, Profibus and RS232. The wide range of grinding wheels balancing devices, with or without embedded acoustic sensors, applicable on single or multiple grinding wheels or long grinding wheels, allow to automatically and rapidly reduce vibrations which generally cause errors and imperfections on worked surfaces. The wide range of AE transducers configuration available, with assembly both on rotating and stationary machine components, can be used to monitor the machine conditions, through FFT analysis, and to determine the grinding wheel position when it contacts the piece to be worked or the tool-dresser. During working, diameter and roundness gauges, as well as the pieces positioning gauges, allow to achieve a constant production quality together with a cycle time improvement, thanks to correct feeding speeds for roughing-out and finishing.
|
|
Combustion Control and Monitoring Systems
Combustion and emission control, why?
In 1997 with the Kyoto's Conference and its regulations, the Governments decided to pay more attention to the CO2 flue gases reduction.
The European target for CO2 reduction is 8% compared to the year 1990 values.
Ascon is one of the leaders of this new conscience of environmental effects, managing, energy and financial saving.
Four guide lines have been defined: energetic renewable resources , diffusion of implementations to improve the final energy use, electrical energy production, and urban road traffic reduction.
One of the most important steps is to improve the plants efficiency by means of the continuous control of the flue gases oxygen content.
This type of control enables:
combustion efficiency optimisation by means of the control of the air/fuel ratio (energy saving);
check of correct plant working under different operating conditions, simple identification of possible anomalies and then relevant corrections (safety);
reduction of Nitrogen oxide pollution (to reduce environment impact).
Remember, a correct combustion means: economy, safety, cleaning.
Clean Combustion = Energy and money saving
At present each moderate investment on this matter enables a considerable energy saving with the consequent money surplus which means a quick pay-back of the investment and more.
|
|
For Maximum Combustion Efficiency Through Complete Mixing Of Fuel Gas And Air.
Selas Combustion Controllers equipped with PosiMix® Mixing Valves are precision premix systems for blending fuel gas and air. They are suitable for most fuels, mixing them with room air and compressing the mixture to deliver a precise, preset gas/air ratio at uniform pressure to the burners.
FEATURES & BENEFITS
Completely self-contained
Capacities available from 500 to over 150,000 cfh of mixture
Output pressure to 6 psi
Precise gas/air ratio maintained over a wide turndown
Available with automatic ratio control
Low installation cost - single pipe delivery system for one or more control zones
For use with any clean commercial fuel gas containing less than 40% hydrogen
Rugged - provides years of trouble-free operation
Low maintenance
|
|
At ITT Water & Wastewater we produce practical and easy to use monitoring and control systems for many different pump and mixer applications. Our systems offer reduced operational costs, total overview, less report handling and better environmental control.
As well as supplying the hardware, such as pump controllers, sensors, electrical start equipment and cables, we also have software for running the system. The ITT Water & Wastewater AquaView SCADA system provides precise and effective monitoring and control.
Each control system comes with a host of well-thought-out functions. Good examples are comprehensive pump control functionality, advanced supervision of pump condition, accurate flow calculation and cleaning functionality. All functionalities are based on international experience in municipal wastewater.
|
|
Automation of pumps and valves helps to cut costs on a permanent basis and safeguards the reliable operation of your installations.
PumpDrive is the first variable speed control system that comes in a uniform housing design for three mounting methods and offers the user a comprehensive solution across a wide performance range. It allows quick, precise and continuously variable speed adjustment of a pump's drive. Thanks to absolutely reliable rotational speed optimization in line with demand, energy savings to the tune of 50% can be achieved.
LevelControl is an intelligent level control unit for single or double pump systems in applications that require reliable level control. LevelControl monitors and documents switching cycles. It ensures even distribution of pumping hours and optimum pump operation. This reduces downtime, maintenance and servicing.
PumpExpert combines three elementary functions. It is the first diagnostic system capable of issuing clear recommendations for action in the event of a disturbance or malfunction.
|
|
The CoMo Injection process monitoring system Type 2869A allows zero-defect injection molding production by analyzing the cavity pressure curve.
A bright 12.1" color touch screen monitor Type 5629A3 makes operation of the CoMo Injection system even quicker and easier, and accelerates communication with the system. The new IP Setup Program now being supplied with the system allows simple automatic detection and configuration of CoMo Injection units installed in production.
Version 2.0 of CoMo-MIS Type 2829A…, the database system for storing measured and calculated process data, is now also available in the four languages mentioned above.
All of the CoMo Injection and CoMo-MIS systems that have already been installed can be updated with the latest version. The IP Setup Program works with all CoMo Injection units equipped with Version 1.2.
|
|
The CoMo Logic is a y(t) control monitor with three real-time thresholds and elementary post-cycle curve analysis function. The following operating modes are available: 'GRAPHIC’ for displaying the y(t) signal characteristics, ‘TREND’ for displaying the last 118 peaks of the cycle and ‘PEAK’ with numerical display of the cycle peak.
By their web server functionality, CoMo Net and CoMo View are directly connected to the TCP/IP world. Many functions and information can be operated and viewed via familiar browser functions from any point worldwide, of course protected by security precautions and access authorization. A central storage of quality data from larger, complex production lines is significantly simplified and a cost advantageby use of an existing network structure . Also remote maintenance and diagnosis enable fast, qualified and cost-effective on-site help during servicing.
The dependent measurands, for example press force and displacement are recorded and their functional dependence is evaluated. The evaluation result can reject bad parts for reworking or classify production into different tolerance classes.
The CoMo View is equipped with an integrated 5,7" Touch Color-Display of 320x240 pixels. Possible connection of piezo, strain gauge and voltage output sensors as well as potentiometric displacement and angle sensors make this two channel control monitor versatile for most any application. Real-time capability is given via digital I/Os and a fast export of process data and measured curves add significantly to a safe process monitoring even at high cycle rates.
|
|
Features:
- Comprehensive visualisation software for displaying filling level in
silos and vessels
- Level display on a 5.7" touch panel, including trend
- Display in volume, percentage, height or weight
- Signal evaluation of 4-20mA analogue, digital input as well as the
- UWT Nivowave® Acoustic Wave sensor Modbus RTU
- Touch panel is available as a single component or integrated in a control cabinet
|
|
Bray Controls is proud to introduce the controller of state of the taps Brayline series 50, preceding the future methods of indication of position of the taps. The great experiment of Bray on the ground and a research and development intensives led to the development of general-purpose interruptory controllers of first order, intended for industrial automation. The controllers of series 50 send a signal of position of the actuator and tap to local and remote stations. The standard appliances 50-0400 have an aluminum castings case under pressure, waterproof (NEMA 4,4X). The cases of series 50-0700 are also out of aluminum castings under pressure, waterproof and explosion-proof (NEMA 4,4X, 7,9).
The apparatuses were designed in order to facilitate wiring and for a large variety of switches. The two series are characterized by internal parts of high-quality, the same robustness and same reliability.
|
|
The Universal Power Cell uses Hall Effect sensors that are not affected by odd waveshapes or frequencies. Also, no Voltage or Current Transformers are used.
The UPC is field scalable to match your pump motor. Complete information at loadcontrols.com.
The PMP-25V Pump Load Control takes the 0-10 volt load signal from the UPC, displays the Pump Load, and has the Set Points, Timers and Relay and Analog Outputs.
|
|
Freelance 800F - compact The solution ABB' S Freelance 800F control system combine easy engineering with open year, modern system architecture. Freelance 800F is proven in more than 14,000 applications - in all industries.
Compact The control system allows the integration off all common fieldbuses, leaving to use to select any they wish - whether FOUNDATION Fieldbus, PROFIBUS, gold BINDER.
The system was and will Be continously improved and enhanced to meet our user' S needs. Customers choosing Freelance 800F edge rest assured that ABB will long support them in the term.
The new AC 700F to control has just been released. In addition, new Information Management functions are available via PGIM 800F, our new Information Mananagment option.
|
|
Modern automation, control and remote control systems have become essential for optimized and secure control and monitoring of processes regarding energy distribution and industrial networks.
Depending on the specific field of application, different requirements have to be met by the devices regarding
- Various intputs and outputs
- Process signals
- Environmental conditions
- Communication and transmission technology
- as well as essential logical functions
|
|
The components presented here have been developed and optimised for increased requirements in close co-operation with our customers over a period of several years. ifm electronic now supplies a sophisticated control and automation system which conforms to the needs of the market. In addition to flexibility and performance attention was given to the following points:
> Operation at extremes of temperature, both high and low.
> The ability to withstand extreme shock and vibrational stresses.
> Use even with direct exposure to dirt, water and moisture.
> Insensitive to supply voltage fluctuations caused by the battery/generator systems.
> The electrical system must be insensitive to high levels of conducted and radiated interference.
> Application-related networking possible with the serial CAN bus suitable for mobile applications.
|
|
These solid state magnetic accelerators have been designed as speed input devices used for solid-state controls for electric vehicle traction motors. Applications include industrial fork lifts, utility vehicles, and airport ground support vehicles.
Input voltage : 18 to 80 volts DC
Output voltage (maximum) : 3.65 volts (nominal)
Output voltage (minimum) : 0.35 volts (nominal)
Start switch output voltage : Equal to user battery input voltage
Start switch output current : 3 amps continuous, 5 amps intermittent (10 seconds)
Note: This accelerator switch does not contain a 1A switch.
Features and Benefits:
- Start switch function is performed by a power MOSFET, in lieu of a mechanical device
- Typical actuator force is 5 lbs, and should not exceed 7 lbs
- Switch may be operated through a linkage mechanism or directly from the vehicle accelerator pedal
- Customer connection is made by means of a metric M10x1.5 male thread
- Underwriter's Laboratory Type EE construction, O-ring cover seal, blind mounting holes, and insulated wire hole grommet all combine to eliminate the need for periodic cleaning
- No mechanical adjustment required after installation
- Includes reverse battery protection and internal fusing for start switch over-current protection
- A hall effect sensor detects the input shaft displacement through the 0.75" shaft stroke
- Switch contains a push pull linear input shaft, with a typical 0.1" displacement for start switch closure
|
|
|
