|
|
|
|
|
|
Compared to the traditional handling devices such as hoists and pneumatic manipulators, the Intelligent Assist Devices by Scaglia Indeva provide relevant advantages:
Precise positioning of the load as they allow for accurate and rapid movements, while traditional handling devices overtravel, bounce and require lots of little corrective movements that reduce productivity.
Intuitive control: It features the “float mode” control or “hands on manipulation”, without actuating the control handle. It makes the most of the natural human ability to coordinate and control motion, thus allowing for a more intuitive control that means a more precise and quicker positioning of the load, especially when this has to be placed in a narrow target as gently as possible.
Improved ergonomics and no effort required. Thanks to the microprocessor based control, the system supplies energy to win inertia both during acceleration and braking.
Speed: IADs respond swiftly, yet smoothly to human touch; the operator notices no time lapse between the machine’s sensing and its response.
Automatic and immediate compensation to weight: it allows handling loads with different weights or loads that vary their weight during handling (emptying out containers) with no stop times at all for turning selector.
|
|
Handling large drum loads safely is no longer a problem: Our drum tongs, grippers, lifters and tilters allow both vertical and horizontal transport.
Even where space is restricted, the storage area can be flexibly loaded. Stable constructions and galvanized models ensure a long product life, which is guaranteed through our manufacturing competence.
|
|
|
The configuration choice gives you the possibility to adapt each solution to your specific mavimentation exigencies, depending also on the paricular working cycle.
|
|
Handling attachment with circular or properly shaped vacuum pad. Indicated for handling of metal or plastic barrels.
Vacuum generation by electric vane pump or pneumatic ejector (Venturi system).
Max capacity 35 kg.
Ergonomic handle.
Accessories: quick disconnection for suction pads, angular adaptor, flexible extended manouvre handle, etc.
|
|
Pneumatic linear manipulator with pneumatic gripping tool for parcels of ceramic tiles or for any part that can be gripped pushing on the sides.
Max capacity 200 kg.
Max work radius 7 m.
Max vertical stroke up to 2100 mm.
|
|
Transfercapacity: max. 250 Kg
Z-axis travel: low pos: 200 mm / high pos: 1860 mm
X-axis range: 1300 mm
Please note: Grippers for different EROWA tooling to be ordered seperatly.
Manipulator to be installed in front of a machining center where frequent changes of pallets are called for. Possible adaptions for all EROWA Tooling.
Gripper Order Numbers
ER-030192 Gripper ITS 148
ER-030194 Gripper ITS 148 swivelable
ER-030218 Gripper FrameSet
ER-033290 Gripper RCS swivelable
ER-042568 Gripper fork MTS 400
ER-044612 GripperFrameSet/RCS
ER-046144 Gripper RoboSet
ER-046160 Gripper RCS 1
ER-046161 Gripper RCS 2
ER-046162 Gripper RCS 5
ER-046163 Gripper fork UPC
ER-046164 Gripper fork UPC/RCS
ER-047400 Gripper RN PC 210
|
|
Pneumatic arm manipulators for handling, “weightless”, which allows the minimum effort for the operator, when using handling attachment for glasses, metal plates or panels.
Max capacity 600 kg
Max work radius 3.7 m
Max vertical storke 2.4 m
On customer request manual or pneumatic rotating or tilting devices can be supplied.
|
|
The ATISacer manipulators, endowed with a rope guided vertical movement unit, allows the handling of loads in any direction without ties, with extreme ease and precision.
They can be integrated with personalized gripping devices, planned and structured according to specific needs. They are equipped with movement units, necessary to the movement cycle, which can be manual or by means of pneumatic components.
The rope-guided ATISacer manipulators are available in the following configurations: column mounted installed to the floor, column mounted with self-firmed base-plate, overhead or sliding on overhead runway tracks.
The implant which regulates the functioning of the manipulator is powered only by the air in the network.
|
|
|
|
|
|
Brief description
The most advanced cable balancer is the Flexi-heffer. Useful for applications where loads can be lifted using a cable and/or can be handled flexibly or free-suspended. Ideal especially to the highly desirable added value generated by its user-friendliness and ergonomics. (For technical specifications: see table below)
Unique principle: ergonomic thanks to idle flexible arms
There is no other handling system with the same major advantage in day-to-day use as the BPL Flexi-heffer. What is unique are the idle flexible arms e.g there is no hoist drive inside or attached to the arms. The arms that carry the load are moved by the operator from ‘A’ to ‘B’. Movements, in particular horizontal, are extremely light because of the idle and flexible arms and the hoist drive which is mounted in the static column. Summarized the technology is sophisticated and yet surprisingly simple.
Speed and self-balancing: the second advantage
The idle arms allow easy manual movements in horizontal directions. Vertical movements are also very quickly. The Flexi-heffer is available for many years with the BPL control unit for self-balancing. This means that a series of different loads can be handled successively without the need for any weight adjustments. At the same time the vertical movements can be operated with the touch of a finger with acceleration and deceleration.
|
|
|
|
|
|
HANDLE YOUR PRODUCTS INTUITIVELY WITH ZE'SOLUTION SAPELEM
ECONOMICIAL
Electric energy.
Eliminate MSD.
INTUTIVE
Follow operators' nature gestures.
No bouton necessary to make movements.
No adjustment necessary to adapt mass changes.
REACTIVE
Reaction time < 0,1 s.
Acceleration up to 1 g.
Max Speed 2 m/s.
POWERFUL
From 0 until 300 kg.
Arm up to 4,7 m.
PRECISE
At Millimeter.
Arm in aluminium : Movements without resistance.
SECURE
Detector of hand presence.
Active security through embedded software.
Power-Cut Management.
ERGONOMIC
Ergo Conception : lightness, sensibility, visibility …
Design for left and right handers.
Effort to make movements < 20 grammes.
ALL PRODUCTS
Cans, boxes, bags, doors, windshields, bumpers, tanks, tubes, bottles, pallets, tyres, ham, spools, eggs, motor parts (water pump, etc.), metallic systems, windows, dashboards, sand core, equipments, moulds, parts of fuselage, yoghurt pots, exhaust system, car batteries, shower trays, sinks, sunroofs, motorbikes engines, bus windscreen, car doors, bonnets, steel cabinets, car seats, aeronautical parts …
ALL FIELDS
Food industry, aeronautics, car industry, textile, cardboard, glass, woodworking, plastic, chemistry, sheet metal, medical, warehouses, electronics, equipments, pharmacy ...
|
|
Dalmec offer a wide range of manipulators, fitted with custom-built tooling for the “weightless” handling of foundry products.
Simple to use, they allow the operator to move products quickly, accurately and safely within the operating area.
The type, design, dimensions and picking systems incorporated in these manipulators are tailored to suit the specific requirements of the user and the varying environmental conditions available.
|
|
|
|
|
|
HANDLE YOUR PRODUCTS INTUITIVELY WITH ZE'SOLUTION SAPELEM
ECONOMICIAL
Electric energy.
Eliminate MSD.
INTUTIVE
Follow operators' nature gestures.
No bouton necessary to make movements.
No adjustment necessary to adapt mass changes.
REACTIVE
Reaction time < 0,1 s.
Acceleration up to 1 g.
Max Speed 2 m/s.
POWERFUL
From 0 until 300 kg.
Arm up to 4,7 m.
PRECISE
At Millimeter.
Arm in aluminium : Movements without resistance.
SECURE
Detector of hand presence.
Active security through embedded software.
Power-Cut Management.
ERGONOMIC
Ergo Conception : lightness, sensibility, visibility …
Design for left and right handers.
Effort to make movements < 20 grammes.
ALL PRODUCTS
Cans, boxes, bags, doors, windshields, bumpers, tanks, tubes, bottles, pallets, tyres, ham, spools, eggs, motor parts (water pump, etc.), metallic systems, windows, dashboards, sand core, equipments, moulds, parts of fuselage, yoghurt pots, exhaust system, car batteries, shower trays, sinks, sunroofs, motorbikes engines, bus windscreen, car doors, bonnets, steel cabinets, car seats, aeronautical parts …
ALL FIELDS
Food industry, aeronautics, car industry, textile, cardboard, glass, woodworking, plastic, chemistry, sheet metal, medical, warehouses, electronics, equipments, pharmacy ...
|
|
Vacuum lifting with an INDEVA means more productivity, more ergonomics, mre safety.
Scaglia INDEVA offers the most complete range of industrial manipulator on the market, including both traditional pneumatic manipulators and state of the art electronic manipulators, better referred to as INDEVA.
Pneumatic manipulators are ideal to handle offset loads while Indeva are ideal anywhere speed, fluid movement and exact positioning of the load are required.
|
|
Pneumatic arm manipulator with handling attachment for single tubes or tubes assembly.
180° rotating device by pneumatic motor.
Max capacity 280 kg.
Max work radius 3.7 m.
Max vertical stroke up to 2100 mm.
|
|
Scaglia INDEVA offers the most complete range of industrial manipulator on the market, including both traditional pneumatic manipulators and state of the art electronic manipulators, better referred to as INDEVA.
Pneumatic manipulators are ideal to handle offset loads while Indeva are ideal anywhere speed, fluid movement and exact positioning of the load are required.
|
|
Vacuum lifting with an INDEVA means more productivity, more ergonomics, more safety! Specialists in vacuum lifting and material handling solutions since 1975.
Scaglia INDEVA offers the most complete range of industrial manipulator on the market, including both traditional pneumatic manipulators and state of the art electronic manipulators, better referred to as INDEVA.
Pneumatic manipulators are ideal to handle offset loads while Indeva are ideal anywhere speed, fluid movement and exact positioning of the load are required.
|
|
Handling attachment for natural rubber. Indicated for the movement of parts having a very rough surface.
Vacuum generation by electric vane pump.
Max capacity 140 kg.
Accessories: quick disconnection for suction pads, angular adaptor, flexible extended manouvre handle, etc.
|
|
Pneumatic arm manipulator with pneumatic gripping tool for cloth, paper or plastic rolls.
180° rotating device by pneumatic motor.
Max capacity 280 kg.
Max work radius 3.7 m.
Max vertical stroke up to 2100 mm.
|
|
Pneumatic arm manipulator with vacuum pads handling attachment, with 4 x 90° manual rotation, equipped with inclination adaptor for unloading of sealing machines
Max capacity 280 kg.
Work radius up to 3,7 m.
|
|
Pneumatic arm manipulators for handling, “weightless”, which allows the minimum effort for the operator. Designed on the principle of the pantograph allows the operator to work inside an area, with rectangular shaped section, defined by the minimum and maximum work radius and the vertical stroke.
Max capacity 250 kg
Max work radius 2,9 m
Vertical stroke 1,98 m
|
|
FAMATEC FRIENDLY is a “standard” solution for specific applications with common requirements. User-friendlyness, unique design and extreme detail care are the key points of FAMATEC Friendly success.
All the solutions from our brands have as common factors the highest care in details and the will to be recognized as product-leader for the quality of the service offered.
|
|
The most advanced manipulator
A rigid manipulation principle is often desirable for eccentric handling (loads that can be handled centrically are best manipulated using a flexible or self-suspended principle such as a cable balancer). The most advanced possibility in rigid handling systems is the Master Balancer: because, in this case too, the arms are bare and hollow. So that manoeuvrability is much better than with conventional manipulators which have drive elements and sometimes even ballast weights on the arms, which means that everything moves. (For technical specifications: see table below)
|
|
Pneumatic arm manipulator with pneumatic expander for bobbins.
Thanks to the quick connection of special adaptors, it is possible to handle bobbins with the internal hole from 76 to 200 mm or more.
90° tilting device by pneumatic actuator.
Max capacity 280 kg.
Max work radius 3.7 m.
Max vertical stroke up to 2100 mm.
|
|
The most advanced manipulator
A rigid manipulation principle is often desirable for eccentric handling (loads that can be handled centrically are best manipulated using a flexible or self-suspended principle such as a cable balancer). The most advanced possibility in rigid handling systems is the Master Balancer: because, in this case too, the arms are bare and hollow. So that manoeuvrability is much better than with conventional manipulators which have drive elements and sometimes even ballast weights on the arms, which means that everything moves. (For technical specifications: see table below)
|
|
FAMATEC FRIENDLY is a “standard” solution for specific applications with common requirements. User-friendlyness, unique design and extreme detail care are the key points of FAMATEC Friendly success.
All the solutions from our brands have as common factors the highest care in details and the will to be recognized as product-leader for the quality of the service offered.
|
|
Pneumatic manipulating model Standard with tool of taken to magnet
Description
The standard solutions allow to head at the certainty of the repetitive and optimized solution as from the numerous solutions supplied on similar demands. FAMATEC Standard offers to perfectly definable times of delivery and a precise definition of the technical aspects in phase of offer.
Technical details
In the event specific draft of a manipulating to snodati rigid arms equipped of vertical movement of raising to double rope. The solution can be used for the movimentazione of all those products that can be raised through a magnet (in the event illustrated windings).
The product can be raised and moved on the horizontal plane in every point inside of the workspace.
The illustrated solution is mounted on a fixed column but it can be had also in the configurations to column, on autostabile base, hanging and flowing (also with system to bridge-laying tank).
Capacity 200 kg
Range 2500
|
|
|
|
|
|
Loader seeds automatic rifle for sticks of paper for the line of feeding of a rotating one of press.
Semi-automatic loader for sticks of paper FOR the line of feeding of a rotating one of press.
It is equipped of a system of taken to pneumatic clamp opportunely sagomata and determine the proportions, joined to a balancing system automatic rifle of the cargo installed on an articulate arm or the flowing ways of race to carroponte.
It is used with nature acting on the commando console who is studied in order to guarantee ergonomics and operating rapidity; 4 sticks are loaded medium with paper to the minute.
The taken clamp of is constituted from two thin ganasce sagomate flowing ones for the taken one on the short side of the packages of paper; the wide faying surface of the ganasce avoids that the ream of paper is damaged on the flanks for effect of the serration force.
The commando console is Friendly, with prati push-buttons to us of dual-control for the drive of the clamp avoiding crushings or traumi to the limbs.
The balancing body of the machine works to compressed air 7 bars (0,7 mPa), is of highest reliability and duration in the time.
It can be installed in three various configurations:
on a double mounted articulate arm on a fixed column
on a double mounted articulate arm on a fixed column to a autostabile platform
on aerial flowing track on axis X or to carroponte on the aces X and Y.
It works to single compressed air, is marchiato CE and it is not subject to the safety controls of the raising systems.
|
|
Pneumatic manipulating model Standard with tool of taken for movement bags
Description
The standard solutions allow to head at the certainty of the repetitive and optimized solution as from the numerous solutions supplied on similar demands. FAMATEC Standard offers to perfectly definable times of delivery and a precise definition of the technical aspects in phase of offer.
Technical details
In the event specific draft of an endowed manipulating of a system of taken flowing along the revolving and equipped arm of vertical movement through a detail is arranged of raising of the product. The solution is the ideal for who must enliven similari bags or products quickly (as an example scato them). The taken one happens through a ventosa and successively the product can be raised and moved on the horizontal plane in every point inside of the workspace.
The illustrated solution is available on autostabile base and fixed column.
The maximum capacity 65 kg
Range 4000 milimeter
|
|
All solutions FAMATEC are programmed to be prepared in these various configurations, while guaranteeing moreover, the possibility of reconfiguring the solution thereafter during an evolution or of a change of the requirements of the Customer.
The suspended configuration adapts to mediums characterized by a place of limited operation in which there is a need for working under good conditions and in perfect safety
|
|
|
|
