|
|
|
Abrasive cut-off saws, 7" -30" diameter blades, dry cut and Wet cut available, special design machines also available. Please contact factory for pricing.
|
|
SUPER TECHNICS 350
Manual circular saw, robust, fast and precise cutting of metal profiles and solid materials: for professional use in maintenance workshops and low duty production.
Optional sawdisc diam.350 mm.
Two ways miter (from 0° to 45°) and longitudinal cutting.
Three cutting speeds.
Quick lock vice with anti-burr clamping.
Mobile countervice.
Sawdisc breakage protection with safety clutch.
|
|
The C300 Series cut-off machines originate from the technological development of the C250 Series. In addition to the basic features which are common to both Series, the two C300 models can accomodate cutting wheels up to 300mm diameter, and have a more powerful and sophisticated motor, controlled by a frequency inverter. The main function of the frequency inverter is to electronically control the motor power variations during the sample cutting process, improving the performances. Moreover, the inverter acts as a motor brake in case of power failure (caused, for example, by the safety switch that immediately interrupts the power supply in case the cover is open while the machine is working), allowing the complete stop of the motor in a shorter time than a machine not equipped with the inverter.
The difference between the two models of the C300 Series is the variable speed device, which is available only on the C300VS cut-off machine.
|
|
Manual sawing machines using an HSS circular blade to cut metal solids and sections up to 120 mm diameter from 45° SX to 45°DX
|
|
2300 Watt Metal Chop Saw CS 23-355
For single phase alternating current
Especially suitable for the fast, precise cutting of steel, non-ferrous metals, iron and cast profile
Motor and gear with ball bearing and designed for high loads
Spindle lock for easy disc change
Quick clamping device with variable mitre conversion up to 45° on both sides
Easy to transport due to built-in handle and locking device
Swivelling blade guard
Adjustable spark guide plate
Bottom access guard
Adjustable depth guide
|
|
250 mm (10") H.S.S. sawblade
cuts steel, stainless steel, nonferrous metals
head miters 0°- 45°
vise opens 105 mm (4.1")
pull-out coolant tank
2-piece safety guard
|
|
Oil-bath lubricated gear
Safety clutch prevents gear or blade breakage if an overload occurs (exception KKS 250)
Integrated coolant tank
Head swivels 45° to the left and to the right
KKS 250 / 315 - base included
|
|
As the leading manufacturer of machines for processing aluminium and PVC profiles, we supply matured solutions for different applications.
You have profile - we cut it !
Further saws, like Table saws, Mitre saws, Double mitre saws, Notching saws, Vee-notch and cut off saws, Automatic saws and Automatic saws with pusher cover our product range.
|
|
| ... products without technical information |
| |
Separator® Cutoff Tools
Maximize your productivity and lower your cost per cut with Separator® quality and variety.
- Separator® Classic Inserts
- Separator® F2 Inserts
- Separator® G2 Inserts
- Separator® S2 Inserts
- Separator® S2-Ultra Inserts
|
|
|
Thermtrol’s Thermal Cutoffs, also known as One Shot Thermal Fuses, inexpensively open a circuit when a predetermined set temperature is reached. Cutoffs covering a temperature range of 66C to 240C are stocked. Available in both radial or axial lead configurations, Thermal Cutoffs have current ratings from 1/2Amp to 15Amps and are UL, VDE, CSA agency rated for 50VDC, 120VAC, and 250VAC circuits. The large in-stock inventory and infinite customization options permit quick turn-around of drop-in devices. Thermtrol Corporation…Your Partner in Thermal Protection!
|
|
LEFON Stainless Pipe Cutting Saw / orbital saw, ideal for cutting Stainless Steel Pipe / Tube . Four model available, R4,R6,R8 and R12
R4, working range: pipe OD:1/2"-4", pipe wall thickness: 1 - 7mm
R6, working range: pipe OD 3"-6", pipe wall thickness: 2 -10mm
R8, working range: pipe OD 6"-8", pipe wall thickness: 2 -10mm
R12, working range: pipe OD 8"-12", pipe wall thickness: 2 - 10mm
Key advantage of this orbital cutting machine:
* Burr-free
* Multipoint clamping to eliminate pipe deformation
* Easy to operate
* Precise square cutting
* Cutting and Beveling simultaneously
* Highly reliable, long working life
Applicable to the following material:
* Alloy Steel Pipe (e.g. stainless steel)
* Carbon Steel Pipe
* Non-ferrous Metal Pipe
* Plastic Pipe
* Casting Iron Pipe
* Highly reliable, long working life
|
|
Pipe cutter SUPERCUTTER available with pneumatic
or hydraulic motor.
Upper locking jaws are marked with workable
pipe diameter for easy and quick machine set
up onto pipe.
The unit is equipped with two copier toolboxes
for following the pipe od profile, thus minimizing
the bevel offset due to out of round of pipe.
|
|
| ... products without technical information |
| |
DCS3410TH
Chain Blade, Guide Bar Cover, Chain Cover, Wrenches
FEATURES
Sealed tank system.
Allows professional and safe working in combination with climbing harnesses and hydraulic lift platforms.
Optimum Vibration damping.
Fast acceleration and low emissions.
Easy, uncomplicated starting.
|
|
|
The easy to manage, compact and light portable chain saw for small openings, breaking-through in concrete or masonry.
|
|
Sandvik Coromant’s new GC1125 grade lives up to the demands of the leading parting and grooving tooling system, CoroCut® 1-2 edge and is now the first choice to achieve improved performance in parting, grooving, turning and profiling operations in a wide geometry range.
The optimization of properties for this grade delivers a wider application area and the capacity to handle improved cutting data. GC1125 has a good all round ability and provides the means to improve performance in a wide geometry range across many parting, grooving, turning and profiling operations. It is the first choice for application in steel and stainless steels and excels when machining cast iron and HRSA materials.
These advantages result from a technological breakthrough in coating and substrate technology. The combination improves wear resistance and security, either when running at higher cutting speeds or for a longer time in cut. The coating is new, PVD with TiAIN layers, including properties designed for the GC1125’s wide application area. New, fine grained substrate optimised for steels and stainless steels has improved hardness and supports increases in cutting data.
GC1125 is a simpler option, enabling machine shops to do more with one grade. Its wide geometry range offers improved performance to a larger number of machining operations.
In parting, it is optimised for steels, stainless steels and HRSA materials, a first choice in CF and CR geometries. CF is the low feed choice, giving excellent chip control and surface finish, CR the strong geometry for parting off bars and interrupted cuts at high feeds.
|
|
ISCAR-GRIP
Parting Inserts
DO-GRIP
First choice for parting. Double-ended inserts. Self clamped for deep grooving and large diameters. Screw clamped for small diameters.
SELF-GRIP
Single-ended insert for deep grooving and large diameters. Has a stopper for high radial accuracy.
CUT-GRIP
Single-ended insert. Self and screw clamped options. For tool users.
DO-GRIP for Swiss Automatics. The most economical, double-ended parting and grooving inserts in 1.0 - 3.0 mm (.039 - .118") widths that can be mounted on small shank 8, 10, and 12 mm (.315, .394, and .472") holders. The new design has a very short clamping head and with a slanted screw for convenient
indexing. These features are essential for operating on Swiss type automatic machines that have very limited space.
DO-GRIP is an optimal solution for grooving and parting of small shafts and tubes.
|
|
Sandvik Coromant is now extending its premium program of cutting tools for parting and grooving which will, no doubt, have great influence on machining productivity.
CoroCut 3 brings a third cutting edge to the shallow parting of tubes, bars and grooving operations. The extremely small parting widths in 2,0, 1,5 and 1,0 mm facilitates will reduce the raw material usage considerably.
The insert is held securely by a unique clamping solution ensuring accurate location and easy to use. This in combination with very tight indexing tolerances will produce workpieces with very close length tolerances.
Two dedicated insert geometries ensure peak performance and excellent surface finish in all workpiece materials. The very same holder can be used for all insert widths giving maximum versatility.
|
|
|
|
see the results for the following category
