|
|
Stone Hammer Blow Testing Instrument acc. to VDA, MULTI GRIT TESTER 508 MC
A multi-blow test instrument developed in association with the automotive industry, offering outstanding reproducibility and comparability of results. The pressure accumulator dampens variations in the compressed air mains. Supply of shot particles adjustable.
|
|
Tensile and Pressure Testing Machine UNIMAT® PLUS 050 - 2 kN
Tensile and Pressure Testing Machine UNIMAT® PLUS 052 - 5 kN
Electrically driven testing machine, consisting of: Testing machine frame with driving unit, a displacement measurement, and an integrated evaluation and control unit based on PHYSIMETER® 906 MC-E. In the standard version the evaluation unit is provided with an wire strain gauge input for sensors (nominal signal 1 mV/V to 2.2 mV/V), an analogue output (± 2.5 V) and an encoder input. These three measuring channels represent the necessary basic configuration of the evaluation unit. Via data cable to be ordered separately the measured data can be transmitted to a PC.
The Measuring and Evaluation Software PHYSISOFT II is available free of charge at www.erichsen.de/download.
|
|
SANTAM Universal Testing Machine is used for industrial quality control laboratories and research centers. The machine is able to test the mechanical properties of a wide range of the materials such as:
Metals Casting Sheet & Foils Graphits
Plastics Welding Bars & Belts Adhesives
Ceramics Wire & Cable Rubber Automobile Components
Composites Tube & Pipe Timber Finished Components
With additional accessories, the following test can be performed:
Tension Shear Ring Stiffness
Compression Flexure Foam Hardness
Bending Stiffness Creep
Peel Buckling Relaxation
Main Specifications:
- Capacities: 5, 20, 50, 150, 400, 600 & 1000 KN
- Operation: Servo electro mechanical (Precision ballscrews and Servo Drive System)
- Load Mode: Tension, Compression, Cyclic, Step, Creep, Relaxation & Hardness
- Load Control: Speed, Position, Force, Strain & Stress control
- Speed Range: 0.001 mm/min ~ Nominal speed (200~1000 mm/min depends on machine capacity)
Load Control
- Load measurement: Resolution : 1/200000 of load cell capacity ,Accuracy: 0.5% of reading from 1/250 ~ 1/1 of loadcell capacity
- Extension Measurement: Resolution: better than 0.00003mm, Accuracy: 0.03mm on 300mm
- Accessories: Different types of Load cells, Extensometers, Grips & Fixtures based on different applications and kinds of materials.
|
|
Lacquer and Paint Testing Machine, Model 202 C
Version with electro-hydraulic drive for coated sheets up to 1.5 mm thick. Infinitely variable control of drawing speed up to 50 mm/min. Automatic clamping of specimen. By virtue of the C-form test head aperture it is possible to test sheet metal panels in addition to sheet metal strips.
Option:
Camera module VIDEOMASTER USB comfortable observation of the deep drawing process or stereo microscope.
|
|
Instron's line of torque testers extends Instron's materials testing solutions by providing dependable torsion and axial-torsion testing capability.
These torsion testers utilize the familiar 5500 and 8800 electronics you've come to rely on. Available in capacities from 12 Nm (100 in-lb) through 13,000 Nm (120,000 in-lb) these test frames are versatile and easy-to-use for many applications including biomedical, automotive, aerospace and other industrial and consumer products.
The 55MT Series is a family of two table-top torsion testers.
55MT1 offers a 22 Nm (200 in-lb) capacity
55MT2 offers a capacity of up to 220 Nm (2,000 in-lb)
The 55MT Torsion Testers are based on a dual linear slide design, which provides for high torsional stiffness and minimal axial friction. The system torque cell is attached to a movable crosshead, which can be left free floating or clamped during testing. When left free floating, the user can apply an axial pre-load to the specimen using a weight and pulley arrangement. Closed loop servo control of the electromechanical drive is provided by Instron's standard 5500 electronics and Partner torsion software.
|
|
Features
- High Accuracy and Repeatability
- Wide Range of Materials Testing
- Enhanced Control Panel
- Easy - to - Use
- Computer Control and Enhanced Software
- Modular Design
- Interchangeable Load Cells, Grips and Fixtures
SANTAM Universal Testing Machine is used for industrial quality control laboratories and research centers The machine is able to test the mechanical properties of a wide range of the materials such as:
Plastics, Rubber, Metals, Composites, Textiles, Yarn, Wire, Timber, Adhesives, Paper, Foams, Foils, Food, Film, Graphite, Finished Components
With additional accessories , the following test can be performed:
Tension, Compression, Bending
Peel, Shear, Flexure
Stiffness, Buckling, Ring Stiffness
Creep, Foam Hardness, Relaxation
|
|
Universal testing machines SATEC Series kN
Planned for tensile the tests, compression, folding/inflection and shearing with high capacity, the design of models kN gets height as regards adaptability.
Characteristics
The space of single test ultra-broad can receive a range of sizes of test-tube, jaws, fixings, furnaces and extensometers.
High speeds of test and the long useful race make it possible to adapt to various conditions of test.
The electronics of numerical control ensures a high precision and the speed of answer. The integrated controller recognizes and calibrates automatically the sensors, thus eliminating the switches, the potentiometers and the dials.
The choice of the universal software of tests Partner™ material; or Bluehill® 2 ensures the height flexibility facility of use.
The hydraulic jaws with side action standards facilitate the loading and the unloading of the test-tubes.
|
|
|
The universal testing machines of Instron make it possible to test in traction and compression on the same frame. Moreover, some built permit the tests of constraints reversed. The tests can be of the traction type, compression, shearing, inflection, peeling, tearing, cyclic and inflection.
|
|
The systems of tests of table of Series 5860 are appropriate ideally for the tests of force lower than 50 kN requiring a precise alignment or to test the large test-tubes. These systems use the electronics of acquisition and the most powerful order and the software Bluehill® 2 standardized in industry. Compared to the systems monocolonnes, the design bicolonne improves alignment and increases rigidity. These systems can be equipped with a vast range with jaws and accessories for the inflection, compression, tensile tests and component. The accessories available include/understand extensometers for the measurement of the deformations and the climatic chambers for the tests at varied temperatures.
Characteristics
Very high degree of accuracy: + 0.4% of the posted load (up to 1,0% of full capacity)
Very broad beach: Measurement bracket of force 500:1 (use of the sensor of force up to 0,2% of its capacity without loss of precision) with + 0.5% of the posted load
Precision of load +-0,5% of the posted load
High-speed acquisition of the data: 5000 Hz, synchronous on all the channels
Manual control panel studied for the operator well-being
Automatic recognition of the sensors of force and the extensometers
Compatible with the software Bluehill® 2 and FastTrack for 5800
Exist in extra-high and extra-broad version
The second space of test in option
Library of testing methods ASTM and ISO
Open architecture for programming of personalized tests
Total conformity with label EC
|
|
- Split Drum Mechanism for destruction testing of synthetic flat bed materials
- Hold material up to 300mm wide
- Maximum capacity 75 tonnes
|
|
Rope Grip Wedge Box
- Available for all machines up to 200 tonne capacity.
- Suitable for most materials.
- Grips smooth surfaces eg. Wire Rope, Synthetic Nylon & Aluminium Conductor Cable.
- Grips material without damage & can be used through to destruction on rope.
- Easy to use mechanism. Self releasing when load is dispersed
- Supplied with 10 varying sizes of inserts to suit application.
|
|
|
The LHPU is a catalyst testing station, used to characterize reforming catalysts, shift catalyst, prox catalysts etc. It is a suitable device for using in the development of hydrogen and fuel cells solutions. Users typically are R&D departments of OEM's, R&D centres, Universities, Fuel cell companies and Catalyst manufacturers.
|
|
| ... products without technical information |
| |
|
|
