|
|
Maximize your productivity and lower your cost per cut with OTM™ quality and variety.
END MILLS
Small Diameter End Mills
Small Diameter End Mills – Single Flute INCH
Small Diameter End Mills – Two Flute
Large Diameter End Mills – Single Flute
Large Diameter End Mills – Two Flute and Three Flute
Extended Length End Mills
Long Edge End Mills
|
|
Particularly suited for High Speed Machining (HSM) and precision milling operations often associated with aerospace and die and mould applications.
The range covers milling operations in aluminium and thermoplastics - slotting, contouring, 3D forming, deep pocket milling and profiling; from roughing to finishing and “super-finishing”.
|
|
High Performance "HELICAL" PCD End Mill.
The new helical design is very well suited for carbon fiber and aluminum material.
The new innovative end mills are available in 2, 3 and 4 flute design. These PCD end mills can be tailored to specific applications with regard to Carbide and PCD grade selection. As a result, increased feeds and speeds, enhanced work piece finish and extended tool life is realized.
|
|
- Premier cutters for high-performance, line-by-line finishing milling.
- Rough, semi-finish, and finish with one tool.
- Highly accurate -- axial runout of ± .0004"; radial runout of ± .0001".
- Three insert geometries for light, medium, and medium-heavy applications
|
|
|
|
|
|
GRATEX I - HSSCo
* For taps according to DIN 371 (2 teeth / angle 90°)
For deburring and chamfering of tapped holes if using a tap according to DIN 371 with angles of 90 degrees.
* For taps according to DIN 371 (2 teeth / angle 120°)
For deburring and chamfering of tapped holes if using a tap according to DIN 371 with angles of 120 degrees.
* For taps according to DIN 371 (3 teeth / angle 90°)
For deburring and chamfering of tapped holes if using a tap according to DIN 371 with angles of 90 degrees.
* For taps according to DIN 371 (3 teeth / angle 120°)
For deburring and chamfering of tapped holes if using a tap according to DIN 371 with angles of 120 degrees.
* For taps according to DIN 376 (2 teeth / angle 90°)
For deburring and chamfering of tapped holes if using a tap according to DIN 376 with angles of 90 degrees.
* For taps according to DIN 376 (2 teeth / angle 120°)
For deburring and chamfering of tapped holes if using a tap according to DIN 376 with angles of 120 degrees.
* For taps according to DIN 376 (3 teeth / angle 90°)
For deburring and chamfering of tapped holes if using a tap according to DIN 376 with angles of 90 degrees.
* For taps according to DIN 376 (3 teeth / angle 120°)
For deburring and chamfering of tapped holes if using a tap according to DIN 376 with angles of 120 degrees.
|
|
PRIMAX ROUGHING CUTTERS
* Reduced tool vibration, means a smoother cutting operation and less chipping on the tool itself.
* This also leads to an improved surface finish on the component being machined.
* Less wear on the teeth results in longer tool life.
|
|
Solid Carbide End Mills From the Industry Leader
SGS Tool Company offers a wide variety of end mills for just about any application. From standard end mills to long, short, double end, high spiral, roughing, miniature and more...you'll find what you need right here. And with 12 sales and warehouse facilities in Europe, Asia and North America, chances are it's in stock and ready to ship out to you.
For Maximum Stock Removal in Milling Operations on Mild Steel, Steel Alloys, Stainless Steel and Cast Iron...Fractional and Metric.
|
|
Square End Mills - Roughing and Semi-Finishing
* Maximum metal removal rates in slotting, profiling, and pocketing on any surface finish.
* Fewer passes needed in heavier cuts.
* Light finishing pass with multiple-flute tool achieves final surface finish.
* Big savings in machining time with material-specific profiles designs.
|
|
Square End Mills - Finishing
* Available in 2- and 3-flute styles for slotting and pocketing.
* Multiple-flute styles for profiling and finishing in hard materials.
* More flutes, higher feed rates, more rigid tools, good chip removal.
|
|
Solid carbide endmills DS
Solid carbide milling cutter for
- steel (soft and hard),
- copper,
- graphite,
- aluminium
Cutting edge diameter from 0.2 mm
Full radius, torus, micro, end, roughing and double radius mills
|
|
The Leading Edge in Burs
There are burs and then there are SGS burs. SGS Tool Company is the world's leading bur manufacturer. No one manufactures or sells more burs than SGS...and no one else offers a more diverse line of burs and a familiarity with your challenges. SGS burs are ideal for a wide variety of applications, including:
Foundries & Castings:
Safe, effective, consistent and comfortable performance
ideal for applications from handheld to robotic.
Mold & Die:
Ability to handle difficult workpiece materials and an array of shapes,
sizes and precision required for tight tolerance applications and superior finishes.
Turbine Manufacturing and Repair:
These applications are often performed on materials with poor machinability properties and, as a result, have a negative effect on tool life and performance. SGS has developed burs to address the demands of this industry.
|
|
Series 46J, 46D, 47J, 47D, 48D Solid Carbide Tip End Mill
45 Degree Helix, Center Cutting, High Precision, Grade IN2005
Diameters:
.312" and .625"
Cutting Edge Length:
.20" and .47"
Cutting Edge Radius:
Sharp, .015", .030", and .060"
|
|
|
DIXI Polytool has a wide range of standard end mills, ball nose end mills, end mills with corner radius, chamfering tools and end mills for composites. The ranges of Ø start at 0.05mm.
|
|
When your non-ferrous application requires contour or
3-D work, the ARF-BN series is the tool of choice. We
combine the proven geometries of our ARF series with a
precision ground full ball radius. The higher helix and
clearance angles provide a freer cutting ball with
advanced shearing properties. Stub and regular flute
lengths with material specific coatings are all in stock.
|
|
Corner Rounding End Mills
FAST BREAK Series 15R1V and 15R4H
TOP ON mini_15r4h_topon
FAST BREAK PAKS Series 15R1V and 15R4H
|
|
V400 Finishing Ball Nose End Mills
The V400 finishing ball nose end mill brings greater accuracy and size control to contour milling. Ultra-precision ground inserts in a new, highly versatile PVD coated grade, VP5007, result in superior finishes and greater accuracy on a wide range of materials. Advanced insert technology combined with advanced cutter design makes the ValMILL 400 a superior performer in the die and mold industry, and a reliable producer wherever high quality machining is needed.
|
|
|
|
|
|
WELDON 2AR-BN:
Our 2AR-BN is designed for roughing non-ferrous materials where the application demands a high metal removal rate.
We have combined a high-shear, 40 degree helix with a cylindrical margin for chatter resistant, smooth machining in all non-ferrous materials.
The 2AR-BN is available from stock as a bright tool or with Zirconium Nitride (ZrN) and Titanium Carbonitride (TiCN) coatings for improved performance and extended tool life. Special quotes and non-stocked coatings are available upon request.
WELDON 4SR-BN:
Our 4SR-BN tools have the same full eccentric primary grind, and 40 degree flute helix as our 3SR series. We have added a fourth flute to this proven design to provide up to a 30%+ increase in metal removal rates for those operations that demand higher levels of productivity in steel and ferrous alloy roughing.
Our 4SR-BN is stocked with Aluminum Titanium Nitride (AlTiN) and Titanium Carbonitride (TiCN) coatings in stub and standard lengths. Special quotes and non-stocked coatings are available upon request.
|
|
carbide rotary burr
3210V Standart - cut cross - tooth cylinder
3211V Double-cut cross - tooth ball - nose cylinder
3212V Double-cut cross - tooth end - nose cylinder
3213V Cross-tooth ball - shape nose cylinder
3214V Cross-tooth oval nose cylinder
3215V Cross-tooth round-nose tree nose cylinder
3216V Cross-tooth round-nose tree nose cylinder
3217V Cross-tooth round-nose tree nose cylinder
3218V Cross-tooth round-nose taper nose cylinder
BOX : 5 pc carbide burr kit
|
|
Main Features
- Incredible high feed speed 2,000 mm/min in grooving.
- High speed and high quality surface of workpiece.
- Useful in dry milling
- Wider application in work material.
|
|
Series 46J, 46D, 47J, 47D, 48D Solid Carbide Tip End Mill
Diameters:.312" and .625"
Cutting Edge Length:.20" and .47"
Cutting Edge Radius:Sharp, .015", .030", and .060"
|
|
Jabro Tools - premium solid carbide tools
The Dutch solid carbide tool specialist Jabro became a member of the Seco Tools group in 2001. The company has a full range of high quality solid carbide tools for the Aerospace, Die & Mould as well as many other precision engineering segments. Jabro's product range is a natural extension of Seco's products.
"Completion of this transaction is of great significance for Seco and part of the continuous process to strengthen Seco's competitiveness within important markets and customer segments," says Lars Renström, President and Chief Executive Officer of Seco Tools.
With 120 employees Jabro is among the leading companies in the product area solid-carbide end mills - a fast-growing area primarily focused on the aviation and die and mold industries. Through this acquisition, Seco Tools expands its product offering to customers, thereby strengthening its competitiveness in serving the above-mentioned customer segments.
|
|
|
|
|
|
SOLID CARBIDE END MILLS:
Our micro-grain carbide substrate offers excellent hardness, wear resistance and high strength. These tools can provide increased feeds and speeds and enhanced tool life in applications that have rigid set-ups.
HIGH SPEED STEEL END MILLS AND MISCELLANEOUS CUTTERS:
We offer a variety of general purpose and special application end mills and cutters that have been designed to ANSI and NAS specifications in our high speed steel grouping. These tools are made from a substrate that offers very good abrasion resistance for wear and red hardness at higher milling
temperatures than other high speed steels.
COBALT END MILLS:
Our cobalt grouping also offers tools that meet the ANSI and NAS specifications and have been designed for general purpose and special applications. The 8% cobalt substrate in these tools allows a higher hardness, which provides better abrasion resistance and higher red hardness benefits, versus standard high speed steel substrates.
POWDERED METAL END MILLS:
Powdered Metal tools provide a bridge between cobalt tool performance characteristics and carbide tool performance characteristics.
ROUGHING / FINISHING AND ROUGHING END MILLS:
These tools are capable of high metal removal rates while producing a finish which is usually equivalent to that produced by conventional finishing end mills. The roughing/finishing end mills are offered with different application specific substrates and specialized cutting geometries to maximize material removal.
|
|
|
DIXI Polytool has a wide range of standard end mills, ball nose end mills, end mills with corner radius, chamfering tools and end mills for composites. The ranges of Ø start at 0.05mm.
|
|
Whether it’s your design, or one with which we assist, Data
Flute CNC is your source for special application cutting tools.
We will put our years of experience to work for you when
manufacturing the specific tool that you need.
From special diameters or geometries to tapered ballnose
to form cutters, Data Flute CNC should be your choice for
specials. Please give us a call or fax in a blueprint. We’ll be
glad to help.
|
|
- Most Ferrous, Non-Ferrous and
- Non-Metallic Materials
- Plunge and Ramp
- Profile, Slot and Pocket
- Micrograin Solid Carbide
- Center Cutting
- Plain Round Shank (*Weldon Shank)
- High Rigidity from Substrate
- Optimum Speeds and Feeds
|
|
Ideal for roughing applications
Hi-Pos APKT16 series nose stations have been upgraded to more robust and free-cutting Hi-Pos+ AOMT18 series
Available with 3 different shank styles, as well as in a custom engineered weldon-style shank that draws the cutter into the holder
|
|
WMM End Mills
* Performs slotting, ramping, pocketing, drilling, shoulder milling, and helical boring operations
* Available in 1.00"- 1.50" cutter diameters
* Employs the same APMT/APET inserts as the WEM and WRM
* Staggered peripheral inserts decrease cutting forces
|
|
The ALDH is the rougher of choice when optimum
material removal rates are the objective. The combination
of progressive geometries result in a cutting tool intended
for full engagement cuts at increased feed rates.
Slotting cuts of 1x the diameter or more are normally
recommended. 50% greater IPM vs. competitors 2 flute
design is a conservative starting point.
|
|
DHC Roughing-Finishing End mills for highest productivity
Features
- Continous modified cutting edge pitch
- Stable cutting edge geometry with micro cutting edge preparation
- Optimized chip space
- Tough micro grain carbide grade
- Wear resistant and temperature stable PVD coating AL 2 Plus
Benefits
- Higher feed rates
- Higher depths of cut
- Higher metal removal rate
- Roughing and finishing with the same cutter
- Less vibrations
- Better cutting dynamics
- Better chip evacution
- Good surface quality on the workpiece
|
|
|
|
