|
|
The DOPAG ELDO-MIX range of gear pump driven metering and mixing systems are built in modular form and are custom designed.
Depending on the specific application, various basic configurations are available.
|
|
The Filament Winding DL is a two-component continuous-flow programmable-ratio meter, mix, and dispense machine for filament winding. The DL will supply accurately mixed resin/hardener systems directly to in-line composite processes. It is designed to easily fit into any production layout.
Features:
- Continuous feed of premixed resin/hardener
- Precision gear metering pumps
- Touch pad programming of mix ratios and flow rates
- Choice of several tank, drum or totes feed systems
|
|
Technical Data:
-Stainless steel frame
-Switch cabinet with controler, pneumatic and mechanics
-Feed part A direct from suppliers 50 litre open topped straight sided rums, follower-plate unit with 360mm diameter
-Feed part B direct from suppliers 50 litre open topped straight sided drums, follower-plate unit with 360mm diameter
-Metering pump with drive unit mounted on follower plate A
-Metering pump with drive unit mounted on follower plate B
-Low level cut off for both components
-Three-phase current motor
-Electronic adjustable dispense rate
-Electronic mixing ratio adjustment
-Pressure lines 250 bar
-Mixing block with dynamic and static mixing
-Purge with one component
-Swivel boom for mixing block
-Follower plate unit and Unidos 300 TX/MP machine are based on a zinc plated steel base with rollers
-Potlife alarm, adjustable time
|
|
| ... products without technical information |
| |
The Filament Winding DL is a two-component continuous-flow programmable-ratio meter, mix, and dispense machine for filament winding. The DL will supply accurately mixed resin/hardener systems directly to in-line composite processes. It is designed to easily fit into any production layout.
Features:
- Continuous feed of premixed resin/hardener
- Precision gear metering pumps
- Touch pad programming of mix ratios and flow rates
- Choice of several tank, drum or totes feed systems
|
|
Technical Data:
-Stainless steel frame
-Switch cabinet with controler, pneumatic and mechanics
-Feed part A direct from suppliers 50 litre open topped straight sided rums, follower-plate unit with 360mm diameter
-Feed part B direct from suppliers 50 litre open topped straight sided drums, follower-plate unit with 360mm diameter
-Metering pump with drive unit mounted on follower plate A
-Metering pump with drive unit mounted on follower plate B
-Low level cut off for both components
-Three-phase current motor
-Electronic adjustable dispense rate
-Electronic mixing ratio adjustment
-Pressure lines 250 bar
-Mixing block with dynamic and static mixing
-Purge with one component
-Swivel boom for mixing block
-Follower plate unit and Unidos 300 TX/MP machine are based on a zinc plated steel base with rollers
-Potlife alarm, adjustable time
|
|
| ... products without technical information |
| |
|
|
|
|
Molykote® synthetic oils are produced through chemical synthesis to meet targeted performance specifications and to minimize impurities. Synthetic oils are formulated with new generation performance-enhancing additives. Molykote mineral oils are produced in a series of proprietary hydroprocessing steps, which ensures that they are nearly free of contaminants. Synthetic blends are comprised of synthetic and hydroprocessed mineral oil base stocks. All oils in this section are available in pails
and drums.
Molykote® gearbox lubricants help prevent wear and process interruptions in power transmission systems and components. Compared to conventional oils they also offer greater resistance to oxidation and stable performance at high temperatures and under high loads. Molykote gearbox oils maximize fill intervals and maintain viscosity characteristics at wide temperature ranges. Molykote gearbox oils meet AGMA 9005-E02. In addition to AGMA, Molykote L-21XX series gearbox oils also meet DIN 51 517 Part 3, US Steel 224, Flender, Cincinnati Machine, David Brown SL.53.101.
|
|
SUPRACO MPL Gears, multipurpose. Enclosed gears and loaded circulating oil, wheel and worm reducers.
ISO Grades available : 100, 150, 220, 320.
GEAR SY
|
|
| ... products without technical information |
| |
Gear Shaving Cutters. Gleason manufactures
and resharpens precision shaving cutters to
support Gleason Hurth shaving machines and
any other gear shaving machines. The
Gleason shaving cutter design is optimized
for maximum tool life.
|
|
STRAIGHT BEVEL GENERATING TOOLS
These are produced for Gleason machines, 24", 18", 12", 11" ,6" and 3" both roughing and finishing and also for Heidenreich and Harbeck machines, 15KH, 25KH, 26KH, 60KH and 75KH. These are manufactured as standard in M2 HSS, though tools in 5% colbalt steel can be supplied to order.
|
|
|
Dathan disc type cutters can be designed and produced for cutting any type of gear, internal or external, spur or helical. They can also be designed to cut splines, serrations, sprockets or other involute forms. The cutters are full form generated using the Dathan 'pass thro' method. These cutters may be manufactured with bore diameters from 10mm to 120mm or ½" up to 4", cutter diameters (pitch circle diameter) from .75"(19mm) to 10"(250mm) and can be manufactured to any world standard or to any specified requirement.
|
|
SHANK TYPE CUTTERS
These are primarily designed for cutting internal gears, splines and serrations, both spur and helical. May also be designed for externals if required. These cutters are full form generated however small the pitch circle diameter (PCD) although strength of the cutter produced is the limiting factor. The strength and rigidity of shank type cutters is greatly improved by the Dathan ribbing method and is especially advised for those of small PCD.
HUB TYPE CUTTERS
Dathan hub type cutters are designed for cutting internal components where maximum rigidity is required. Hub type cutters are recommended for cutting long face widths or for coarse pitches.
In general terms, any tooth form, face width or number of teeth that is available on a shank cutter, can be manufactured with a hub type fitting. Note: these cutters screw directly onto the spindle of the machine therefore rely on the spindle being in a good true state.
|
|
Gear Milling Cutters
- Gear Roughing Cutters
- Circular-type Gear Profile Cutters with Form Indexable Inserts
- Roughing Cutters for Rotors with Indexable Inserts
- Rotor Profile Cutters with Inserted Blades
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
