|
|
The forces which arise in industrial processes such a press-fit, punching or crimping often have implications for the quality of the final connection. Such forces can also be measured indirectly in terms of the strain occurring at the surface of the machine structure. This is often simpler than taking a direct force measurement, which requires the sensor to be built into the structure.
Kistler's new Type 9234A… strain transmitter with integral amplifier is fitted to the machine very simply by means of a single M6 screw. Thanks to its high sensitivity, accurate measurements are possible even with extremely rigid machine structures.
The robust transmitter is particularly suitable for use with presses and assembly line robots.
|
|
SCAIME offers a wide range of load cells allowing to provide the best solution for all the weighing applications.
- Capacities from 1kg to 200t
- OIML R60 approval up to 6000d
- All modes of demounting of load:
Single point
Compression
Bending, shear beam
Traction
- Different materials and degrees from protection allowing to optimize the cost ratio/performance
- Complete range Certified ATEX
|
|
An extensive range of products for the use in the process industry, covering all accuracy levels, various automation needs and communication demands.
The applications range from level control by weight, flow by weight, bulk weighing of silos, standard batching, weighing and batching of agitated vessels and batching control in parallel including recipe handling in larger systems.
- High accuracy
- Superior installation properties
- Withstands up to 100% side load
- For hard environmental conditions (IP67)
- Covers most applications
|
|
The advantages of piezoelectric sensors are particularly evident in force measurement. Robust and overload-proof, they are capable of resolving the smallest changes in force, even with high preload.
|
|
Series 1515 Automotive Brake Pedal Effort Sensor for Vehicle Brake Development, Drivability & Handling, & Legislative & Safety
- Designed to measure force required to operate vehicle’s primary brake,
clutch, or floor-mounted emergency brake pedals
- High overload protection (500% of FS)
- Easy to install and remove
- Integral Cable; integral loading surface to reject off-axis loading errors
- Compact Design 1.19” (3.02 cm) overall height
- Temperature-compensated for +30 to +130 °F (-1 to +54 °C)
- Good resolution, linearity and repeatability in both static (constant force)
and dynamic (panic stop) loading events.
|
|
Sensors of industrial weighing in shearing, entirely welded stainless and seals IP68.
Sensor 3510 is especially used for applications of weighing on hoppers, plates of weighing, and applications of measure of force.
Exist of 300 kg to 5000 kg with homologation IOLM in 3000 divisions
|
|
Sensors of industrial weighing in inflection, entirely welded stainless and seals IP68.
Sensor 355 is especially used for applications of weighing on hoppers, plates of weighing, machines of conditionings and applications of measure of force. Exist of 5 kg to 250 kg with homologation IOLM in 3000 divisions
|
|
Sensor 220 stainless and entirely welded IP68 is used with the assembly "Mount Silo" for the weighing of silos and hoppers of strong capacities.
Exist of 5000 kg to 50.000 kg with homologation IOLM in 3000 divisions
|
|
In the field of FORCE measurements AEP transducers offers a complete range of load cells from 10 N up to 1000 MN with precision classes varying from 00, 0.5 and 1 according to the ISO 376 norm.
Inside the range there are two main families :
The first-line-sample dynamometers dedicated to the calibration of material testing machines, test benches with high metrological characteristics also used like transfer samples on occasion of international comparisons among accredited laboratories and National Metrological Institutes.
The dynamometers dedicated to the automation in general, directly mounted on material testing machines or test benches allow to measure both static and dynamic forces in compression as well as in tension with a long term stability and reliability.
On request all the dynamometers can be supplied complete with SIT certificate issued by our accredited Metrological Laboratory.
|
|
Measurement Specialties enables OEMs to measure force using low cost Microfused™ load cells. Five configurations are currently available, with customization offered for high volume applications. Measurement Specialties also offers packaged load cell assemblies for test and measurement applications that require high performance or unique packaging. For dynamic impact applications such as industrial stamping or ballistics, our Piezo Film provides a reliable way to measure force up to thousands of pounds.
|
|
|
Strain Measurement Devices provides a seemingly infinite variety of sensors to accurately measure force, pressure, acceleration, and other physical parameters. Approximately 90% of SMD products are custom designed, these sensors meet the more specialized needs of OEM’s.
|
|
Extensometer 178 of Vishay Nobel was especially developed for the applications of level weighing and monitorings on existing or new silos of a few tons to several hundred tons.
Extensometer 178 is a gauge sensor of extensometry which transforms a mechanical deformation of the foot of the silo according to the weight into an electrical signal (mV/V) directly proportional to the load applied to the foot of the silo.
This sensor has many advantages:
Easily plantable on existing silos
No major modifications
Control nonintrusive level
Measuring accuracy from 1% to 4% of the Payload
Very good alternative to the traditional weighing of the silos
Directly exploitable signal of measurement by electronic standards for gauge sensors
Very Quality positive ratio/Price
|
|
Utilising many years of load cell and transducer design and manufacturing experience, Flintec is able to provide a custom strain gaging service on customer supplied components. From low volumes through to serial production, Flintec can provide a cost effective and reliable service to OEMs.
For customers requiring solutions to force measurement problems, Flintec is able to supply custom designed and manufactured load cells, transducers, application parts and electronics or even complete sensing solutions.
Flintec provides
- Sensing element design - CAD, FEA and 3D solid modelling
- Production of prototypes - in-house CNC machining and heat treatment
- Strain gage installation - modern, well equipped production facilities
- Calibration - temperature calibration and force calibration using hydraulic and dead weight test machines
- Electronics - internal or external signal conditioning electronics
- Rapid turnaround - all processes under one-roof
- Design verification and validation - tailored to meet the needs of the client
|
|
Utilising many years of load cell and transducer design and manufacturing experience, Flintec is able to provide a custom strain gaging service on customer supplied components. From low volumes through to serial production, Flintec can provide a cost effective and reliable service to OEMs.
For customers requiring solutions to force measurement problems, Flintec is able to supply custom designed and manufactured load cells, transducers, application parts and electronics or even complete sensing solutions.
|
|
The sensor is suited for torsion measurements and the measurement of reaction moments for orthopaedic measuring devices. It is applicable for measurements of friction forces.
The strain gauge full bridge measure the torsion movement appearing in the tube of the lattice structure.
|
|
FLINTEC load cells are designed to meet the most stringent
accuracy requirements. Certifications have been obtained
from Weights & Measures Authorities, worldwide. Single Point load cells are available in the capacities 6kg to 2000kg and include Accuracy Classifications GP,
C1, C3, C3 MI 7.5, C4 and C4 MI 7.5 according to OIML R 60;
Beside the aluminium Single Point Load cell Flintec offers total stainless steel construction and complete
hermetic sealing, making them suitable for use in the toughest industrial environments.
ATEX versions available.
|
|
FLX
Bending Beam Load Cell
> 3000/6000d OIML
> 50/100/200 kg
FFX
Bending Beam Load Cell
> 3000/6000d OIML
> 300/600/1500/3500/5000 kg
|
|
TesT electronic force measurement systems comprise the load cell (sensor), connector cable, plugs and electronics.
Load cells are available to detect compression and tensile forces of between 1 N and 40 MN, in various accuracy classes and operating ranges.
|
|
| ... products without technical information |
| |
|
|
