|
|
|
AGI has a full line of linear actuators, base slides, Magnetically coupled slides, thrusters and pneumatic actuators that provide smooth linear motion due to the precision ball bearings riding on hardened ground shafts. The aluminum body and end blocks contain tapped holes and dowel pin holes for precision mounting or fixturing. The AGSL slide series have a magnetically coupled rodless air cylinder that drives the saddle. AGS series have a built in air cylinder that reduces the overall length or footprint. AGT series thruster slide series are powered by an external air cylinder and have an exclusive dual end plates system to keep the shafts from vibrating. Bore sizes are .75 inch, 1.00 inch, 1.25 inch, and 1.50 inch with strokes from 4 inch to 132 inches long. Polycarbonate composite bearings are also available.
|
|
Linear Motor Actuator
LMS Series (LMS 20, LMS 30, LMS 50)
Specifications Range Across LMS Series
Continuous Force: 21.5 - 252 N
Peak Force: 86 - 920 N
Maximum Velocity: 5 m/s
Maximum Acceleration: 100 m/s²
Maximum Carriage Weight: 0.96 - 2.5 kg
Direct Drive Design.
High Speed.
High Strength Aluminium Profile.
Resolution of 10µm, 5µm, 2µm, 1µm, 0.5µm, 0.1nm, 50nm, 20nm, 5nm, 2.5nm, 1.22nm.
Zero Backlash
Least Maintenance Required
--------------------------------------------
LMSDG Series (LMS 30DG, LMS 50DG, LMS 65DG)
Specifications Range Across LMS DG Series
Continuous Force: 36 - 616 N
Peak Force: 133 - 3040 N
Maximum Velocity: 5 m/s
Maximum Acceleration: 100 m/s²
Maximum Carriage Weight: 1.5 - 11 kg
Maximum Carriage Length: 120 - 540 mm
Direct Drive Design.
High Speed.
High Strength Aluminium Profile.
Resolution of 10µm, 5µm, 2µm, 1µm, 0.5µm, 0.1nm, 50nm, 20nm, 5nm, 2.5nm, 1.22nm.
Zero Backlash
Least Maintenance Required
High Moment Rating
High Load Rating
|
|
Xenus
100-240 VAC Digital CANopen Amplifier for Brushless/Brush Motors
Built-in position sensor (12 µ repeatability)
Moving-rod actuator
Moving-forcer motor
Matched Xenus and Accelnet controllers
High rigidity version with outrigger bearings
No lubricant, internal actuator bearing
Drop-in cylinder replacement
Quiet operation
Food-safe
Holding brake option
|
|
SBC Linear actuator
The wide range of SBC actuator models allows you to select a specific unit that best suits your needs. Very applicable to Factory Automation and convey system.
High rigidity
High accuracy and high repeatability
The wide range of models (OPEN Type, Close Type)
Drive Unit Compatibility
MS/MB Series - Mini Linear Actuator
The MA series is the SBC miniaturized linear drive unit of the same width and height. It's small and compact size package suits many application requirements. The ball screw drive units can utilize varying leads offering stroke speed versatility. The belt drive model, using parabolic RPP-belts, offer high-load, low noise and precision movement.
|
|
Frame Size 2-4 inches, 51-102 mm
Stroke Length 2 – 18 inches, 51-455 mm
Maximum Continuous Force Rating 5300 lbf, 24 kN
Maximum Continuous Torque Rating 107 lbf-in, 12 Nm
Maximum Velocity 25 in/sec, 635 mm/sec
Maximum Motor speed 5000 rpm
|
|
Nook Modular Linear Actuators are flexible positioning systems made of self-supporting and wear resistent aluminum profiles. Modular linear actuators can be used as a single axis solution or assembled for a multitude of gantry XY and XYZ positioning duties including inspection, pick-and-place, assembly or dispensing applications.
NOOK Modular Linear Acuators are fully assembled with either roller bearing, profile rail or V-groove guidance and are driven by a belt, ball screw, acme screw or linear motor. Matched non-driven models are available for system guidance requirements. Over 35 models, each with several available sizes, meet the requirements of guidance, load and speed for precision and commerical linear motion applications.
|
|
High Accuracy Single Axis Actuator BG Type
NB's BG Type is a compact single axis actuator which integrates a Slide Guide and Precision Ball Screw. BG Type offers compact dimensions, which outperforms conventional positioning tables. This is made possible by a unique "U" shaped Guide Rail and Slide Block which provides multiple functions of a Guide Block and a Ball Screw Nut combined into a single unit. The "U" shaped Guide Rail design offers a high rigid structure resistant to bending. This structural feature allows for integrated frameworks of machinery or equipment. Additionally, the Slide Block contains 4 ball circuits which delivers high load capacity, high accuracy and high rigidity.
|
|
The NB BG type is a compact single axis actuator, which integrates a slide guide and precision ball screw. BG type offers a unique “ U “ shaped guide rail and slide block which provides multiple functions of a guide block and a ball screw nut combined into a single unit.
The slide block contains 4 ball circuits which deliver high load capacity, high rigidity and high accuracy.
|
|
RACO's linear actuators with tooth belt drive or spindle drive for single- and multiple-axis movements, put together for specific requirements with the motor drives required such as RACO's intelligent positioning motor, servomotors or step motors and the amplifier and control units as a system application. Or is may also be integrated into existing systems as individual building blocks.
Technical highlights:
stroke to 9 m
linear speed up to 17 m/s
linear thrust to 20,000 N
positioning accuracy up to 0.08 mm
no energy consumption at stop
accessories and electronic modules of RACO's electric actuators can be integrated
|
|
Basically, the IF is a "belt-driven version of the IS Actuator". By combining the high moment loads of the IS with the speed of the FS, the IF Series has proven itself in providing torsional rigidity, reliability, and high speeds. Here is what the IF Series provides:
* AC Servo Motor
* Maximum stroke length: 2500 mm
* Maximum speed: 1750 mm/sec
* High rigidity base structure
* Double slider option for large moments and overhang
* Highly durable urethane composite timing belt
* High base resistance to torsional deformation
|
|
Simple solution and economic for small budget:
Cartesian robot 2 axes of modular concept
Race centers X up to 2500 mm
Race centers Y up to 1000 mm
Charge with Maximum with 5 kg
Speed 120 m/s
Precision + 0,1 mm
Engine step by step or brushless with programmable integrated electronics
Entries end of the road and integrated catch of origin
Digital entries and exit TOR available
Communications available: Ethernet/USB/Profibus/RS232/RS485
Position and shifting of speed to the flight
Storage of the programs
Manual or automatic movements
|
|
These units are primarily for lifting or lowering Masses in both Vertical & Horizontal planes. The weight to be lifted is from 250 kg (0.25 Tons) to 150000 kgs. (50 Tons through various Frames of 0.25 T / 0.5T / 2 T / 2.5T / 5T / 10T /20T / 35T / 50T / 100T / 150T (T indicates Tonnage). These units give positive mechanical action, fail proof & Precise Positioning. The Height to be lifted (or) lowered can be upto 3000 MM.
There are two standard speeds available viz., Normal lift & Slow lift. Housing / Shell is made of Nodular (SG Iron) Casting from 2 Ton to 150 Tons. For 0.5 Ton & 1 Ton Models we use Aluminum shells & covers
There are two types viz
Lifting screw rod with the stationary head
Rotating Screw rod and moving NUT. Both types have two further design possibilities of Design A (upward & Design (B) Downward. All the Jacks can be used on sideways (or) angular ways also
|
|
Moter Free Type
Free Selection Motors of Standard Actuator
Features
Based on KUMI and KUMIKO series, fitted to various motors for various requirements.
Meet to various control making it easy to use.
Optional sensors for all sort of mortors. Free assemblies.
Compact size with light weight.
|
|
Demands for higher speed, enhanced quality and less cost are increasing
more than ever. How to meet these demands quickly is the task
expected of manufacturers now and in the future.
YAMAHA PHASER series is a completely new line up of
high performance single axis robots in which the cost
factor and performance are combined in a desirable
way."YAMAHA PHASER series"is the key word
that in creating the manufacture scene of the
next generation with new value concepts.
|
|
APPLICATIONS
Fifteen year old fruit d’ experiment units SGLT are
already used in many fields:
Manipulator impression with jet d’ ink
Palletizer Drilling of printed circuits
Machines d’ gluing Engraving on plastic
Teaching placement CMS Machines
Special machines Machining
Displacement of heads d’ etc...
CHARACTERISTICS
. Quality ratio/price
. Lifespan
. Good precision of displacement
. Reduced weight: construction in alumini
|
|
ZIMM – Screw Jack Building Block System
We lift, lower, push and pull loads from 5 to 1000 kN.
* Efficient construction due to our Screw Jack Building Block System - all components compatible
* All components from one supplier saves purchase costs.
* Delivery of pre-mounted units and assembly groups, motors included
* Short delivery times
* Capable of bearing tension and compression loads
* Attractive design
* Stainless spindles and components on request
* Custom components for specialist applications on request.
|
|
|
STN 16 with 80mm, 4 versions. RTC-BV: guidance interns by oval piston, Applicability: transport, open-carries, cut, devices of thorough RTC-CG: guidance on compact rail and of high precision, Applicability: average charges in an exiguous space RTC-EG: guidance on rail of high precision and an effective cost, Applicability: RTC-HD with E-Line guidance, to involve not guided objects RTC-HD: guidance on rail of high precision, for the raised loads, Applicability: basic axis for the applications of handling, very high capacity load
|
|
|
GSU Dia. 16 and 25mm. Element of the range Easy-2-Combines. Race until 1000mm, flexibility of adjustment of the race. Small overall dimensions (flat design). Allows a high speed of drive.
|
|
Ultran Rodless Cylinders
The Bimba Ultran rodless cylinder provides one of the highest coupling strengths available. This means it can carry higher loads without causing the piston to uncouple from the carriage.
Bimba also offers two magnetic coupling strength options (Gold and Silver) to suit a wide variety of applications. The Silver option uses two sets of magnets instead of three.
Bore sizes are 5/16", 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", and 2".
Bimba offers a model with built-in guides (Ultran Slide) and an unguided unit (Ultran).
Save space and streamline your design with the Bimba Ultran rodless cylinder! Application possibilities include transferring, feeding, door opening, cutting, silk screening and overall length savings.
|
|
Guiding cylinder
with two slide guides
with short slide guide
with safety unit
with slide guide underneath
Technical Information
· ZSS and ZKS have been designed for higher loads.
· By mounting a linear guide way on the bottom side of the cylinder, very high loads and moments can be carried forward
· Maximum stroke 3000 mm, longer on
· ZSS with two guiding carriages and a fitting length just like the ZS standard cylinder
· ZKS with a guiding carriage
|
|
GSU Dia. 16 and 25mm. Element of the range Easy-2-Combines.
Race until 1000mm, flexibility of adjustment of the race.
Small overall dimensions (flat design). Allows a high speed of drive.
|
|
REXMOVER Dia. 16 with 80mm, race of 100 with 9.900mm possible according to the version.
System with compactness for long races at high speed (5M/s).
4 types: guidance internal, polyamide, external or reinforced. Center robust linear drive.
|
|
|
Mechanically jointed rodless cylinder series MY3 provides high functionality with reduced height and length. The uniquely designed piston shape enables reduction of the height and length as well as practical arrangement of the common piping passages, cushion mechanism and positioning mechanism. This has achieved drastic miniaturization and weight reduction.
|
|
A space saving and guided cylinder with no equal. With a sealing system
unlike any other and endless possibilities including true synchronization
of two or more cylinders the ZR is worth a look.
The answer for dirty and dusty environments.
Available with slide or roller guide
Extremely low leakage
Smooth linear movement
High durability and operational reliability
Deliverable with a brake and encoder
Integrated valves if required
|
|
| ... products without technical information |
| |
|
|
