|
|
Y type globe valve
ND (nominal diameter): 15-400
other diameters or pressures under request
NP (nominal pressure): 16-420
MAIN TECHNICALS SPECIFICATIONS
Execution: A105, AISI 316, AISI 304
Waterproofness PTFE or the other joint in the demand
Can have risen with any types of actuators
Connection of actuators following one ISO 5211
Fixation to reins or to weld
Technology: Molded or Forged
|
|
This type of valve is actuated by pressure acting on a piston or diaphragm. The fluid is usually neutral e.g. air, water, hydraulic oil. The pressure range varies and is specified accordingly in a data table.
"Normally Closed" (N/C) valves of this type remain closed under spring pressure, when de-activated.
"Normally Open" (N/O) valves of this type remain open under spring pressure, when de-activated.
When pressure is connected to port "Z" the valves open or close according to type.
A separate 3/2 pilot valve is used to supply pressure to port "Z", it is mounted either directly on the actuator or remotely.
In some cases a 4/2 or 5/2 pilot valve will be required. The main valve position can be N/C or N/O. The basic position is determined by connecting the pilot valve output lines accordingly. (The direction of flow is usually indicated by an arrow or shown schematically on the body).
|
|
ASCO/JOUCOMATIC has developed a wide range of valves for all fluids, whether neutral or aggressive, made out of brass, bronze, cast iron or 316L stainless steel.
Reliability is ensured by:
* A monobloc rod, with stainless steel from the reed to the piston
* Guidance by 2 extra-large PTFE bearings.
Pilot solutions: solenoid valves on valves or mounted on subbases and valve islands.
|
|
PNEUMATIC VALVE 2/2 NC ANGLE HEAD
TECHNICAL SPECIFICATIONS
Media: air - water - steam - light oil
Pressure range : 0 to 25 bar max
Media temperature : -30° to +180° C max
Ambient temperature : -10° to +70° C max
Media viscosity : 600 centistokes max
Pilot media : filtered air or water
Pilot pressure : 4 to 10 bar max
|
|
|
The new ODE 21IA series is characterized by the angle seat body in stainless steel AISI 316, as all the components in contact with fluids. The angle seat specific body design allows to maintain the fluid flow extremely stable in order to guarantee a high flow values. The auto positioning floating shutter system and the Teflon ring guarantee good seal and reduced leakage over time. Moreover the particular configuration makes the valves resistant as well against fluids with abrasive and chemical contaminants. The standard configuration with flow in direction under shutter allows the execution anti water hammer. It’s available on demand even the version with flow above the shutter for application with gasses and steam.
|
|
General description
M&M piston actuated valves are manufactured with high performing components as a standard.
PTFE and FKM seals together with internals in AISI 316 offer outstanding compatibility and cover a wide variety of industrial applications.
Added features as position indicator, built-in exhaust filter, wide choice of connections and optional versions, long life cycles even in severe conditions represent our competitive advantage.
|
|
ASCO/JOUCOMATIC has developed a wide range of valves for all fluids, whether neutral or aggressive, made out of brass, bronze, cast iron or 316L stainless steel.
Reliability is ensured by:
* A monobloc rod, with stainless steel from the reed to the piston
* Guidance by 2 extra-large PTFE bearings.
Pilot solutions: solenoid valves on valves or mounted on subbases and valve islands.
|
|
|
|
|
|
TORK T-PV Series ,pneumatic piston valve
application: water,air,steam,gas,natural gas,chimicals,petroleum products,food,sterilazation,water treatment,dyeing,cleaning plant,aggressive liquids,vacuum application,oil,petrol,alcohole,hydroulic liquids,salt solutions,acids,organic solvent
All body is AISI316 Stainless Steel,high flow rate,high quality,compact,suitable vacuum application,normally open and normally closed position.
advantage of TORK pneumatic piston valves:less pressure drop than globe valve,
short open-close time
high flow rate
body and actuator AISI 316
screwed,flanged and welding connection
on-off and proportional control
TORK T-PV Series ,pneumatic piston valve series range
T-PV.S700 Serie; Screwed connection, 1/2"......2" G( BSP ), on request NPT connection..
T-PV.W700 Serie; welding connection, size :from 1/2"......up to 2" .
T-PV.F700 Serie; Flange connection,size:from NW15.....up to .NW50 .
T-G.3W Serie: Solenoid valve,1/4"-3/2 way.it is used on-off control pneumatic piston valves
T-SW Serie: Proximity switch limit switch box ,gives signal when valve open-closed.
|
|
For the dosing of liquid chemicals, Alltech Dosieranlagen GmbH has developed the piston diaphragm metering pumps of the FKM series.
These metering pumps meet the highest requirements in operational reliability and accuracy.
Alltech piston diaphragm metering pumps are built in a modular concept. This guarantees high flexibility in combining the pump elements for various areas of applications.
By using different materials and designs for the liquid end, Alltech metering pumps may be used for the dosing of almost all kinds of chemicals.
To find an optimal solution for your dosing tasks, we offer various dosing capacities and pressure ranges.
The integrated pressure relief valve guarantees maximum security.
A wide range of accessories (stroke actuators, pulsation dampers e.g.) completes the range of our production.
|
|
The MultiFertic® dosing pump is a heavy duty, high precision electric or diaphrgam pump for dosing chemicals products and additives. It is made up of one driving module and 1 to 4 injection modules for 25 to 500 L/H (7.5 to 150 GPH).
In order to dose different products (INDEPENDENT INJECTION) or increase the inyection flow, several injection modules can be connected in the same injector. If we do so, we can obtain a higher flow regularity. In the case of 4 modules the injection flow is practically constant.
|
|
|
For corrosive and abrasive media, which have to be dosed against higher pressures than 16 bar piston pumps can be fitted with a piston-diaphragm system. The KMS system combines the advantages of leakage-free diaphragm dosing pumps and precise piston dosing pumps and thus ensures reliable dosing.
|
|
| ... products without technical information |
| |
|
The range of Airless & Air Assisted system ARO has been designed to provide sprayers with a very robust industrial assembly, able to apply a wide range of industrial coatings whilst providing the very best quality of sprayed finish. The packages are available in a variety of mounting options including; Tripod, Cart, Wall and 25 Litre Pail. The Pumps are complete with a 5 Year Warranty
|
|
|
The BINKS H.P. Range of Airless & Air Assisted Airless Spray outfits have been designed to provide sprayers with a very competitively priced, robust industrial assembly, able to apply a wide range of industrial coatings whilst providing the very best quality of sprayed finish.
|
|
High pressure and high fluid flow per cycle increases your production and reduces rod and cylinder wear
Severe Duty rod and cylinder handles the most abrasive coatings
Simple design makes fluid pump repairs easy
Designed for applications requiring large tip sizes, long hoses and high flow rates
Exclusive air valve design minimizes ice-related downtime
|
|
| ... products without technical information |
| |
Piston Accumulators Parker's hydraulic accumulators for industrial and mobile applications provide a means of regulating the performance of a hydraulic system. They are suitable for storing energy under pressure, absorbing hydraulic shocks and damping pump pulsation and flow fluctuations. Their simple, compact, design ensures dependable performance, maximum efficiency and long service life.
Parker's piston accumulators are manufactured in compliance with the European Pressure Equipment Directive 97/23/EC (PED) and carry the CE mark where applicable. Other approvals are available on request.
Parker offers the A Series range of piston accumulators for mobile applications such as damping and ride control. For industrial applications, A Series and AP Series accumulators are offered to suit different application and performance criteria.
|
|
Rated to 3000 psi, piston type, designed for long life and easy maintenance.
|
|
|
Fluids are practically incompressible and cannot therefore store pressure energy. The compressibility of a gas (nitrogen) is utilized in hydropneumatic accumulators for storing fluids. EATON piston accumulators are designed on this principle, using nitrogen as the compressible medium. A piston accumulator consists of a fluid section and a gas section with the piston acting as a gas proof screen. The gas section is precharged with dry nitrogen gas. The fluid section is connected to the hydraulic circuit so that the piston accumulator draws in fluid when the pressure increases thus compressing the gas. When the pressure drops, the compressed gas expands and forces the stored fluid into the circuit.
|
|
The hydro pneumatic piston accumulator, or piston accumulator, is a sort of tank in a hydraulic circuit,
capable of storing a large quantity of energy with a low volume.
A piston accumulator is divided in two chambers: one for the fluid under pressure, the other one for the
nitrogen (or other type of gas). The two chambers are separated from one another by a piston.
In case of peak of pressure in the hydraulic circuit, the fluid pressure is higher than the initial pressure
(called inflation pressure). When the fluid arrives in the piston accumulator, the nitrogen will compress
and will therefore retain the corresponding fluid.
|
|
The present K3V is designed specifically for the earth moving and construction industries where in excess of 700,000 units have been supplied.
Features such as high efficiency , high power density, large self priming capability, long life, low noise and a wide range of control options has enabled the K3V to be a clear market leader.
Adopting a process of continual product development has resulted in todays K3V series of axial piston pumps.
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
|
|
Axial piston units are available in the form of pumps and motors in bent axis design or swashplate design for medium- and high-pressure ranges. They are the main components in the hydrostatic transmission. Compact size and high power density, economy and reliability are characteristic advantages which speak for the use of hydrostatic transmissions, together with the fact that they meet the demand for high speed and high torque, as well as optimum efficiency.
|
|
|
The Verder Wrightflow circumferential pumps series are robust pumps for hygienic applications, solids handling is no problem. Max. flow 103 m3/h, max pressure 34 bar.
|
|
Lubricating pumps for marine gearboxes. Gearbox driven direct coupled pumps. Auxiliary lubricating pumps with electric motor drive
Metering pumps for polyols with abrasive fillers with separate bypass valves
Gear pump for hot oil circulation - special design
Metering pump for the polyurethane industry with integral pressure limiting valve, seal chamber and geared servomotor as a complete unit
|
|
| ... products without technical information |
| |
This drum drainer system for fully opening drum is used to transfer high viscosity products, even those with no flow capacity such as grease, lubricants, glues, silicones, inks or similar products.
This is a hybrid system, pneumatic for the descent of the follower plate, guaranteeing constant feeding of the pump, and electric for the positive displacement CM tec-technology pump to facilitate the transferring of large quantities.
The volumetric pumps that equip this system have a capacity of up to 90 L/min and 10 bars of pressure.
Product Features
Drum drainer pump :
§ CMtec technology with monoblok blades and a curved stator.
§ Hybrid system : pneumatic frame with a follower plate and a volumetric pump.
§ Optional : metering system and a trigger gun.
-Designed for an intensiv use
-Excellent quality/price relation
PERFECT FOR THE PUMPING OF VERY HIGH VISCOSITY PRODUCTS
Such as :
- grease
- glues
- lubricants
-products containing additives
-silicones
-inks
|
|
... see all the products in the category
Drum pumps
|
|
|
see the results for the following category : 
