|
|
VCC's LCS Series Litepipe® provides display panel moisture seal and 180° viewing angle. This lens and Litepipe® unit was developed to provide moisture sealing and dust control for display panels when the LED is attached to a circuit board.
Currently, the moisture sealing of a Litepipe® to a display panel requires the use of RTV-type adhesive. When applying glue for sealing, special precautions must be taken to avoid creating air gaps that would allow sealed joints to leak. Glues are not only difficult to apply but their adhesion to a lightpipe surface will change the flow of the light pattern. This also causes light leakage resulting in reduction of light emitted by the litepipe. In addition, the output surface of a lightpipe alone whether flat, concave, or convex projects little or no sidelight. This gluing method results in serious assembly problems and less than satisfactory panel displays. |
|
| EXFO High Power Fiber Light Guides, supply an equal distribution of light energy to multiple cure sites from a single light source. This new Light Guide technology provides 25% to 50% more throughput than standard fiber guides to give you more energy from your lamp. In addition, these Light Guides offer 25% more output than bifurcated liquid Light Guides and do not require balancing of the legs. |
|
Flexible Light Pipes
Flexible Light Pipe Assembly
Flexible Light Pipe IP67 Watertight Lens Assembly
Flexible Light Pipe Infrared Lens Assembly
Flexible Light Pipe Lens
Flexible Light Pipe Through-Hole Assembly
Flexible Light Pipe SMD LED Assembly
Rigid Light Pipes
90 ° Multi-level SMD Style
Panel Mount Light Pipe Rear-Mount
Panel Mount Light Pipe Front Mount
Panel Mount Light Pipe Dual Lens Style
90 ° Variable Centerline SMD
Vertical Board Mount Round SMD
Vertical Board Mount Rectangular SMD
|
|
| ... products without technical information |
| |
Since the creation and patenting of the original DualVee® wheel in 1967, it continues to provide easy to use, easy to install guide wheel components and assemblies. DualVee is ideal for a wide array of applications, from the clean room to the sawmill. These rugged yet economical guide wheels are quiet, ideal in long length applications, and tolerant of harsh environments.
DualVee's recirculating elements are self-contained and isolated from the environment; rolling contact between the wheel and track sweeps debris aside, making it ideal for use in contaminated environments.
DualVee offers three different wheel options; original guide wheels, studded guide wheels, and new integral one-piece guide wheels for lower cost and ease of installation. A wide variety of bushings and journals are available.
DualVee single edge or double edge track with patented mounting shoulder is available in carbon steel or stainless steel, induction hardened or "as formed". Hardened track comes in single lengths up to 20 feet, unhardened in lengths up to 22 feet. Track is easily butt-jointed for longer length applications.
A number of accessory items are also available including wheel covers, lubricators, track plate assemblies and wheel plate assemblies.
|
|
A highly effective system for lower cost and accuracy builds up from a single edge track and matching wheels. DualVee components are available in a range of sizes to suit most applications with high temperature and vacuum/clean-room options available to complement existing stainless steel components.
- Track lengths up to 6m with unlimited lengths achievable by butting
- Available drilled or un-drilled to minimise additional engineering
- Ex-stock availability |
|
Guide roller with threaded rod
- Profile in arc of circle for fonctionnemenî on tree
- Lubricated with life and tight
- Composed of a roll of the dice with two oblique lines
- Fixing of the roller by its threaded rod
- Exist in standard version (ref.: FRW) or with eccentric (ref.: FRWE)
- Also Exist in lNOX (ref.: FRW... - VA.FRWE... - GOES)
Another products available: |
|
- Can be added to any Hilman Roller and designed to interface with almost any type of track.
- Ideal where load alignment is critical, close tolerance must be maintained, the load movement is repetitive, or where uplift prevention is desirable.
- Can be designed to be detachable from the Roller or adjustable to fit multiple tracks. Guidance systems with tapered rolls are also available.
Components :
- Type R - for guidance on I-Beam, Tube, Flat Bar, or Rail.
- Type C - for guidance in Channel or Trench.
- Type U - guides against the underneath side of I-Beam or Rail to prevent Roller uplift.
- Type TR - provides guidance when used with a radiused track.
- Hilman will also design and manufacture Rollers and systems to meet customer specifications and operational requirements.
Capacity :
- Available in a broad range to suit Roller capacity and application requirements. |
|
YTGW Guide Wheels are the main components of the Linear Motion system, they can be widely used in the industrial robot, cutting machine, motion track, production flow and so on.
The surface of outer ring is the "W" profile formed by the two "V" with an angle of 90 degrees. The internal or external side face can be matched separately with the concave or protrudable track that both have a "V' profile with the angle of 90 degrees, and also the internal side face can be matched well with the cylindrical track.
Wheels feature the internal design of double row angular contact ball bearing and a thick-walled outer ring, so the wheels can accommodate higher loads.
Wheels are made of the high-quality bearing steel, processed by heat treatment and precision grind, and are filled with a long service life, high-grade and multi-purposes grease. Wheels mantle the metal shield or rubber seal (suffix X) to prevent the dust. YITONG also can provide the wheels with the concentric or eccentric bushings, as well as the wheels made from the corrosion resistance stainless steel.
|
|
| ... products without technical information |
| |
Rockline® RBP1 Belt Positioner
The Rockline® RBP1 Belt Positioner™ is the simple, reliable solution for problem belts that continuously mistrack to one side of the conveyor. The Belt Positioner works on the return side belt using simple angled rollers mounted in a fixed position to quickly and continuously funnel the belt into the correct path.
The RBP1 Belt Positioner’s innovative design does not rely on a pivoting mechanism to move and steer a wandering belt like conventional tracking units. The RBP1’s two idler rollers are adjusted to the belt and create a funneling action that continuously "positions" the belt into the correct path. Many times in as few as 5 revolutions of the belt the results can be seen. Plus, the idler rollers on the RBP1 make smooth contact with the return side belt’s bottom cover and not on the belt’s edges which can cause excessive wear and damage to the belt.
Installed before the tail pulley, the Belt Positioner keeps the belt centered at its critical loading point. The RBP1 can also be used at the head pulley, before or after the take-up pulley or anywhere on the return beltline where there is a belt tracking problem. It can also be used on reversing belts.
The RBP1 Belt Positioner comes assembled and ready to install. Simply preset the unit for the conveyor structure width, position the unit on the belt and bolt or weld in place. Adjust the rollers to the belt and watch the results. |
|
Rockline® RMC1 Skirt Clamps provide the cost-effective solution to material spillage problems in your conveyor loading zones. A good material containment system at the loading point reduces conveyor problems and saves cleanup costs. It stops material loss, eliminates safety hazards and reduces wear and premature failure of conveyor components. RMC1 Skirt Clamps are designed for easy installation, quick maintenance and years of service.
RMC1 Skirt Clamps come in a standard 4" (1200mm) length. An optional "Limited Space" (LS) model is available for tight chute configurations or for portable equipment. Also offered is a "Pick-A-Length" (PAL PAK) option for longer length or special length requirements. The RMC1 handles a variety of skirt rubber sizes. It can also be used with a range of skirt rubber thicknesses from 5/16" (8mm) to 3/4" (19mm).
The RMC1 features a no-hassle installation with few parts. First the clamp pins are positioned on the conveyor's skirt board and welded into place. Then the clamp plates are hung on the pins and the clamp bar and the skirt rubber are inserted. And finally, the clamp bar is tack welded to the plates.
All installation and maintenance work can be done safely from the sides of the conveyor. Just tap loose the locking wedges on the clamp pins, reposition the skirt rubber and relock the pins. The rest of the parts interlock so when the pins are unlocked, they remain in place supporting the skirt rubber while maintenance is completed.
|
|
The automatic adjustable product guiding system provides a flexible way to add fast width adjustment for conveyors in a production line.
The system offers quick and easy automatic resetting of product guiding systems in production flows. The effect is increased line efficiency and safe product distribution throughout the line.
The system has a modular design and consists of guide units for the guiding, controls for the control of the guide units and junction boxes for power supply. The system can be linked to the line control system and one control box can control up to 220 guide units.
|
|
| Thanks to a very large product range, an unceasing commitment to innovation, and extremely high quality levels, SEDIS is able to satisfy the requirements of the most demanding users |
|
| ... products without technical information |
| |
| ERNI offers the industry's widest array of cable housings, strain reliefs and guide elements. These complementary items to the DIN 41612 / IEC 60603-2 connector family are available for all of the popular types including B, C, D, F, H, Q and R and 1/2 sizes. The cable housings offer rear and two sided exit options, with strain relief for wire, jacketed cable or flat cables. The guide elements are available with keying and screw lock features for applications including: edgecards, backplanesm front panel, rear panel and other 19" Eurocard subrack mounting applications |
|
Richco offers a range of vertical, horizontal mount and tensioning rack card guides. Vertical design keeps boards in place, yet allows easy slide in and slide out. Horizontal guides are available with a funnel entry for easier board insertion, while others come with tension grips, applying spring pressure to hold the board securely in place.
In chassis and rack system applications, PCB access needs to be quick, accurate, safe and easily accessible to avoid damage to the components on board, which need to be utilised without compromising on overall performance.
The wide range of Richco card guides and pullers provide a solution to PCB safety access for when routine installation, maintenance and repair needs to take place. Custom parts are available. Please contact you local Richco office to discuss your requirements.
|
|
OILES LF Guide
Guide unit bearing
STANDARD PRODUCT
Guide unit interchangeable in dimensions with linear bushings
OILES LF Guide is a guide unit in which OILES Drymet LF and dust seal are structured in aluminum housing.
Features:
- Usable without lubricating because of OILES bearings.
- Usable in the vapor because of rustproofed aluminum housing.
- Excellent wear resistance and low friction coefficient.
- Easy to fix and interchangeable with ball type bearings.
- Realized low price owing to the simple structure.
|
|
Misumi is the NO 1 supplier of over 500,000 standard and customised components for Mechanical Factory Automation/Special Purpose Machinery, Press Dies and Plastic Mould. We delivery components europewide in averagely 6 – 8 days GUARANTEED DELIVERY from the day of purchase, stock items available from 2 days delivery.
Misumi components are different in that they can be configured to your need using our unique part coding system. Dimensions, materials and special machined requests can all be selected within the misumi system enabling engineers and designers to achieve a configured parts as standard with no extra machine costs. Standard items are also available via the catalogues.
All components can be designed using the Misumi CAD portal . Compatible with industry wide packages a designer can configure our parts at the touch of a button in up to 0.01mm, and download in seconds saving valuable design time, registration required.
To receive our extensive catalogue and save valuable time and money, visit our website or request yours today by clicking the request banner.
MISUMI – Precisely what you need. |
|
| Pacific Bearing offers a variety of shafting, rails and accessories such as Feather Shaft™, Feather Rail™, RC60 Steel, 440 Stainless Shafting, and custom options. |
|
LM76 offers extremely competitive pricing on all types of precision shafting: round, hollow, predrilled, continuous support extrusions, predrilled & assembled shafting. We specialize in standard linear shafting:RC60/Class L Linear Shafting, 300 series s/s Linear Shafting.
For most applications, RC60/Class L is the linear shafting of choice with all LM76 linear bearing styles: Minuteman, Ceramic Coated and FDA/USDA acceptable. |
|
Our manufacture are composed of:
Standard trees of precision CK55 ISO h6 62 /- 2 HRc
Chrome trees of precision CK55 ISO h7 62 /- 2HRc
Hollow shafts of precision CK60 ISO h6 62 /- 2 HRc
Trees of precision stainless 18% X90CrMoV18 ISO h6 55 /- 2 HRc
Trees of precision stainless 13% X46Cr13 ISO h6 53 /- 2 HRc
Standard trees of precision Inch CK55 ISO h6 62 /- 2 HRc
Chrome bars CK45 ISO f7
Chrome bars stainless AISI 304 ISO f7
On request we can manufacture all types of diameters, nuances and tolerances on minimum quantities
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
|
|
see the results for the following category