|
|
|
|
|
|
The Aeroflex 7200 Configurable Automated Test Set (CATS) platform provides the most state-of-the-art synthetic instrument platform available today, while providing support for future next generation devices.
Flexible Configuration Options
* Micro ATE™ configuration with built-in signal switching for total test automation
* General purpose instrument configurations with high performance front panel oscilloscope and DMM connections
* Multiple signal generation and measurement channels available
Broad Frequency Coverage
* DC to 2.6 GHz standard
* Options to 40 GHz
Ultra-wide Instantaneous Bandwidths
* 90 MHz standard
* Options to 500+ MHz
Software Defined Radio Ready
* SCA compatible architecture
* Powerful/ expandable real-time baseband
* processing with deep memory
Robust Packaging
* MIL-PRF-28800F Class 3
* Rack mount option
Advanced Capabilities
* State-of-the-art and highly intuitive touch screen based user interface
* Drag-n-drop test executive with breakthrough automatic test execution optimization for lower test times
Standard Instrumentation Functions Include
* RF Signal Generator and Tracking Generator
* RF Measurement Receiver
* Power Meter
* Spectrum Analyzer
* Digital Oscilloscope
* Audio Generator and Analyzer
* Digital Multimeter
* Distortion Meter
* SINAD Meter
* Frequency Counter
* Bit Error Rate (BER) Meter
* Frequency Reference
Optional Functionality
* Analog and digital I/O
* Databus emulation and test
* GPS location, emulation and test
* Power supplies and loads
* S-parameter test set
* Removable Storage, and more...
|
|
|
The Aeroflex 7100 LTE Digital Radio Test Set provides all the tools required during the design, development and test stages of UE chip sets and terminals meeting the new Rel-8 standards. All the key measurements are provided for characterizing the performance of LTE mobile devices, both at the radio interface and throughout the protocol stack, including the PCDP and IMS layers. End-to-end performance can be accurately assessed, along with correct idle mode and connected mode behavior with the 7100's Network Simulation mode.
|
|
The 3500A improves upon the success of the Aeroflex 3500, the industry's first 1GHz hand-held test set. Now at less than 8 lbs., and packaged in a NEW cast magnesium alloy case, the Aeroflex 3500A is truly a rugged and portable radio test set. With NEW integrated audio connectors and a microphone connector, the 3500A offers even easier operation than the 3500.
A Radio Test Set that can be used anywhere
Featuring full radio test set features, with up to 7 hours of battery life, the Aeroflex 3500A is ready to be used anywhere. The 3500A is perfect for testing AM and FM radio transceivers, whether on a bench, installed in a vehicle, or in some remote location. It also has the power to test the cables and antennas, making it the only hand-held radio test set that can test all the components of an installed radio system.
|
|
|
|
|
|
The 3920 is the latest in next generation portable test for advanced professional analog and digital radio communications. Building upon a long-standing reputation for excellence in professional radio communication test, the 3920 from Aeroflex sets a new benchmark for quality, ease of use, performance and value.
Platform:
Within the 3920 Series is a Pentium based processor coupled with a stable Linux platform provides a solid foundation for a powerful systems based test solution capable of addressing many different technologies. Three powerful digital signal processors can deliver unparalleled performance to address many different test requirements with ease. An internal 40 GB hard drive provides virtually unlimited storage for user setups, screen shots and test data. Files can be easily transferred to a USB thumb drive for external storage or processing. Setup files can be easily transferred from one instrument to another.
The platform also supports the ability to add software options to expand the measurement and signaling capabilities for communications systems that utilize advanced digital modulation and protocols.
|
|
|
|
|
|
The IFR 6000 is a compact, lightweight and weatherproof unit designed for testing MODE A/C/S transponder, DME, TCAS, ADS-B and TIS avionics systems.
IFR 6000 features include:
* Mode S level 1-4, (level automatically determined), FAR Part 43 appendix F, (including proposed Eurocontrol extension), Eurocontrol Elementary and Enhanced Surveillance
* ADS-B TX/RX
* TIS
* ICAO Annex 10 amendment 77
* Quickly and easily provides accurate measurement of transponder transmitting frequency, power and receiver sensitivity. Predetermined configurations for testing any class of transponder.
* Tests any DME 1 MHz spaced X or Y channel. Measurements include: interrogator transmitter frequency/peak power, Pulse Repetition Frequency (PRF), P1/P2 width and pulse spacing. Provides accurate range and velocity simulation, station ident, squitter control.
* Simulates the airborne environment necessary to allow verification/certification of proper operation of an aircraft’s TCAS I and II installations.
* Detachable directional antenna
* Large 5.7-inch LCD display
* Simple user interface
* Lightweight at less than 8 lbs.
|
|
|
|
|
|
OMICRON secondary injection test sets and measurement devices are the right choice for Utilities, Industry and Railway as well as for Relay and Measurement Device Manufacturers. The combination of a robust, truly portable, reliable and accurate Hardware design together with the unrivaled Test Universe Software is the basis for OMICRON's ongoing success in maintaining its place as World Leader in the 3-Phase secondary injection test set market.
CMC 356 - Protection Relay Test Set and Commissioning Tool
The CMC 356 is the universal solution for testing all generations and types of protection relays. Its powerful current outputs make it ideal for testing electromechanical relays with high power demands. The integrated network interface also enables the use of the device for testing in IEC 61850 environments with GOOSE and Sampled Values simulation and subscription functionality.
CMC 256plus - Protection Relay Test Set and Universal Calibrator
The CMC 256plus with its extended precision is the most accurate solution for testing protection relays and calibrating all kinds of meters, power quality devices and transducers. It is the first choice for all applications requiring the highest versatility and precision. With its IEC 61850 GOOSE and Sampled Values simulation and subscription functionality it leads the way in testing IEC 61850 substations.
CMC 156 - 3 Phase Voltage / 3 Phase Current Test Set
The CMC 156 is the smallest and lightest solution for three-phase testing of numerical relays, meters and transducers. Weighing only 9.8 kg / 22 lb., it is ideal for applications requiring a high degree of portability.
|
|
SVERKER 750/760 features many functions that make relay testing more efficient. For example, its powerful measurement section can display (in addition to time, voltage and current) Z, R, X, S, P, Q, phase angle and cos ö. All values are presented on a single easy-to-read display.
This is the engineer's toolbox.
|
|
The purpose of power system protection devices is to recognize system faults quickly and reliably and to minimize impairments to the power supply by selectively switching off faulted sections of the power system.
The use of well-chosen protection devices which operate safely and reliably can have a decisive effect on the operational safety of complex electrical networks and plants.
The extent to which the reliability of protection devices can meet expectations depends initially on correct device selection and on the quality of the manufacturer's production process and final test and inspection procedures.
However, only regular testing of protection devices by the user can guarantee that they function correctly throughout their operational life.
These functional tests include the detailed examination of the characteristics configured and the functions used in order to check and, if necessary, restore the availability of the protection devices.
|
|
The 5800 series is a multi-configuration multi-functional test system that is designed to meet the ever changing needs of today's electronic manufacturing environment. An open approach to both hardware and software has been adopted. The open software architecture enables integration with code written using third party software such as Teststand™, Labview™, C#™ and VB.NET™, in short any platform that is .NET compliant.
The open hardware architecture allows configurable chassis and interface styles to accommodate low cost analog in-circuit testing, through to high integrity analog and digital functional test solutions. The integrated 21-slot PXI based backplane enables the user to implement solutions using not only Aeroflex PXI cards but also cards from any PXI card supplier. The 5800 Series of testers comprises three body styles, the 5850, 5830 & 5820.
|
|
|
IPTE develops test equipment, test handlers and turn-key solutions for the automation of testing and adjustments of PCB's and electronic products
|
|
The S790VXI Series2 represents the ultimate high-performance, mixed signal ATE system. Its advanced hardware technology, coupled with CATE software for fast effective program production, makes the S790 Series2 the ideal solution for addressing today's major board test concerns - test program generation,and diagnostic speed and accuracy.
Protecting your investment - with complete S700-series backward compatibility. Fully compatible with all Schlumberger S700 test systems, the S790 Series2 provides a complete, riskfree migration path for all S700 series test programs.
Protecting large investments into earlier S700 test programs and fixtures is, for most users, a major concern. The S790 Series2 protects your investment; its compatible architecture allows existing test programs and fixtures to be loaded and run - simply and robustly - providing an assured, risk-free migration path.
All diagnostic data is also ported, avoiding lengthy and costly revalidation of new or modified diagnostics
|
|
|
|
|
|
ATE QT2256-320PXI system is designed as a Combination Board Tester capable of testing highly complex and dense PCBs employing various test techniques on a single platform.
It can perform Board Level Functional Test through edge connectors of a PCB, and guided probe diagnostics utility to reliably repair Digital/Analog and Mixed Signal PCBs of various complexities for conventional PCBs.
It is an In-Circuit Device / cluster tester when High Current Pin Driver options are installed and interfaced to the UUT either through clips / probes or nail bed. Standard configuration is 64 Channels high current Pin Drivers.
It has in-built 20MHz 12bit Analog Driver / sensors synchronized with digital drivers for covering analog / mixed signal devices.
Integrated Boundary Scan Test controller (Up to 4 Chains) and software package can be used to test today’s PCBs with high density / high pin count devices. Uses latest technology Boundary Scan hardware with RAM based drivers / sensors in synchronization with ATE digital and analog pin drivers.
To effectively test CPU based boards without excluding the CPU from the test, the system offers optional Qmax patented Bus Cycle Signature System.
|
|
|
|
|
|
Fault coverage and return on investment, two major factors affecting the choice of a test system in today's competitive markets.
Combine these with the flexibility to adapt as technology advances and you have the blueprint for the most desirable test system on the market.
From board to program - the solution
PinPoint II 14 slot, has been engineered to meet these criteria. It is the fastest, most economical functional test workstation available, giving the best return on investment in the industry whether configured for diagnostics or functional test.
PinPoint II has, in its high specification and modular design, the stride and flexibility to keep one step ahead of the fast evolving electronics market. It is equally well suited to `one-offs' as it is to production quantities and the combination of test technologies within the one powerful environment provides the key to the diverse range of applications the system is suited to. In-circuit functional test of both analog and digital components, edge card functional, VI analysis, boundary scan, PXI test and schematic reverse engineering can all be included in the same test platform. Flexibility extends further into the interfacing of the tester to the unit under test. The PinPoint II has been developed to adapt to the needs of the customer - clips, probes, edge connectors and bed-of-nails fixtures can all be used.
|
|
Features
Integrated test system
Compact footprint
Fixtures compatible with TCIL-P and TCIL-TS
Compact PLC for internal controls
Visualization and tester interface on external PC (e.g. tester PC) via USB interface
Stand alone operation
Manual width adjustment
SMEMA Interface
Compatibility with all standard test systems
Options
Product specific fixtures
ESD covers
Safety automatic door
|
|
The functional testers with AC timing that has been dominating the market cost in excess of USD300K upwards. The cost of maintaining such a tester is also exorbitant. Ultimately, this increase the final cost of the product.
Qmax latest innovative product, the "No Foot- print" QT2216 Full Functional mixed signal tester is designed to help the semiconductor companies doing final test be more competitive in the following ways:
1. Much lower cost of test equipment
2. No Foot Print means less space needed on test floors
3. Lower maintenance cost
The advantage of the QT2216 is its adaptability. It can be loaded with different modules to alter its configuration for different tests. It can be configured to test ADC including sigma delta type, DAC, digital, opto, linear, high voltage / current devices etc.
|
|
|
SIM-Small Instrumentation Modules-is a compact test and measurement platform for a wide range of applications. Unlike other modular systems, SIM offers complete front-panel as well as remote operation, allowing you to choose between manual and computer control. Up to eight instruments share the same mainframe which provides power, clock synchronization, communications, and module status. For additional versatility, you can cascade mainframes or other RS-232 instruments, and even operate modules outside the mainframe.
|
|
Aaronia EMC Bundle:
Measurement Kit for straightforward pinpointing and measurement
of interference sources
- Pinpointing interference sources
- Estimation of interference field strength
- Verification of shielding and filtering measures
- Identifying faulty components
- Detecting circuitry overly sensitive to interference
It is perfect for locating interference sources which might have
been found e.g. in an EN55011, EN55022 or EN50371 (Class A
or Class B) survey.
|
|
Providing SPEED, ACCURACY and MODULARITY
Supported Standards
* GSM / GPRS / EGPRS
* WCDMA / HSDPA / HSUPA
* Bluetooth®
* AMPS
* TDMA (IS-136)
* CDMA2000® 1xRTT
* CDMA2000® 1xEV-DO
he R&S®CMU300 Universal Radio Communication Tester is a unique solution that combines high-speed, high-accuracy RF parametric testing with layer 1 signaling procedures.
Highlights
* Extremely high-speed testing
* Highly accurate measurements
* Modular future-proof design
* Comprehensive spectrum analyzer and signal generator
* Layer 1 realtime processing
Supported Standards
* GSM
* GPRS
* EGPRS
* 3GPP FDD incl. HSDPA
|
|
|
|
|
|
The GX1110 is a high performance, single-channel PXI arbitrary waveform generator that offers function generator and arbitrary waveform generator functionality within one instrument. Built-in waveforms are available for use with both the DDS or AWG modes of operation and include Sine, Triangle, Ramp, Noise, Gaussian pulse and Sinx/x. A flexible sequencer is also available as part of the AWG's architecture, supporting the generation of complex waveforms.
The GX1200/1201 is a single-channel PXI-based Arbitrary Waveform Generator. The GX1200/1201 is a high performance waveform generator that combines many powerful functions in one small package.
The GX1200/1201 is a single-channel PXI-based Arbitrary Waveform Generator. The GX1200/1201 is a high performance waveform generator that combines many powerful functions in one small package.
The GC1300 is a single-channel PCI-based Arbitrary Waveform Generator. It is a high performance waveform generator that combines many powerful functions in one small package. Supplied free with the instrument is Arbconnection software, which is used for controlling the GC1300 and for generating, editing and downloading waveforms from a remote computer.
|
|
The GP1616H function generator is a programmable instrument capable of generating predefined Sine, Square, Triangle, Ramp, Haversine, Haver triangle and Pulse waveforms as well as a programmable DC output. The firmware is customized to be fully compatible with the Hewlett Packard 8116A GPIB command set. Software test procedures using the original HP8116A instrument require no code modification when upgrading to the GP1616H.
|
|
The GP1550 series features:
- pulse widths from 10nS to 10S
- delays from 0nS to 10S with up to 6-digits resolution.
- Output levels are from -10V to +10V, with pulse amplitudes from 0.5V to 10Vp-p into a 50 Ohm load.
The GP1612H features:
- variable pulse widths from 10 ns to 10 s,
- delays from 0 ns to 10 s with up to 6 digits resolution
- adjustable output levels from -8V to +8V, with pulse amplitudes from .1V to 16Vp-p into 50 ohms load (.2V to 32Vp-p into open circuit).
These Pulse Generators also feature selectable complementary pulse and double pulse, in continuous, triggered, gated and counted burst modes.
They allow selection of predefined amplitude and offset for critical stimulus and testing of major semiconductor technologies as TTL, CMOS and ECL.
|
|
|
The GC1300 is a single-channel PCI-based Arbitrary Waveform Generator. It is a high performance waveform generator that combines many powerful functions in one small package. Supplied free with the instrument is Arbconnection software, which is used for controlling the GC1300 and for generating, editing and downloading waveforms from a remote computer.
|
|
The GTX22x0 family of universal time interval counters provides all the features of stand-alone counters in PXI form factor. There are three versions of the PXI counters, GTX2210, GTX2220 and GTX2230. The GTX2210 support frequency range up to 225MHz, the GTX2220 to 1.3GHz and the GTX2230 covers frequencies up to 2GHz.
The GTX22x0 series counters have two signal input channels via BNC connectors, an external timebase, arm input, and a gate signal output. The separate input signals can be used for Arming and Gating the circuitry, and controlling the timing of the analysis (start/stop duration) for more meaningful measurements.
The GTX22x0 series counters are universal in that they provide many measurement functions of other frequency counters, including frequency, period, and time interval. The GTX22x0 series also have event counting and timing functions over a single channel, such as totalize and ratio between channels.
|
|
QT1100 can functionally test any device working at 5V in in-circuit as well as out-circuit using library defined test patterns. The Visual WorkStation (VWS) mode allows interactive testing of individual devices, as well as wholeboard test. The Device Under Test (DUT) is tested under actual in-circuit conditions, that are available on the board. QT1100 uses the back-driving or node-forcing technique to functionally test devices in-circuit. The back-driving current is limited to 220 mA and back-driving time is limited to 65 m.secs. to comply with the International Defence Standards 00-53/1.
1. In-Circuit Digital Functional Testing
2. Auto compensation with Qmax Simulator
3. Board Learn & Board Test Modes
4. QSM VI – an advanced tool for failure analysis
5. Auto Guarding
6. Logic Analyser
7. Circuit Tracing
8. Developing New Device Program
9. Short Locator
10. RCV Measurement & Oscilloscope
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
