|
|
Manual shape cutting
The P is a lightweight manual ultrasonic device allowing easy shape cutting on any type of synthetic textiles and nonwovens. This handy cutter performs very clean cuts, eliminates frays and creates consistent and clean edges.
Manual straight cutting
The T is an easy-to-handle manual device performing straight cuts on any thermofusible fabric.
|
|
|
2-axis machine which you can program to run any contour or pattern for both welding and cutting applications.
|
|
We are pleased to present our newest cutter, the AutoCut X5. Driven by Servo motors, the X5 offers you significantly faster acceleration along with faster overall cutting speed, meaning greater efficiency and improved throughput for your company.
In fact, while our M3 model is still one of the best and most reliable machines available in the industry, our new X5 can cut up to 60% more in the same time! Repeatable accuracy is 0.02 inches.
A complete, turnkey system includes an integrated vacuum table, gantry and cutting head, and a friendly, easy to use hardware/ software interface.
|
|
| ... products without technical information |
| |
|
Rugged, reliable and powerful, Vemeer concrete cutters can be found working repair and replacement projects on streets and roadways worldwide. Vermeer concrete cutters are perfect for patch and joint placement on interstates, streets and highways. Other applications include cutting highway and bridge relief joints, creating lateral ditches for highway drainage, work on street and airport lighting projects, installation of airport guidance systems and demolition work for widening shoulders and airport pads.
|
|
|
|
|
|
RZ 111 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 110
Blade diameter mm 300 (350)
Engine HONDA Type GX 160
Max. engine power @ RPM kW 4,0/3600
Travel push
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 3600
Water tank capacity l 15
Water supply aqua spojka
Weight kg 55
RZ 120 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 120
Blade diameter mm 350
Engine HONDA Type GX 270
Max. engine power @ RPM kW 6,6/3600
Travel push
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 3400
Water tank capacity l 20
Water supply aqua spojka
Weight kg 95
RZ 121 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 120
Blade diameter mm 350
Engine HONDA Type GX 270
Max. engine power @ RPM kW 6,6/3600
Travel push
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 3400
Water tank capacity l 20
Water supply aqua spojka
Weight kg 72
RZ 170 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 170
Blade diameter mm 450
Engine HONDA Type GX 390
Max. engine power @ RPM kW 9,6/3600
Travel push
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 2800
Water tank capacity l 20
Water supply aqua spojka
Weight kg 106
RZ 171 - ASPHALT AND CONCRETE CUTTERS
Cutting depth mm 170
Blade diameter mm 450
Engine HONDA Type GX 390
Max. engine power @ RPM kW 9,6/3600
Travel ruční
Fastening hole dia. mm 25,4
Max. no-load spindle speed min-1 2800
Water tank capacity l 20
Water supply aqua spojka
Weight kg 78
|
|
|
Floor Saw Blades from TYROLIT and Floor Sawing Machines from TYROLIT Hydrostress - an unbeatable combination.
|
|
|
|
|
|
SHARK CUTTER SUCTION DREDGE
Dredging Supply Company's Shark Class Cutter Suction Dredge features a conventional dredge-operating configuration with modular design for ease of transportation. With standard discharge sizes ranging from 10-inch through 24-inch, our Shark dredges are most commonly used by sand & gravel producers and contractors. The tough yet portable design offers many rewards for the end user. With the proven reliability of the Shark Class cutter suction dredge, the end user can expect a very long life expectancy for this type of equipment. The Shark dredge will provide a high percentage of uptime and availability, which makes it one of the best selling models in the world!
DSC's Shark Class Dredge features standardized systems throughout all of the various sizes and configurations. The operating systems are all PLC based and offer the operator an ergonomic and user-friendly control panel. With the simple touch of a few switches, you are off and dredging. The Shark dredge also features power up/down spud systems with API rated winch drums for proper cable storage.
|
|
|
|
|
|
Features:
» Handling of two LVDT transducers, for continuous and interrupted surfaces gauging.
» Compact size.
» Bench and built-in versions.
» Application customisation by the user through the set-up of:
- Gauging formulas;
- Arms ratio for self-learning;
- Metric or British measurement units.
» Analogue indicator for the continuous measurement
display, with x1 and x10 automatic scale change.
» Digital I/O, SINK or SOURCE type, for the connection to CNC/PLC.
» The operator's panel provided with sensitive waterproof sandwich keyboard allows:
- Setting the three gauging thresholds for the output contact;
- Setting the delay of cycle start input contact and zero quota output contact;
- Setting the zero correction value (offset);
- Selection of the reading of individual transducers for the mechanical manual zeroing;
- Measure electronic, manual and automatic zeroing.
» Memory and LEDs test performed at start-up.
Advantages:
» Accurate.
» Simply to configure and to programme.
» Can be integrated in any architecture both in a new machine or in an already operating machine.
» Comfortable to use.
» Tough and reliable.
» Affordable.
|
|
Features:
Overall dimension: 20x40x76 mm.
Measuring range: up to 12,5 mm
Repeatability: < 0,05 µm.
Connection to the electronics through cables long up to 30 m
Memory chip for process optimization.
Pneumatic recoil.
Quick manual retooling of the fingers.
Wide range of fixed or manually adjustable supports.
Fingers available with breakaway pin.
Advantages:
COMPATIBILITY
Fits all measurement applications related to:
- diameter
- position
on new or operating machines
No limits of installation due to the loss of the signal.
ACCURACY
Within the measuring range:
- sub micron, through automatic calibration on the master for every measure.
- micron, through automatic calibration on one master only for all measures.
PRODUCTIVITY
No manual retooling within the measuring range.
Quick manual retooling for adjustment to a new family of pieces.
Prevention from machine breakdown due to accidental impacts.
|
|
Features:
Resolution: 0.1 µm
Linearity: +/- 1 µm (Diameter)
Linearity: +/- 0.5 µm (Position)
Standard gauge fingers for measure of diameters from 5 mm to 90 mm.
Watertight.
Measure of smooth or interrupted surfaces.
Gauge slides driven by air or oil.
Fine adjustment on slide.
Wearproof fulcrums.
Advantages:
Accurate.
Sturdy, suitable for installation on grinders.
Fits pre-, in-, and post-process applications.
Quick set-up and retooling.
|
|
PART AND TOOL MEASUREMENT APPLICATIONS ON CUTTING MACHINE TOOLS.
Automatic on-machine gauging of workpiece allows time saving in part coordinates setting as well as to detect in real time the result of your machining. Spindle and turret probing systems, provided with several types of wireless transmission systems (radio, infrared, high frequency) are available for this purpose.
Tool setting on lathes and machining centers are provided with dedicated probing solutions, both for automatic and semi-automatic cycles.
Non-contact laser tool checking is also available for tool breakage, tool integrity and tool profile measurement on milling machines and machining centers.
|
|
|
The highly polished open flute not only allows for easier chip formation and evacuation, but also provides for a sharper cutting edge that delivers a better edge finish on a variety of materials. Our premium micro grain carbide allows for superb wear resistance and tool strength. Special point geometry contributes to improved bottom finish and plunging capabilities. Tools are available in upcut and downcut versions from 1/16" through 3/8" diameters.
|
|
Onsrud is proud to announce the launch of our NEW taper tools. These cutters are made of premium micro-grain carbide and are available in a variety of sizes, lengths, and angles.
The tools are available with a ball nose tip giving them the flexibility to cut draft angles in molds to 3D decorative profiles. The cutting geometry will allow them to cut a variety of materials and produce a good edge finish.
Custom tools can be made upon request.
Material: Wood, Plastic, Aluminum
|
|
The cutter pumps of the series SFC are capable of cutting aluminum chips and similar materials and pumping of these materials along with the coolant fluid. An agitator located at the pump suction helps to break up and separate any large bundles of chips or birds nests which reach the pump suction.
Axial / semi-open impellers
Large chips
25 ... 1800 l/min
4 ... 35 m
|
|
MultiStream Pumps with adjustible single-channel impeller
MultiStream-pumps are suitable for handling effluent or sewage in municipal and industrial pumping stations as well as in surface water drainage applications. The smaller types are also used very successfully as portable units to deal with emergency situations. The sewage pumps UAK are suitable for handling water without faeces. In hazardous locations or in case the pumps are connected to the public sewerage we recommend our explosionproof sewage pumps UFK
Recommended for:
- effluent which contains fibrous matter
- mixed water
- effluent which contains solids
- rainwater
- raw effluent
- raw sludge
|
|
| ... products without technical information |
| |
|
Double E offers core cutters in manual, semi-automatic and fully automatic models. Each model cuts cores efficiently and quietly without creating sawdust. The machines accept cores with diameters ranging from 38 mm (1.5") to 200 mm (8"), and wall thickness up to 20 mm (.75"). A simple and quick modification allows the machine to switch between various core ID’s.
|
|
|
It represents an ideal equipment for the agglomeration, granulation and mixing of food, chemical and pharmaceutical powders. It is successfully used in the additivation ( flavouring, colouring, etc.) and encapsulation of mixtures or powdery products thanks to the proved uniformity and homogeneity of its fluid-bed process. Its use is suitable for thermosensitive products. It is available in several construction materials.
|
|
OYSTAR Hüttlin fluid bed systems have a modular design. The base devices are designed as heavy-duty 10 bar or 12 bar excess pressure lines and can be adjusted using various different options.
Depending on the application required the Oystar Hüttlin fluid bed system can be configurated as:
HD Hüttlin dryer
HDG Hüttlin dryer granulator
HDGC Hüttlin dryer granulator coater
OYSTAR Hüttlin concept solutions mark a clear move away from the conventional technology of the past almost 40 years. The different detailed solutions such as the Diskjet, the spraying system, the dynamic filter and the gas analysis for organic processes involve major process advantages that greatly benefit the user.
|
|
|
AP Series automatic polishers are designed for time saving purposes, when it is requested the preparation of a certain number of metallographic samples simultaneously or, where the large number of samples justifies the choice of an automatic machine.
|
|
|
|
|
|
High Speed Cutting and Jig Grinding with very high precision in one machine
Simple programming of the machining cycles for jig grinding
Grinding technology fully integrated (contact measurement of the abrasive pin, dressing spindle, grinding oil, CO2 extinguishing system etc.)
High precision of machine due to combined use of linear motors and absolutely friction-free hydrostatic guides in all axes
Maximum feed rate and acceleration limited to achieve highest possible precision
Outstanding damping characteristics due to hydrostatic system oil film in all axes
Friction-free counterbalance in the Z-axis
Extremely rigid machine construction, 11 t weight
Three-point support, damping machine feet
Precise control of all temperatures in the machine, including the cooling water, the oil for the hydrostatics and the oil for the machining, cooling of motors and secondary magnetic elements, extra cooling housing for spindle
Cabin completely closed, includes noise reduction and large windows with security glass, loading with crane possible
Infrared touch probe for work piece set up and 3D measurement of the contour
Chip disposal via 2 spiral conveyors into chip box behind the machine
|
|
|
|
|
|
HSM CARDBOARD SHREDDERS
Cardboard recycling for despatching and warehouse areas
HSM Profi Pack 400 and 425 are the ideal solution for all despatching and warehouse areas. They instantly convert bulky used cardboard containers of goods delivered into an all-purpose and first of all free packaging material.
> Cutting and perforation in one cycle meaning time-consuming pre-cutting of cardboard no longer required
> The hardened cutting rollers, made from a single piece of metal, are completely resistant to damage from paper clips and other soft metal items
> The special geometry of the cutting rollers guarantees even, optimum padding of the material
> Specially hardened perforating rollers and sturdy bearing plates guarantee reliable padding without bending, twisting or catching in the cutting unit - thus extending service life and saving subsequent costs
> The sturdy housing made of sheet steel has been specially designed for the rigours of use at the despatching area
> The practical measuring scale allows you to quickly measure the width of material you require
> A generously proportioned supporting table ensures comfortable and simple operation
|
|
he Easypack Shredder™ box shredder trims surplus cardboard boxes of any size, and up to 15 mm total thickness, automatically without the need for pre-cutting. The ruggedly constructed machine is mounted on castors, for ease of positioning, and has an easily cleaned stainless steel finish. A powerful motor provides high speed cushion production.
* High volume output 6 cubic metres per hour
* Lattice structure makes strong, resilient pads
* Highly environmentally friendly
* Cost effective and efficient
* Fully recyclable
|
|
Function
The ALD 01 laser depaneling system is equipped with a rotary table system for optimum separation of the individual processing stages. This method allows parallel processing of the individual tasks. Consequently, the only times relevant for the cycle time, are the time for the longest individual stage plus the time taken for the table to rotate from one position to another.
1. Handover of the panel from the inlet conveyor to the first position on the rotary table
2. Panel routing
3. Loading of individual routed PCBs onto the outlet conveyor
4. Tipping of remaining panel waste into the integrated waste container
The panel is transferred from the inlet conveyor to the first position on the turntable by means of a pneumatic X/Y/Z portal gripper system. The routing process utilizes a CO² Laser.
|
|
Laser Depanelizer for stress free and flexible Cutting of PCB Panels
- Depanelizing with Laser Technology
- Stress- and dust free Process
- Low Process cycles, high throughput
- Simple Fixtures
- Cutting and Marking possible
- Cutting any shapes
|
|
|
|
see the results for the following category : 
