|
|
|
|
|
|
The Webster DHM 3 Series Digital Hydraulic Multimeter is an all-in-one unit designed to test the performance of hydraulic pumps, motors, valves and hydrostatic transmissions.
The easy-to-use design allows the operator to just switch on and test, without complex setup or special training.
The DHM measures flow, pressure and temperature. In addition, the DHM holds the peak pressure value as well as calculating hydraulic power and volumetric efficiency using the unique P-Q test button.
The DHM is the ideal tool for pinpointing hydraulic system faults, reducing downtime, and helping in preventative maintenance. The design builds on the very successful Webster DHT range of portable testers with the addition of a large digital display and a built-in pressure transducer.
The turbine flow meter with built-in loading valve is bi-directional and specifically designed to enable the operator to simulate the maximum working pressure safely during normal machine operation.
The loading valve has safety discs built-in to protect the operator and the multimeter in the event of excessive pressure, allowing oil to bypass the loading valve INTERNALLY with no spillage of oil from the hydraulic circuit, eliminating any danger to the operator or environmental hazards.
|
|
The Webster HT 2 Series Analogue Hydraulic Testers are designed for testing hydraulic pumps, motors, valves and hydrostatic transmissions. This easy to use diagnostic unit can pin point hydraulic system faults, reducing downtime and help in preventive maintenance.
Accurately measuring flow, pressure and temperature, testers are ideal for conveniently checking, hydraulic system performance or locating faults while operating directional control valves or adjusting valve settings. Webster turbines are designed for continuous monitoring or intermittent use commissioning and servicing hydraulic systems up to 480 bar, 7000 psi pressure.
The pressure loading valve with internal by-pass safety discs, allows progressive build up of pressure to check the flow throughout the working range.
|
|
The Webster DHT 1 Series Digital Hydraulic Testers accurately measure flow, pressure and temperature. Webster testers are designed to conveniently check the performance of hydraulic pumps, motors, valves and hydrostatic transmissions.
This easy to use diagnostic tester has simplified controls and can pin-point hydraulic system faults, reducing downtime and helping in preventive maintenance. The tester comprises a turbine flow block and a large easy to read digital display which indicates both flow and temperature.
The tester has a built-in loading valve to simulate the working pressure during normal machine operation. The built-in safety discs protect the machine and operator in event of excessive pressure, allowing oil to safely bypass the loading valve INTERNALLY with no spillage of oil from the hydraulic circuit, eliminating clean-up costs and environmental hazards.
|
|
The PFM6 Series is a compact, lightweight digital
portable tester designed for fast diagnostic
troubleshooting of all types of mobile or
stationary hydraulic systems and components.
These self-contained testers feature laboratory
accuracy and provide fl ow, pressure and
temperature measurements simultaneously
from one point.
Carrying handle for improved portability
Bi-directional model available
|
|
|
|
|
|
The leak detector ET97W represents the best solution on the market in terms of precision, flexibility and execution speed of seal tests with measure in flow rate.
This instrument allows to measure in a direct way the air flow generated by the leak-off rate.
ET97W is composed of a pneumatic circuit optimized in order to reduce the filling times, of a mass flow sensor, of a pressure
sensor and of an electronic pressure regulator, that guarantees stable and safe test pressures without the operator assistance.
The instrument detects the leaks through continuous seal measure of the pressurized piece, this method allows to reduce
drastically the time of the test phase.
ET97W is specially used in seal tests where the volume of the piece is unknown and variable (oil motors, elastics bags or
bottles), when the leak entity is so elevated that a Äp system does not succeed to maintain constant the test pressure (cartridge valves, oil distributors, between filaments) and finally when is requested a continuous leak measurement in order to allow the operator to look for and repair the same one.
|
|
|
|
|
|
The historic problem of flow test systems, especially for high flows, deals with keeping the
reference pressure regulated according to the wanted one while the flow changes.
The flow measurement depends directly (but not linearly) on the pressure and because of charge loss, we have to consider as pressure value the pressure at the entrance of the piece and not the one generated inside the piece.
In the past almost all leak and flow test producers tried to solve this by separating the connecting tubes to the piece between flow and pressure measurement in order to obtain at least a real pressure datum (even if not regulated) and by correcting through the software the eventual charge loss of connection tubes through correlation calculations.
The limits of this method are (especially with high charge loss -> 5 Lt/min) in the non linearity of flow/pressure.
Moreover in deforming pieces, where the pressure value modifies the matched flow value (packaging, filters, valves … and every piece which is not really rigid) this correlation changes drastically the wanted measurement value.
Through new proportional techniques about electronics and algorithm able to take a picture of the flow value (only at wanted values of pressure), the RFO techniques is a warranty of doing tests at the flow and pressure values you set.
|
|
DELTA F is an electro-pneumatic equipment able to measure the air flow rate and the generated pressure through the piece in test.
The output pressure control assure the test is always performed on the same condition.
The equipment can be used manually or managed by a PLC or Personal Computer.
So it can be used also with automatic system in every industrial situation.
* 16 programmable test parameters tables: each table includes all the parameters defining a test cycle so it is easy to make predefined test setting for different products
* Selectable pressure measurement units
* Selectable flow measurement units
* Selectable languages for display messages
* Print out of customized test report (with external RS-232 printer)
* RS422 serial line MODBUS protocol for PC supervisory system
* Opto-isolated interface with PLC
* An aided procedure making it possible to calibrate the pressure sensor
|
|
The LCT-01 is the world's most popular portable Load Cell Tester.
It is a stand-alone portable hand-held device that was especially designed to help technical people immediately analyze the condition of strain-gage based load-cells.
The LCT fits all common types of load-cells available in the market today: four wires, 6 wires (with sense) and all rated gain outputs.
It provides the user with the essential data needed about the conditions of the tested load-cell, such as physical distortion (possibly caused by overload, shock load or metal fatigue), and electrical conditions (bridge resistance, shielding and resistance to ground).
The LCT allows the user to test the load-cell whether it is installed or removed. The unit is fully computerized and battery operated. A 16 x 2 alphanumeric LCD display guides the operator through all test stages and clearly displays the results.
|
|
|
For axial loads, load cells are commonly used. Where a standard cell is not available or will not perform, Teledyne Brown may be of assistance. We will design and manufacture a Custom Load Cell to unique requirements such as harsh environments, limited space, or high-overload conditions.
|
|
|
Load Pin Transducers (also known as Shear Pin Sensors) measure loads using a strain gage element sensitive to shear loads. Using a laboratory calibration traceable to NIST, shear strain is related to load. Typical sizes range from 5/8 inch to 3.5 inch diameter. Two-component output is available for applications where loads are in the X & Y planes.
|
|
|
It is often the case that torque in a rotating shaft can be measured with a stationary, reaction torque sensor at some point in the powertrain. This is due to the existence of an equal and opposite force (torque) necessary to hold the drive and driven equipment in place.
|
|
|
Bonded foil strain gages are the time-honored standard for measuring torque and force on mechanical components. Based on many years of experience with this proven technology, Teledyne Instruments offers a variety of torque sensors and load cells for factory, laboratory, and field testing.
|
|
|
|
|
|
Rigid Pendulum Type Physical Properties Testing Instrument, RPT-3000W
This instrument allows measurement of visco-elastic physical properties under a curing process and the surface layer physical properties of the material being measured and other materials such as inorganic materials like concrete, cosmetics, paper and foods. This means that the test method does not depend on the substrate. Therefore, this instrument has applications for the development/improvement, quality evaluation, designing, trouble-shooting, and the production line and life evaluation of materials.
All materials transform from a liquid state to a solid state through certain actions (heat, light, time and others) and produce various physical properties. The change in phase from a liquid to a solid causes various problems. The most important item to evaluate from among the various material evaluations is the change in age of the chemical-physical performances in the process of curing and drying from a liquid state to a solid state.
Measurement
Fix the test piece coating plate on the cooling/heating block. Set the pendulum so that the knife-edge, the fulcrum of the swing, comes vertically into contact on the test piece coated surface. Apply free vibration to the pendulum. For measurement of physical properties, use a cylindrical edge. By analyzing this vibration, the curing process and surface's physical properties can be evaluated.
Features
-Coating Thickness Resolution: 0.01 ìm - 7mm
-Period of Vibration:0.05 to 2.000sec
-Logarithmic Damping Ratio: 0.001 to 6.000sec
-Test Temperature: -100 to +400 degree Celsius
-Measurement Time: 1 to 9999 minutes
|
|
Go! BD S11 for BD-RE and BD-R
Go! BD S11 is a production control tester for BD-RE and BD-R, single- and double-layer. Go! helps manufacturers increase the number of tested discs and achieve better control of the production process.
Key features
• Support to analyze BD-R/RE SL/DL disc formats.
• SpeedScan measurement method.
• External Write support for most major drive brands:
- Set writing speed
- Set writing power
- Make automatic DOW cycles and power series
• Supports the use of A21 autoloader.
• Integrated database.
Key benefits
• Optimized for repeatable measurements in order to detect variations in
produced media.
• Cost effective tester optimized to work together with the CATS reference
tester.
• Based on a selected consumer drive for best analysis.
• Analyzes the discs’ recording quality through external recording drives.
• Easy, reliable operation using special user interface designed for production
|
|
|
This tester is suitable for measuring creep which occurs instantaneously and creep which increases with time when the material subjected to a constant load is left to stand under a specified temperature.
|
|
BPA 5
Ready-to-Go-Set to determine the temperature at which a bitumen tends to break rather than to flow when stressed.
The Fraass-Breaking-Point is the temperature at which the first cracks appear in the coating.
It can be applied for any homogeneous road or industrial bitumen.
|
|
|
|
|
|
The ETA-GT II geometrical tester is a compact measurement system for all stages of disc manufacture - including stamper verification, half-disc and bonded discs.
It enables all relevant geometrical data to be determined, including the inner hole and the lead-in and lead-out diameter. The disc tray permits measurement of disc eccentricity relative to the inner groove (lead-in) as well as to the outer groove (leadout). With its easy-to-use, intuitive user interface, it provides a graphic representation of accuracy for measured geometrical data such as eccentricity, unroundness and layer shift of optical
discs or stampers.
While the ETA GT II serves CD as well as DVD, the ETAGT II / Blue provides one measurement system for all formats CD/DVD/BD.
KEY BENEFITS
- Geometrical tester for all stages of disc manufacture,
from stamper verification to molded CD or half discs to
bonded DVD and BD (optional)
- Measuring all cases: Prerecorded, recordable and
rewritable
- Ready for Blu-Ray single and dual layer discs (ETA-GT II
/ Blue)
- ETA-GT II (CD/DVD) upgradable to ETA-GT II / Blue
(CD/DVD/BD)
- Evaluation of eccentricity and unroundness
- Layer shift evaluation for dual-layer DVDs and BDs
- Evaluation of inner hole, plus inner and outer groove
diameter
- Indicator axes for adjustements to compensate eccentricity
|
|
|
|
|
|
A&D's pipette accuracy testers provide a simple, precise, and cost-effective means for managing the accuracies of your pipettes by yourself.
The testing procedure is based the gravimetric method, which is the most commonly used test for the accuracy of variable-volume pipettes and is recommended by the ISO8655. In the gravimetric method, pipette volume is determined based on the mass value of the distilled water dispensed from the pipette. The high precision, accuracy, and speed of A&D's balances therefore ensure as effective testing as possible.
A&D’s pipette accuracy testers are equipped with various devices to facilitate your testing. Firstly, the evaporation trap, which prevents the evaporation of the dispensed water by maintaining high humidity inside, can minimize errors due to loss of evaporation. Secondly, the entire pipette accuracy tester set can be packed in a portable carrying case. This makes it easy to perform tests on-site, instead of collecting all the pipettes at one site for testing. Finally, the WinCT-Pipette software automatically converts mass values into volumetric values using the liquid temperature and barometric pressure previously entered. It is also possible to print an A4 or letter-size report including test conditions, data, judgment results, etc.
Three models are available depending on what volumetric range is to be measured. With A&D’s pipette accuracy tester, you can now easily and correctly screen out pipettes that need adjusting or repairing, eliminating the unnecessary costs of having all your pipettes inspected regularly by an outside contractor.
Please see the Pipette Accuracy Testers catalog for further details.
|
|
|
|
|
|
Laboratory volume standard Seraphin Test Measures
Laboratory Measures Series C: Bottom Drain Slicker Plate Measures
These small drain bottom measures are designed specifically for accurate testing of small meters and testing the accuracy of other measures in a metrology laboratory. Specifications and outstanding features include a neck that is machined perpendicular to axis so that excess liquid can be sheared off by sliding a slicker plate across the top of the neck; a stainless steel quick closing butterfly drain valve and an overflow trough.
High Accuracy Neck Series M: Bottom Drain Graduated Neck Measures
These small drain bottom measures are The "High Accuracy" type neck has at least 1.5% of the prover volume and a smaller diameter to achieve greater neck volume resolution. This Series M Prover has all the outstanding features of the Series J. Due to the greater resolution it is a favorite of laboratory meterologists. Seraphin® Series M provers come standard with a three piece S/S ball valve. Our Series M & C provers are sent to a NVLAP facility for calibration to assure NIST traceability with uncertainty values. Other types of calibration are available.
|
|
|
Moving up in the heavyweight class, Seraphin® produces heavy duty provers for testing tank trucks, containers, testing tanks and large volume meters. These are all made with the same accuracy and attention to detail and quality as the smaller test measures. A prover has a bottom drain and a graduated neck . Seraphin® provers are easy to use, reliable, and low cost way to measure the output accuracy of liquid metering equipment. All Seraphin® provers are manufactured of type 300 Stainless Steel eliminating the interior coating required of carbon steel models and therefore are corrosion resistant over an indefinite period of time. Many Seraphins® are still in use after decades of use. They are built and calibrated to the latest OIML R-120, Measurement Canada, API and NIST handbook 105-3 standards. Seraphin's® provers are used world wide and are considered the de-facto leader in the industry.
|
|
|
The Seraphin skid prover system is made up of a precision volumetric stainless steel Prover connected to a pump-off system and mounted on skid. The prover drain valve is plumbed to piping that can be routed via butterfly valves to a gravity drain or to the pump. A manual hose reel, with hose and nozzle, is connected to the pump. The hose is used to route the petroleum to an above ground storage tank or up into a tank truck.
|
|
Conventional AC test transformers are especially designed for testing objects of medium capacitance. These systems are particularly suited for tests requiring stable voltage even if the load changes under voltage (corona, wet & pollution tests) or when the load is inductive (inductive voltage transformers).
The possibility of stacking several of these transformer modules allows reaching very high voltage levels by keeping reasonable floor space.
|
|
| ... products without technical information |
| |
The newest member to Hanna instruments Combo series of combination waterproof testers with advanced functions is HI 98121, designed for simultaneous pH and ORP measurements.
HI 98121 also reads temperature, which is continuously displayed on the dual level LCD.
An encapsulated external stainless steel sensor, positioned in close proximity to the pH electrode provides fast response. A fiber junction can be easily pulled out and replenished. And when finally spent, the pH electrode cartridge can be quickly replaced with the supplied electrode removal tool, reducing waste and cost.
HI 98121 works with common batteries and when turned on, displays the percentage of remaining battery life. The stability indicator ensures reliable readings.
Ergonomically designed for ease in handling, this meter will float if inadvertently dropped into water.
|
|
|
Checks the operating condition of an IR & HF remote control before "condemning" the equipment on vehicles, such as centralized suppression, alarm, etc.
|
|
The module VE0006 is a system for the evaluation of luminous objects in the visible area of the light. For this purpose, colour and luminosity are evaluated independently, according to user-specific instructions. Thus, the module is especially qualified for the function test or the qualitative selection of LEDs.
Technical data:
- Test parameters color and intensity
- Power supply 12-30V DC
- Wavelength 400nm up to 700nm
- gain steps 6
- Resolution 12 bit for each gain
- dynamic >90 dB
- Serial and parallel interface useable in parallel
- Cycle time approx. 23ms for 1 product
|
|
|
|
see the results for the following category : 
