|
|
The Elliott Digital Governor (EDG) is a compact, cost efficient, packaged electronic speed control unit for precise, reliable speed control of mechanical drives or induction generators. The EDG has simple push-button control to provide improved reliability and speed control over hydraulic governors without the use of wearing parts such as linkages and bearings. Additionally, it does not require a separate programmer as required by many other speed control methods.
The EDG has numerous standard design features including a large, continiuous LCD display and a wide, continuously adjustable governing range from 200-10,000 Hz. Idle speed, ramp rate and turbine speed are programmable, while electrical trip speed is pre-programmed. Optional features include remote trip and start/stop capabilities. The unit is sized for 19-inch rack mounting and can be configured for NEMA A or NEMA D operation. The standard enclosure is NEMA 4X and is suitable for wall mounting.
|
|
DST2600 is a compact and affordable gen-set controller system for power up to 40kVA.
DST2600 makes available all the functions of a traditional gen-set stand-by panel: full AMF controller with engine and generator protections, contactors for power transfer, battery charge maintainer, power relays for engine commands, measurement systems and display for electrical and other physical quantities.
|
|
|
Tide Powercon electronic intelligence power controller has inlaid high performance computer chips and various functions, such as measurement, control, protection and remote control all in one, and the controlling program and protective parameters can be changed, completely satisfying requirements of users and professional assembly factories on automatic control of different generator sets.
|
|
|
|
|
|
TEM10 are mounted on canopies. They allow the Manual and Automatic operation and the removal of power through alternator by socket protected by switches.
The degree of protection is IP55 in the command part, while it is IP44
in the socket place (IP 55 is an optional and it can be requested with special sockets).
These panels are suitable for being used daily in a generator in safety. Actually, they are characterized by sturdiness, components reliability and a lot of care during assemblying phase. A 10 poles connector (which is placed on the front part of the sockets panel) ,allows to connect to a Mains/generator transfer switch panel (i.e. ATS-E) managed by the Control Panel.
These panels are equipped with all it is necessary for their installation: bolts, power cable to connect to alternator (up to 125Amp), metal plug to be inserted into the panel to connect the engine cables.
They use an electronic device which is named TE806. It is simple and reliable. It is also homologated for being used in the most severe environments with maximum security. All controls related to mains and generators electrical measures and all engine controls are shown on a 4 led digits display. It is an easy and powerful device with a lot of available functions.
|
|
Generator Paralleling Controller – GPC-2
Compact all-in-one control unit designed for applications programmed in a PLC. The GPC-2 contains all necessary functions for protection and control of a synchronous/asynchronous generator along with all necessary galvanically separated 3-phase measuring circuits.
The GPC-2 is intended for land-based applications. It is designed for the following applications (can be combined):
> Stand-alone
> Parallel with other generators
> Parallel with the mains
The GPC-2 can synchronise the generator and after synchronisation carry out all necessary generator control and protective functions. It is well-suited for PLC-controlled systems and the interfacing can be done via binary and analogue I/Os or via (optional) serial communication.
|
|
Generator Paralleling Controller – GPC-2
Compact all-in-one control unit designed for applications programmed in a PLC. The GPC-2 contains all necessary functions for protection and control of a synchronous/asynchronous generator along with all necessary galvanically separated 3-phase measuring circuits.
The GPC-2 is intended for land-based applications. It is designed for the following applications (can be combined):
> Stand-alone
> Parallel with other generators
> Parallel with the mains
The GPC-2 can synchronise the generator and after synchronisation carry out all necessary generator control and protective functions. It is well-suited for PLC-controlled systems and the interfacing can be done via binary and analogue I/Os or via (optional) serial communication.
|
|
DST4601/PX is the evolution of SICES renowned DST4601 AMF controller.
Aimed particularly to parallel application, thanks to its high degree of configuration, it can easily be used in quite all standard and special gen-set applications.
Born to manage the last generation of electronic engine, it supports CAN interface toward quite all most popular engines: J1939 protocol for VOLVO, SCANIA, DEUTZ, PERKINS, CAT, IVECO and MTU protocols for MTU engines.
A large graphic display, with a resolution of 240x128 pixels, allowed to implement a simple to use operator interface that is able, at the same time, to report an huge number of electrical and engine measures and information. Engine troubleshooting now can be made by textual interface (for example all MTU diagnostic codes are translated in plain English text).
|
|
|
It is an easy, sturdy and practical manual panel for generating sets control. It is easy for inspection. It is made in a metal box. It is provided with anti vibrating camping pads. It can be directly connected to the alternator.
|
|
| ... products without technical information |
| |
Control, display and regulation devices are assembled in a clear layout in 8146 series control stations. The number of units fitted depends on the control station size and the space required to fit each device. It is not possible to standardize this.
Explosion protection to CENELEC, IEC
Can be used in Zone 1 and Zone 2, Zone 21 and Zone 22
Enclosure in glass fibre reinforced polyester resin, in galvanized sheet steel or stainless steel
Different enclosure sizes
Different enclosure heights
Can be combined to larger units
Equipped with built-in units for snap-in fitting (control units, indicating lamps, illuminated buttons, control switches, ammeters, voltmeters
Different options (Flanges, Cover hinges, Flanges enclosure, Brass plates for metal cable entries)
|
|
|
The THOR M8 transmitter is equipped with up to 8 single-axis joysticks and is specifically designed for machines moved by proportional electro-hydraulic valve banks such as, 7-8 functions hydraulic cranes, crawler lifting machines and other special machines. In addition to the 8 single axis joysticks, the very wide THOR console has room for several on/off and proportional commands making it an easy to customise the system for complex DC powered applications.
|
|
|
To satisfy all the functions normally required by a numerical control, OSAI have introduced a new operator console that can be connected to the CNC either through the new OS-WIRE proprietry bus, or the standard CANOpen interface. With the combination of WinMedia + operator console we offer an imaginative and innovative example of a numerical control “front end”. As well as the ability to customise the existing pushbuttons, in the electronic interface with standard components, the flexibility of configuration to suit the entire operator interface for most types of application is guaranteed.
|
|
Portable Transmitter Console RC7
RADIO REMOTE-CONTROL FOR INDUSTRIAL EQUIPMENTS, CRANES, HANDLING MACHINES, CABINS,…
Light, compact and ultra-tough case.
Up to 30 ON/OFF and/or 7 proportional channels.
Plug-in Lithium battery (long lasting, 4 h charge).
Personalized controls and control panel.
TRANSMISSION:
European ISM band, license-free use, radiated power 16h in continuous use, recharge: 80% in 2h, 100% in 4h.
Charger: power supply 12/24Vdc or 110/230Vac, cord 1.2m.
Ambient temperature during charge: +5 to +50°C.
Signaling on charger: 1 Led = power supply, 1 Led = battery charge level (fixed during charge from 0 to 80%, flashing from 80 to 100%, unlit: battery charged).
MECHANICALS:
Elastomer-filled polyamide case measuring: 160 x 240 x 150mm, weight: 1.6Kg.
Nylon strap.
|
|
|
The intelligent teach pendant (ITP) is a portable console unit that can be connected to the 10 Series CNC system to so that the operator can input and output typical system commands. The ITP is also available with a mushroom emergency stop pushbutton and a “live man” switch to ensure safety when in use.
|
|
| ... products without technical information |
| |
|
|
|
|
OPTISPARK is the integrated control system developed in cooperation with Cannon AUTOMATA. It consists of two sections: an integrated control system and the user panel (Human Machine Interface).
The integrated control system performs many functions usually carried out by several components such as steam pressure, water level, alarm data acquisition, and it sees to thermal efficiency with the aid of the most advanced control systems: combustion control through electronic cams, control of the oxygen trim, of the flue gas re-circulation and of the air fan by means of an inverter.
The H.M.I. features are: synoptic screens with multi-language
texts; high-resolution colour touch screen display; real-time and historical tracking of selected process trends; alarm reports log; navigator system; multilanguage editor.
OPTISPARK connects to the modern communications systems: it sends SMS and e-mail in case of alarms event; it is displayed on both the Intranet and the Internet; it connects to supervision systems via OPC server.
OPTISPARK's main benefits are: the performance equivalent to the most advanced DCS systems at a lower cost, the optimised combustion, the reduction of environmental impact, of fuel and energy consumption, and of the time for starting and checking the boiler.
|
|
|
|
see the results for the following category : 
