|
|
|
|
|
|
VORTEX® 2-WAY SEAL TITE DIVERTER
The Vortex® 2-Way Seal Tite Diverter is designed for use in gravity flow applications where material can be diverter from one source to either of two destinations. 3-way model available.
The Seal Tite Diverter offers a removable access door for replacement of blade and shaft seals. All internal ledges have been eliminated to promote cleanliness. The Seal Tite Diverter’s superior design promotes efficiency, durability, and long service life.
Valve Specifications
- Size/Bore Options: 100mm to 750mm Diameter Round, Square, or Rectangular
- Media: Powder, Pellets, Granulars
- Connection Options: SVC Standard Flange, ANSI, DIN, JIS, or Custom Flanges
- Media Temperature: Up to 82°C continuous to 121°C intermittent service, Modifications up to 204°C continuous to 232°C intermittent service
- Media Pressure: 0 barg, Gravity Flow Only
- Metal Construction Options: 304 or 316L Stainless Steel, and Carbon Steel
- Seal/Seat Material Options: Nylon, PET, UHMW, Glass Filled Teflon, Natural Rubber, Kryptane, and/or Silicon Rubber
- Drive/Actuation Options: Double Acting Air Cylinder, Electric Actuator, or Hand Lever
- Position Confirmation: Magnetic Reed Switch, Proximity Switch, or Mechanical Switch
- Compliance/Approvals: CE, ATEX, FDA
- Industry Use: Plastics, Petrochem, Chemicals, Foods, Minerals, Textiles, Agriculture
|
|
|
|
|
|
VORTEX® QUANTUM SERIES 2-WAY WYE LINE DIVERTER
The patent pending Vortex® Quantum Series Wye Line Diverter is specifically engineered to handle dry bulk solids in vacuum or dilute phase pneumatic conveying systems with pressures up to 15 psig (1 barg). 3-way, 4-way, and Multi-Port models available.
A full flow orifice provides unrestricted conveying of material with no disk or ledges to impede flow. The diverter seat and live-loaded seals are shielded from abrasion by a metal insert, which provides superior shearing action.
The Wye Line Diverter is designed to eliminate problems, enabling you to meet your objectives by increasing production, while decreasing labour and equipment costs.
Valve Specifications:
- Size/Bore Options: 50mm to 125mm Diameters Pipe, 50mm to 150mm Tube. Consult Factory for 150mm to 300mm Pipe, 200mm to 300mm Tube Models
- Media: Powder, Pellets, Granulars
- Connection Options: ANSI, DIN, JIS, or Compression Couplings
- Media Temperature: Up to 82°C continuous to 121°C intermittent service, Modifications up to 204°C continuous to 232°C intermittent service
- Media Pressure: -0.1 MPa +0.1 MPa, 1 barg, 15 psig, depending on size
- Metal Construction Options: 304 or 316L Stainless Steel, Aluminium, and/or Carbon Steel
- Seal/Seat Material Options: Nylon, PET, UHMW, Glass Filled Teflon, Natural Rubber, and/or Silicon Rubber
- Drive/Actuation Options: Double Acting Air Cylinder, Electric Actuator, Handwheel, or Chainwheel
- Position Detection: Magnetic Reed Switch, Proximity Switch
- Compliance/Approvals: CE, ATEX, FDA
- Industry Use: Plastics, Petrochemicals, Chemicals, Foods, Minerals, Textiles, Agriculture
|
|
AKO – Innovations in Pinch Valves
The valve solution for abrasive, corrosive and fibrous products like granulates, powders and slurries (ISO 9001, CE,...).
Advantages:
• Free passage
• Optimum tightness
• Low resistance
• No plugging
• Low air consumption
• Low weight
• Easy maintenance
|
|
The valve solution for abrasive, corrosive and fibrous products like granulates, powders and slurries.
Valve function :
The manual valve is closing with handwheel.
The pneumatic valve is normally spring closed, air to open.
Advantages :
Free passage, hermetic closing, safety function in the event of loss of energy/air (PA/PA2).
|
|
- Size Range: 15 - 50 mm
- Service Operation: Diversion, Mixing, Blending
- Materials: Stainless Steel, Carbon Steel
- End Connections: Screwed, Buttweld, Socket weld, Sanitary and others
- Service Application: Water, Oil, Steam, Gas, Thermal Fluid, Chemicals and others
- Temperatures: -30°C to 300°C
- Operation: Manual or Actuated
|
|
|
Larox Flowsys Oy is manufacturing reliable and functional pinch valves to process industries worldwide. Larox valves are well suited for shut-off and control applications involving abrasive or corrosive slurries, powders or any other types of materials that can lead to packing and hardening at the valve. Various sleeve, actuator and valve body materials are available to handle a wide range of fluids and materials. The standard range of Larox Valve solutions is for diameters 25 mm - 1000 mm, temperatures -50 C - +160 C, and pressures 0 - 100 bar.
|
|
The new air operated pinch valves- Type VMP Compact
The compact pinch valves were developed for the automatic shutt off and dosing of several bulk and solids, for example: powder, granule, paste, suspensions, pellets and fibrous medium.
Furthermore the VMP-Compact valves get used for the shut off of dust or compressed air.
The air operated pinch valves of the series VMP-Compact are available in seven diameters, (DN010-DN050) with standard internal pipe thread according to DIN ISO 228 or NPT and optional specifications.
A selection of three different materials made in POM (Polyoxymethylen) allows the VMP-compact pinch valves to be used on food (POM nature white) and outdoor (POM black) applications, also available in POM conductive for ex-areas (EX).
Reduced weight, low maintenance, easy to re-sleeve and very cost effective are just a few of the new VMP pinch valve advantages.
|
|
The PRS6 is a three-way pressure reducing valve that has been developed to give reduced pressure in a particular part of the hydraulic system. The valve maintains the secondary pressure setting constantly, regardless of pressure variations on the primary side. Common applications include pilot circuits in hydraulic and electro-hydraulic servo systems.
Compact and easy to install
Easy to adjust within respective pressure range
Can be factory set and sealed to prevent unauthorized pressure changing
Highly suited for use as a reducing valve in pilot circuits where the pilot pressure is taken from the main circuit
|
|
Diaphragm valves, plastic and metal
DN 12 - 100; valve bodies in plastic (PVC-U, ABS, PP, PVDF, PFA, Inliner PP-H Outliner PP reinforced) and DN 4-100 metal (brass, cast iron, S. G. iron, cast steel and stainless steel; lined with hard and soft rubber, PP, PFA, PVDF, Halar etc.); connections to DIN, ISO, ANSI, BS, JIS etc.; manual, pneumatic and motorized operators
|
|
|
|
|
|
Attributes
Maintenance-free diaphragm actuator
For neutral, gaseous and liquid media
Non-sensitive against contaminated media
Control functions:
normally closed (NC)
normally open (NO)
double action (DA) available
Compact design
Sizes DN 15 – 200
Full bore design (without wire)
Different valve body materials
Different lining as protection against corrosion possible (PTFE, Butyl, EPDM, hard rubber)
Threads and flanges
Diaphragm materials: EPDM, NBR, Hypalon, Butyl, natural rubber
Features
For neutral and aggressive liquids and gases
Especially for high viscous and with big particles contaminated media
With the right lining also for abrasive media
The flow can be in either direction
High flow rates
High cleaning quality
Low-end function: only the diaphragm and the body are in contact with the medium
Secure sealing also for contaminated media
Universal application possibilities because of the different material combinations of body and diaphragm
High pressure range, vacuum up to 10 bar (depending on the size)
Easy handling and maintenance
|
|
High Purity diaphragm valves in PFA-HP, PVDF-HP and PP
Cleanroom manufactured High Purity valves for microelectronics, semiconductor production, solar industry and opto-electronic production
DN 6 - 100; valve bodies in ultra-pure plastic materials (PFA-HP, PVDF-HP and natural PP), own cleanroom production in Switzerland, manual, pneumatic and motorized operators, FlareStar PFA-HP fittings, HydraLine pressure measurement devices, TubeStar PFA-HP tubing, SonicLine PFA-HP ultrasonic flowmeter, variable area flowmeters in PVDF-HP
|
|
Features
High cycle double piston stainless steel actuator
Compact design, the outside diameter of the actuator is of the same size as the bonnet flange connecting diaphragm and body
Advantages in multiport bodies and manifold valve assemblies
Control air connection on the top, away from the process product line
Direction of control air connection is mountable in 90° rotations
Circumferential, defined sealing angle between process diaphragm and valve body
Flexible diaphragm suspension
Encapsulated diaphragm
Clean and polished exterior design ideal for sterile wash downs
Optional
Available with a wide range of control equipment and accessories, also for retrofitting
Autoclavable
|
|
|
|
|
|
Whatever you want from a Bulk Materials cut-off valve you’ve got it with Clyde Materials unbeatable Dome Valve® - the cost effective valve solution.
The Clyde Dome Valve®, widely regarded as the original and best material handling valve in the world, offers exceptional life from only a single moving part. The Dome Valve® is recognised as a low maintenance, long life solution that can last at least 1 million cycles between maintenance inspections. It has the ability to cut through static or moving columns of material and is pressure-tight, ensuring a consistent pressure tight seal is created when the valve is in the closed position, but in the open position it provides an unrestricted full bore opening for the best product flow characteristics possible. The Dome Valve® can also be used as a line, vessel or reactor isolation valve.
The Dome Valve® enhances other technologies from Clyde Materials Handling, a leading provider of pneumatic injection, conveying, materials handling & vacuum cleaning solutions.
The solutions we create for our customers generate many benefits and are backed by three decades of domain knowledge, expertise and a track record of generating exemplary success.
Dome Valve® sold in the United States under the trade name ‘Spheri Valve’
|
|
|
Gericke offers a comprehensive range of different diverter valves for pneumatic conveying systems. Starting with simple flat diverter valves, Gericke offers for dense phase conveying systems plug diverter valves and for hygienic applications pipe selector diverter valves type PS. The PS valve is suitable for a wide range of materials and all types of pneumatic conveying systems up to 4 barg. FDA approved materials to meet stringent hygiene requirements. Fast clean version to allow frequent and safe disassembly, gas tight seal which remain inflated even during change along. This valve is suitable for both diverting and converting modes.
|
|
|
|
|
|
Series 240 Control Valves are available in nominal sizes ranging from DN 15 to DN 300 (½" to 12") and up to a nominal pressure PN 40 (Class 300).
Control valves in the standard version are suitable for temperature ranges between -10 and 220 °C (15 and 430 °F). An insulating section allows the temperature range to be extended to -200 and 450 °C (-325 and 840 °F).
The plug stem is sealed either by a self-adjusting PTFE V-ring packing or an adjustable packing. To meet stricter emissions control requirements, a stainless steel bellows is used. The Type 3241 Control Valve can be equipped with a heating jacket that may also include the bellows.
Series 250 Control Valves are used when large nominal sizes and/or high pressures are involved in process engineering, power plant or supply engineering.
In addition to globe, three-way and angle valves, four-flanged valve bodies with bottom plug stem guides, and valves with axial multi-stage throttling plugs, customized valve constructions to meet customer specifications can be engineered as well.
The valves are manufactured in nominal sizes from DN 15 to DN 500 (½" to 16") and for nominal pressures between PN 16 and PN 400 (Class 150 to 2500).
The standard versions of these control valves are suitable for temperatures ranges between -10 and 220 °C (15 and 430 °F). This temperature range can, however, be extended by using an adjustable high-temperature packing to a temperature range between %u201310 and 350 °C (15 and 660 °F) and by using a bellows seal or an insulating section to a temperature range between %u2013200 and 500 °C (%u2013325 and 930 °F).
Series 280 Steam-converting Valves are used to reduce both the steam pressure and steam temperature to optimize plant operation and heat efficiency in process plants, for example, in refineries, food and beverage, tobacco or pulp and paper industries.
Steam-converting valves are based on Series 250 Valves fitted with a flow divider St III and an additional spray water connection. They are available in nominal sizes ranging from DN 50 to DN 400 (1" to 16"), with nominal pressures of PN 16 to PN 400 (Class 150 to 2500) and for temperatures up to 500 °C (930 °F).
The Type DUV-C3 Steam-converting Valve from Welland & Tuxhorn is designed for high-pressure ranges and can be engineered with varying inlet and outlet sizes. The inlet nominal sizes range from DN 80 to DN 500 and the outlet nominal sizes
from DN 100 to DN 1600. Large amounts of spray water can be injected thanks to the integrated atomizing steam cooler. The valve can be operated in a wide load range.
|
|
High Pressure Stop Valve, forged Form with
screwed bonnet and internal stem thread
universal applications.
Typ : AVD, AVI
|
|
|
All series are a non-rotating rising stem design, working pressures to 150,000 psi (1379 bar). Tubing sizes range from 1/4" to 1".Tubing connections utilizes Autoclave's coned and threaded design. Operating temperatures from -423°F to 1200°F (-252°C to 649°C). 316 stainless steel construction, other options available.
|
|
Pneumatic, electric and hydraulic control valves in all common sizes, pressure ratings and materials in accordance with ANSI, DIN and JIS standards.
Optionally, the valves are available with metal bellows and low-noise trims.
|
|
Lined control valves suitable for aggressive media with isostatic lining, valve trim and bellows seal made of PTFE.
As a reasonably priced alternative, the valves are also available with a transfer molded lining of PFA.
|
|
|
|
|
|
Series 240
Pneumatic Control Valve Type 3241-1 DWA, -7 DWA, -9 DWA Globe Valve Type 3241 DWA
Application
Control valve for PSA plants (Pressure Swing Adsorption) (German: DWA)
Valve size ½" to 6"
Pressure rating ANSI Class 125 to 300
Temperatures -20 to 430 °F (-29 to +220 °C)
Industry codes ANSI, ASME and ASTM
Type 3241 Globe Valve with:
Type 3271 Pneumatic Actuator (Type 3241-1 Control Valve)
Type 3277 Pneumatic Actuator (Type 3241-1 Control Valve) for integral positioner attachment
Type 3275 Pneumatic Piston Actuator (Type 3241-9 Control Valve)
Valve body manufactured of:
Stainless carbon steel in acc. with ASTM specification
Forged steel or stainless forged steel
Stainless carbon steel
Undivided valve bonnet
Valve plug: Soft sealing, Lapped-in metal.
Standard version for temperatures ranging from –20 °F to 430 °F (-29 °C to +220 °C)
- Type 3241-1 DWA (Fig. 1) · ½" to 3" with Type 3271 Actuator (see Data Sheet T 8310-1 EN)
- Type 3241-7 DWA (Figs. 2 and 4) · ½" to 3", valve in forged steel up to 3", with Type 3277 Actuator for integral positioner attachment (see Data Sheet T 8310-1 EN)
- Type 3241-9 DWA (Fig. 3) · ½" to 6", with Type 3275 Piston Actuator (see T 8314 EN), for integral positioner attachment and/or limit switch (see Data Sheet T 8310-1 EN)
|
|
|
Control valves for the food processing industry made of polished stainless steel with cavity-free body, PTFE packing or diaphragm seal and connection to a steam or sterile fluid line (optional). The valves comply with FDA and EHEDG regulations and can be sterilized using CIP or SIP.
|
|
|
Larox PVEG is a new pinch valve designed especially for waste treatment plant and other light slurry lines. The body material is polyamide blend, which makes the valve body very light, durable and cost effective. Larox PVEG has standard face to face ANSI B16 dimensions so it can easily be used as replacement to ball, plug and diaphragm valves. Currently Larox PVEG is supplied with handwheel for working pressure up to 10 bar. The available valve sizes are 50mm, 80mm, 100mm and 150mm.
|
|
Eliminating product emissions is one of the most serious challenges for process industry and consequently can be most costly to control.
As part of its Health & Safety initiative campaign Habonim has introduced additional Security to the valve stem design for critical applications.
|
|
|
|
|
|
APV Valves
Over 40 years experience in valve development and production
Valves are essential parts of every processing plant. The APV DELTA valve range has been developed for the process industries, and tailored to the continually increasing requirements for:
* Problem free product flow
* Through flow control
* Safe separation of fluids
* Perfect cleaning
With its comprehensive DELTA valve programme APV offers convincing solutions in those areas where the highest demands on quality and hygiene are made. APV valves offer optimum protection for your products.
* Butterfly
* Single Seat
* Aseptic Single Seat
* Double Seat Mixproof
* Ball
* Aseptic Mixproof
* Safe Flow
* Butterfly Mixproof
* Regulating
* Constant Pressure
* Safety
* Sampling
* Non-Return
* Pressure Relief
* Vacuum
There is over 40 years of experience, research and development invested in our valve range. Complementary to this is the process engineering know-how gathered over 25 years, resulting from installing hundreds of processing plants world wide in brewery, beverage, dairy and food industries, not to mention the pharmaceutical and chemical industries.
APV places particular value on the highest quality of each individual component, thereby ensuring total reliability, a long life cycle and thus satisfaction for the large circle of APV customers.
|
|
Aseptic diaphragm valves, stainless steel
DN 4 – 150; valve bodies in stainless steel (investment cast, forged, block material) and special materials; surface finishes down to 0.25 µm Ra available with or without electropolishing; 2/2-way bodies (2/2-way valve), T-valves (3/2-way valve), tank valve (B600) , GMP-SAP valve configurations, (W600), multi-port valves (M600); connections to ISO, DIN, SMS, ASME BPE, JIS etc.; manual, pneumatic and motorized operators
|
|
LEYBOLD KF valves are available with any of three drive systems and three types of body having a nominal width of DN 16, 25 and
40 KF
Advantages to the User
Isolation component with handy and easy to operate four position rotary knob
Permits careful venting of systems
Suited as a manually operated variable leak valve to roughly control gas flows
Leak tight in both directions up to a pressure of 2.0 etc. 1.5 bar and easy to open
Installation in any orientation
|
|
CPM of valves
Hygenic constant pressure control valves for the installation in high-grade steel line systems.
The valves CPMI-2, CPMO-2 and CPM-I-D60 are hygenic constant pressure control valves for the installation in high-grade steel line systems. CPMI-2 and CPM-I-D60 provide for constant pressure in the piping at the entering the valve. They are suitable for the installation after separators, heat transducers etc. and as overflow valve.
The valve CPMO-2 provides for constant pressure in the piping at the withdrawal from the valve. It is suitable for the installation before filling up/bottle filling machines and the like.
|
|
TECHNICAL DATAS
Ball bearing axle
Inspection cap : galvanised steel
Flap that can be dismantled-high resistance dynamic gasket for Airtightness with permanent pressure
Standard finish : one-coat paint
|
|
Two-way-valves with inlet collar, symmetrical, fitted with pneumatic rotary actuator, 5/2-way-impulse-solenoid-valve (2 coil) and 2 limit switches,
completely wired in limit switch box.
|
|
|
|
