|
|
AKO – Innovations in Pinch Valves
The valve solution for abrasive, corrosive and fibrous products like granulates, powders and slurries (ISO 9001, CE,...).
Advantages:
• Free passage
• Optimum tightness
• Low resistance
• No plugging
• Low air consumption
• Low weight
• Easy maintenance
|
|
The new air operated pinch valves- Type VMP Compact
The compact pinch valves were developed for the automatic shutt off and dosing of several bulk and solids, for example: powder, granule, paste, suspensions, pellets and fibrous medium.
Furthermore the VMP-Compact valves get used for the shut off of dust or compressed air.
The air operated pinch valves of the series VMP-Compact are available in seven diameters, (DN010-DN050) with standard internal pipe thread according to DIN ISO 228 or NPT and optional specifications.
A selection of three different materials made in POM (Polyoxymethylen) allows the VMP-compact pinch valves to be used on food (POM nature white) and outdoor (POM black) applications, also available in POM conductive for ex-areas (EX).
Reduced weight, low maintenance, easy to re-sleeve and very cost effective are just a few of the new VMP pinch valve advantages.
|
|
|
Pneumatic pinch valves provide reliable flow control whenever a source of compressed gas is available. They typically have slower actuation times but higher pinching forces than solenoid valves, making them ideal for industrial dispensing, bulk fluid transfer, and vacuum operations.
|
|
Features
* High cycle life, repeatable control
* Sleeve is the only part in contact with the media
* Eliminates need for expensive body materials
* Versatile choice of sleeve trims
* Able to meet exact flow requirements
* External stroke adjustment
* Bi-directional droptight shutoff
Materials of construction
* Ductile Iron Body
* ATO/ATC, ATO/FC, ATC/FO
* Pneumatic, Diaphragm or hydraulic actuators
* Electric actuators also available,see 5200E
* Flanges ANSI B 16.5 Class 150
* DIN, ASA, or BS standards also available
* Available Elastomers
|
|
|
Gericke offers a comprehensive range of different diverter valves for pneumatic conveying systems. Starting with simple flat diverter valves, Gericke offers for dense phase conveying systems plug diverter valves and for hygienic applications pipe selector diverter valves type PS. The PS valve is suitable for a wide range of materials and all types of pneumatic conveying systems up to 4 barg. FDA approved materials to meet stringent hygiene requirements. Fast clean version to allow frequent and safe disassembly, gas tight seal which remain inflated even during change along. This valve is suitable for both diverting and converting modes.
|
|
90° Diverter
Series 229 & 237
Compact, Abrasion Resistant
The Dynamic Air 90° Diverter is a reliable, low cost, compact and simple design of heavy duty construction. A positive rubber-to-rubber seal is created by the internal flapper which presses against the unused port. The seal improves as the conveying pressure increases, ensuring better performance against leakage in even the most severe dry bulk solids applications.
Features
Abrasion resistant
Positive sealing to 100 PSIG
Full port design
Economical
Compact, low profile
Low maintenance
Position sensors standard
|
|
Fills hoppers via cyclonic separation in the inlet load tube and
exhausting air in the outlet tube.
Valves can be stacked on top of each other allowing multiple sources to multiple hoppers.
Standard Features
- Stainless steel material contact points.
- Lightweight aluminum frame, corrosion resistant.
- Positive blade lock (PBL) between blade and cylinder rod.
- Active compression seals (ACS).
- Internal magnetic piston cushioned air cylinder.
- Stacking design for multiple conveying lines.
- Rated for 82oC (180oF).
|
|
Features:
- Seal rings at each port
- Full round port pass way design
- Heavy duty body design for pressure surges up to 90psi (6.0bar)
- Manual or pneumatic operated
- Heavy duty pneumatic actuator with integrated mechanical stops
Application:
- Suitable for granular and pellets
- For distributing or merging of product flow
- For differential pressure up to 60psi ( 4.0 bar)
|
|
|
|
|
|
The V-Diverter valve is used especially for diverting the bulk material flow in pneumatic dense- and dilutephase conveying systems.
The patented design of the plug enables application in any conveying direction.
Design characteristics
- suitable for pneumatic dense- and dilute-phase conveying systems
- smooth and gap-free transition due to patented design of inlet and outlet
- single channel design avoids plugging
- high dust and pressure tightness due to sealing pressing against the housing
- pressure tight from -1.0 to +6.0 bar (g) gauge to the outside and the non activated leg
- high reliability based on maintenance-free actuator
- solid temperature range from -20 to +120°C and ambient temperature range -20 to +40°C for standard design
- no additional safety device necessary as there are no moving parts outside the valve
- easy installation in all orientations because of integrated cast flanges and supports
- easy subsequent change of complete drive from left to right side of diverter valve
- easily visible direction indicator of plug orientation
- direct control of plug orientation by proximity switches
- all bolts in stainless steel
- low total weight
- defection angle 45°
|
|
Bulk flow has to be distributed an collected. For that diverter valves with the highest demand on functionality and operational safety are used. For product pureness deposit-free and CIP capable diverter valves are indispensable.
Their maintenance-free operation is a deciding factor for the profitability of the plant. Diverter valves from Coperion Waeschle fulfil these numerous requirements even at high pressure and temperature ranges.
|
|
|
Twin-Outlet Diverting Rotary Valve combines the function of a rotary feeder/airlock and diverter valve in one simple mechanism. Select left or right discharge by changing rotor direction via motor and reversing switch. Only one moving part. Very compact. Exclusive tapered rotor allows rotor gap to be easily adjusted. Heavy cast aluminum, iron or stainless steel valve body. Adjustable packing gland shaft seals -- purge available. Heavy duty permanently sealed outboard roller bearings. Ideal for vacuum or pressure conveying systems. Available in five sizes with capacities up to 2,500 cubic feet per hour.
|
|
|
|
|
|
The M-Diverter valve is used especially as a distributor of bulk materials.
The geometric design of the plug enables application in any conveying direction diverting or merging of the material flow from four lines to one or reversible.
Design characteristics
- suitable for pneumatic dense- and dilute-phase conveying systems
- smooth and gap-free transition due to patented design of inlet and outlet
- single channel design avoids plugging
- high dust and pressure tightness due to sealing pressing against the housing
- pressure tight from -1.0 to +6.0 bar (g) gauge to the outside and the non activated leg
- high reliability based on maintenance-free actuator solid temperature range from -20 to +120°C and ambient temperature range -20 to +40°C for standard design
- no additional safety device necessary as there are no moving parts outside the valve
- easy installation in all orientations because of integrated cast flanges and supports
- flanges easy accessible; no special connections required
- easily visible direction indicator of plug orientation
- direct control of plug orientation by proximity switches
- all bolts in stainless steel
- low total weight
- standard design with electrical connections in IP 65
- defection angle 4 x 45°
|
|
Slide Valve (Pictured)
Slide Valve and Lock-Out Slide Valves
In the open position, slide valves allow air to flow through to downstream equipment in the open position. When in closed position, the valve shuts off the air from the compressor. Air trapped on the load side is then bled off into the atmosphere, preventing equipment from unexpectedly cycling even though the line is "shut off".
The lockout slide valves can be locked in the close position. This is an especially important feature when equipment or machinery is being worked on because it avoids accidental start up, which can cause injury to personnel. The lockout slide valve can accomodate standard lock shank sizes up to .145" (sold separately).
Other types of Valves that Coilhose Pneumatics offers:
Ball Valves
Safety Excess Flow Check Valve
|
|
| ... products without technical information |
| |
|
The fine threads of the needle valve permit excellent adjustment for precise control of flow. The flow is restricted in both directions and is adjustable from 0 to the equivalent flow of a 0.025" diameter orifice. The 7-turn adjustment needle valves are available in two models, the standard model and the fine adjustment model. The standard adjustment model has a pin angle of 6° with 10-64 threads; the fine adjustment model has a pin angle of 4° with 10-80 threads.
|
|
Connection guaranteed: a wide range of functions and variants - always harmonised to the respective requirements.
• Exhaust air/supply air flow control or without non-return function
• Flow rate 15 ... 4,300 l/min
• Threaded connectors M3 ... G3/4
• Push-in fittings QS3 ... QS 12 or PK-3 ... PK-6
• Variants with increased corrosion resistance
|
|
LS-V05C
Proportional Pneumatic Control Valve
The LS-V05C is an enhanced version of the LS System proportional, directional control pneumatic valve for high performance applications such as medical equipment, test & measurement systems, advanced automation and animatronics. The valve is designed to be paired with Enfield Technologies driver or controller/driver electronics such as the LS-C10, LS-C41, and C2s.
Features:
* Proportional
* High Speed and Flow
* Whisper Quiet
* Vacuum Capable
* High Linearity
|
|
General Description
Uni-directional
316 Stainless Steel or Brass in-line flow regulators for uni-directional operation (free flow return).
Bi-directional
316 Stainless Steel or Brass in-line flow regulators for bi-directional operation (separate flow control in each direction).
Operating Fluids
- Gases
Filtered lubricated or non-lubricated air, inert gas, sweet (natural) gases.
Sour gas option available
- Liquids
Low pressure hydraulic, mineral oil or water.
|
|
|
Angle Flow Control valves are designed to provide accurate flow control in a compact, labor saving package. Features like built in push-in fittings, pre-applied thread sealant, convenient swivel design and unique needle design all add up to a package that will save time, money and energy when accurate control is needed on pneumatic actuators.
|
|
The miniature Preset Flow Control is ideal for many applications involving pneumatic systems, including the control of cylinder speed.
The operation of the flow control is based on the movement of a small disc. The flat surface on one side of the orificed disc seals and permits flow through the orifice. The amount of flow permitted in the reverse direction is determined by the orifice size. In the forward direction full flow is permitted. The flow controls design allows a maximum supply pressure of 75 PSI with a minimum cracking pressure of less than 10” H2O. Orifice sizes are available from .004” to .040”.
|
|
|
|
|
|
High tech and sturdy air operated valve, with a floating
plug seal, meeting stringent use criteria.
An extra thick body of the actuator and of the valve, ensuring a good resistance to mechanical and thermal distorsions.
A modular design enabling the following configurations:
Shut off valve DCX3 L
DCX3 T
DCX3 X
Divert valve DCX4 L/L
DCX4 T/L
DCX4 L/T
DCX4 L/X
PFA seals quality ensures a complete sealing at high temperature and a good resistance to aggressive products.
Plastomer seal can be replaced by elastomer seal
Single or double acting connection
With plastomer seal, vertical setting up (especially for DCX4)
Dimensions 1” - 1-1/2” - 2” - 2-1/2” - 3” - 4” - 5” - 6” Material
Body: 316L stainless steel
Shut-off unit: 316L stainless steel
Manual or automatic operating devices: 304 stainless steel
Plug seal: PFA and elastomer
Stem seal: viton, EPDM, silicone
Options
• Signal back equipment on the top of the actuator
• Sterilization of the stem through an upper guide bearing
• External = 47 RA max (150 grit)
• Internal = 32 RA max (180 grit)
Upgraded finishes upon request:
Surface Finish
Variants
Plug and body machined for a metal to metal sealing (without seal)
Elastomer sealing (specific plug with viton, EPDM o-ring)
Manual operator device (instead of the actuator
Tank bottom type
Long stroke valve available upon request
|
|
| ... products without technical information |
| |
Model Number PDT-4C1
- Dimensions ( mm）Dia. 44.5×H52
- Type 2way-NC
- Orifice Diameter (mm) 4
- Port Connection Rc1/8
- IN Pressure 0 - 300kPa
- OUT Pressure 0 - 100kPa
- Ambient Temp. Range 0 - 60
- Air Pressure for Action 300 - 600kPa
- Port Connection for air pressure Rc1/8
- Body Material PTFE
- Seal Material PTFE
|
|
|
|
|
|
Product Details
Orifice: 12, 20,25, 40, 50 mm
Pressure: Up to 40 bar
Material: Aluminum, Brass, CF8M
SPECIFICATION
• Body Material: CF8M casting, Powder Coated Aluminium, Brass
• Type: 2 Port, 2 Position
• Operation: Diaphragm Operated Valve
• Orifice: 12, 20, 25, 40, 50 mm
• Operationg Pressure Range:
• Pilot Operated: 0.5 - 10 bar and 1 - 20 bar Direct Acting: 0 - 10 bar
• Temperature of Fluid: -40 oC to 80 oC
• Operating Voltage:
• AC: 24, 110, 220, 240 (50 Hz/ 60 Hz) DC: 6, 12, 24, 48, 72, 110, 220
• Power Consumption: Size 1 coil: 6W, Size 2 coil: 11W
• Application : Drain, Deluge Valve Operation, Dispensing
•Enclosure:
1. General Purpose Flying lead / Plug-in
2. Weather-Proof: Flying lead & Plug in type, Terminal Box as per IS 13947
3. Explosion-Proof with junction box as per IS 2148 group I, IIA, IIB and IIC
4. Explosion-Proof with Junction box as per ATEX, INMETRO, CE and UL (in process) available.
The 2.5" and 3" solenoid valves are special valves and for more details please contact us.
USE 3/2 NO PILOT TO USE THIS VALVE AS NC.
The External Air Pressure should be minimum 2 bar or >_ main fluid pressure whichever is higher.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
