|
|
|
SchuF manufactures specialised Contol Valves for the Chemical, Petrochemical, Oil, Refining, Mining and Power industries. Our control valves range from multistage angle to multiport diverter valves. They include high pressure, high temperture let down valves, boiler, feed and start up valves, disc and piston drain valves with contoured discs and rams, distributor control valves, and bellows sealed valves.
|
|
|
Demand continues to mount for improved comfort conditioning combined with lower operating costs. New architectural designs have created real problems for contractors and engineers to maintain humidity control at reduced loads, and to control load variations. Refrigeration and air conditioning systems are usually designed to provide a given capacity at maximum conditions. These operate with little fluctuation throughout a narrow load range. However, only the larger size machines make any provisions for operation at reduced capacity. In some systems, integral cylinder unloading, the installation of a gas engine drive with variable speed control, or even multiple smaller systems, provide a logical solution.
|
|
LS-V25s
Proportional Pneumatic Control Valve
The LS-V25s is an enhanced version of the LS System proportional, directional control pneumatic valve for high performance applications such as medical equipment, test & measurement systems, advanced automation and animatronics. The valve is designed to be paired with Enfield Technologies driver or controller/driver electronics such as the LS-C10, LS-C41, and C2s.
Features:
* Proportional
* High Speed and Flow
* Whisper Quiet
* Vacuum Capable
* High Linearity
|
|
Pressure valves
As screw-in cartridges or intermediate plate valves
Excellent pressure adjustment over the entire operating range
Pressure relief valves
Unloading valves
Pressure reducing valves
Proportional pressure relief valves
|
|
|
|
|
|
KOFLOC 6600/6800
The KOFLOC Pressure Regulating Valve MODEL 6600 SERIES is a compact, lightweight precision pressure regulator with superior repeatability to provide reliable and speedy regulations. MODEL 6600 SERIES is a non-bleed valve and has successfully been put to rigorous leak tests and is designed as a panel mount unit for easy assimilation into sensitive analytical equipment. Components are carefully cleaned before assembly, making this product ideal for used as a component of high-sensitivity instruments for analysis or other R&D activities. The MODEL 6800 SERIES is a type of check valve to obtain a constant level of pressure upstream of the valve. It makes it easier and speedier to control pressure in the tank with a large buffer, and siphoning, operations that were rather difficult with a secondary control valve commonly in use.
FEATURES
♦ Compact
♦ Low-cost
♦ Quick and easy control
♦ Clean, grease-less valve
♦ Leak-integrity
APPLICATIONS
♦ Tank-pressure control
♦ Gas mixing
♦ Research
♦ Analytical equipment
♦ General gas control
♦ Precision pressure control
|
|
Series PC (Pressure Compensated)
General Description
These valves are designed to regulate flow at a selected rate then maintain this flow constant within ?5% as inlet and outlet pressures may vary. However, changes in fluid temperature will prevent flow from holding constant.
There are 2 types of Series PC valves. Series PCM valves can be adjusted for required flows after being installed. Series PCK valves are factory-set for a specified flow and are not adjustable by the user
|
|
MODELS : VR1E02 (PANEL MOUNTED/SUB-PLATE)
VR4* (SUB-PLATE / THREADED/CARTRDIGE)
VR5* (FLANGE MOUNTED)
VVV01 (SOLENOID VENT VALVE)
SIZES - 1/4 " TO 1-1/2"
FUNCTIONS : REDUCING / RELIEF / SEQUENCE / UNLOADER
FLOWS : 1.7 - 159 gpm / 6.6 - 600 lpm
|
|
SPECIFICATION
PORT SIZE(PT,NPT): 1/4"
ADJ.PRESSURE RANGE(kgf/cm2): 0.5~35
PROOF PRESSURE(kgf/cm2): 40
AMBIENT TEMP: 5-60 C
GAUGE PORT(PT, NPT): 1/8"
|
|
| ... products without technical information |
| |
Crescocito CPR 08A
CRP 08A is a pilot air operated for precise control of paint supply.
Internal designs for optimum performance. Very low usage of cleaning agents/solvents needed per cleaning due to small internal volume and unique design.
All wetted parts made in high grade stainless steel for increased life time.
Large diaphragm diameter for high sensitivity and accuracy.
Dual diaphragms. Teflon diaphragm for fluid function.
Suitable for all types of paint materials, from water based to solvent and UV materials.
Many sizes and types of fittings for fluid connections.
Materials used in CPR 08A:
Housing: Stainless Steel
Cover: Aluminium with surface treatment
Fittings: Stainless Steel
Sealings: Perflour rubber, Teflon
Max working pressure: 8 bar
Size of paint hoses: 4,6,8,9,10,12 mm
Type of fittings: Straight or angled connectors.
Size of pilot air hose: 6/4 mm
Part number: 242 008 000
Approvals: CE, Atex
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
