|
|
|
Gericke offers a comprehensive range of different diverter valves for pneumatic conveying systems. Starting with simple flat diverter valves, Gericke offers for dense phase conveying systems plug diverter valves and for hygienic applications pipe selector diverter valves type PS. The PS valve is suitable for a wide range of materials and all types of pneumatic conveying systems up to 4 barg. FDA approved materials to meet stringent hygiene requirements. Fast clean version to allow frequent and safe disassembly, gas tight seal which remain inflated even during change along. This valve is suitable for both diverting and converting modes.
|
|
Fills hoppers via cyclonic separation in the inlet load tube and
exhausting air in the outlet tube.
Valves can be stacked on top of each other allowing multiple sources to multiple hoppers.
Standard Features
- Stainless steel material contact points.
- Lightweight aluminum frame, corrosion resistant.
- Positive blade lock (PBL) between blade and cylinder rod.
- Active compression seals (ACS).
- Internal magnetic piston cushioned air cylinder.
- Stacking design for multiple conveying lines.
- Rated for 82oC (180oF).
|
|
90° Diverter
Series 229 & 237
Compact, Abrasion Resistant
The Dynamic Air 90° Diverter is a reliable, low cost, compact and simple design of heavy duty construction. A positive rubber-to-rubber seal is created by the internal flapper which presses against the unused port. The seal improves as the conveying pressure increases, ensuring better performance against leakage in even the most severe dry bulk solids applications.
Features
Abrasion resistant
Positive sealing to 100 PSIG
Full port design
Economical
Compact, low profile
Low maintenance
Position sensors standard
|
|
Features:
- Seal rings at each port
- Full round port pass way design
- Heavy duty body design for pressure surges up to 90psi (6.0bar)
- Manual or pneumatic operated
- Heavy duty pneumatic actuator with integrated mechanical stops
Application:
- Suitable for granular and pellets
- For distributing or merging of product flow
- For differential pressure up to 60psi ( 4.0 bar)
|
|
|
|
|
|
The V-Diverter valve is used especially for diverting the bulk material flow in pneumatic dense- and dilutephase conveying systems.
The patented design of the plug enables application in any conveying direction.
Design characteristics
- suitable for pneumatic dense- and dilute-phase conveying systems
- smooth and gap-free transition due to patented design of inlet and outlet
- single channel design avoids plugging
- high dust and pressure tightness due to sealing pressing against the housing
- pressure tight from -1.0 to +6.0 bar (g) gauge to the outside and the non activated leg
- high reliability based on maintenance-free actuator
- solid temperature range from -20 to +120°C and ambient temperature range -20 to +40°C for standard design
- no additional safety device necessary as there are no moving parts outside the valve
- easy installation in all orientations because of integrated cast flanges and supports
- easy subsequent change of complete drive from left to right side of diverter valve
- easily visible direction indicator of plug orientation
- direct control of plug orientation by proximity switches
- all bolts in stainless steel
- low total weight
- defection angle 45°
|
|
Bulk flow has to be distributed an collected. For that diverter valves with the highest demand on functionality and operational safety are used. For product pureness deposit-free and CIP capable diverter valves are indispensable.
Their maintenance-free operation is a deciding factor for the profitability of the plant. Diverter valves from Coperion Waeschle fulfil these numerous requirements even at high pressure and temperature ranges.
|
|
|
Twin-Outlet Diverting Rotary Valve combines the function of a rotary feeder/airlock and diverter valve in one simple mechanism. Select left or right discharge by changing rotor direction via motor and reversing switch. Only one moving part. Very compact. Exclusive tapered rotor allows rotor gap to be easily adjusted. Heavy cast aluminum, iron or stainless steel valve body. Adjustable packing gland shaft seals -- purge available. Heavy duty permanently sealed outboard roller bearings. Ideal for vacuum or pressure conveying systems. Available in five sizes with capacities up to 2,500 cubic feet per hour.
|
|
|
|
|
|
The M-Diverter valve is used especially as a distributor of bulk materials.
The geometric design of the plug enables application in any conveying direction diverting or merging of the material flow from four lines to one or reversible.
Design characteristics
- suitable for pneumatic dense- and dilute-phase conveying systems
- smooth and gap-free transition due to patented design of inlet and outlet
- single channel design avoids plugging
- high dust and pressure tightness due to sealing pressing against the housing
- pressure tight from -1.0 to +6.0 bar (g) gauge to the outside and the non activated leg
- high reliability based on maintenance-free actuator solid temperature range from -20 to +120°C and ambient temperature range -20 to +40°C for standard design
- no additional safety device necessary as there are no moving parts outside the valve
- easy installation in all orientations because of integrated cast flanges and supports
- flanges easy accessible; no special connections required
- easily visible direction indicator of plug orientation
- direct control of plug orientation by proximity switches
- all bolts in stainless steel
- low total weight
- standard design with electrical connections in IP 65
- defection angle 4 x 45°
|
|
| ... products without technical information |
| |
Tubes and bends in pneumatic conveying lines are suffering more or less abrasion. Gericke elbow type GB resists abrasion and avoids product attrition.
It reduces considerabley degradation of conveyed material and avoids formation of angel hair through its patented deflection chamber.
The compact design reduces cost of pipe support and installation. It is automatically self-purging. Little pressure drop.Free trial units available.
|
|
|
Compression coupling for pneumatic conveying system in gavlanized steel or in stainless steel available in 38.1 mm to 324 mm.
|
|
|
|
|
|
For Connecting Pneumatic Conveying Tube & Pipe
- Easy to install - All sizes stocked
- Galvanized or stainless steel shells available
- Precision cut inner sleeves and gaskets
- Thick 1/8" black neoprene gaskets standard
- White, silicone & Viton® gaskets available
- Thick stiffener bars provide added strength
- Copper anti-static strips included
- Grade 5 full thread bolts won't strip or break
- Requires only 3/4" tools to install
- Replacement gaskets available
- Gasket protectors available upon request
- Lengths - 2 bolt 4", 3 bolt 6", 4 bolt 8", 5 bolt 10"
Neoprene - Our standard black gasket for Lorenz Couplings is perfect for most dry bulk conveying applications. Resists rotting, checking and cracking from exposure to ozone.
Temperature range (-40° to +200° F) (-40° to 100° C).
White Nitrile - Excellent gasket for all types of conveying applications. Especially in the food industry. A high quality FDA approved compound ( -40° to 100° C).
Silicone - For use in higher temperature applications. Silicone is odourless, tasteless, non-toxic and noncorrosive. Available for all Lorenz products (-60° to 450° F) ( -50° to 230° C).
Viton® - Please consult factory for specific details regarding this product.
|
|
Features:
- Compact and easy to install
- 100% self cleaning
- Fits all flange and pipe connections
- Available in cast iron, stainless and aluminum
- Reduces noise level
- Minimized pressure drop
Applications:
- For all high and low density dilute phase systems
- For plastic pellets, other granules and abrasive products
- For retrofitting existing systems
- For replacement of long and short radius elbows - and other pipe bends
|
|
|
|
|
|
Raccordi di giunzione (couplings) per trasporti pneumatici, a gravità o in aspirazione.
raccordo serie "IL" per trasporti sino a 2 bar con guaina esterna in acciaio INOX 304 e bloccaggio viti in Nylon 6, fascia intermedia in acciaio INOX 304 e guarnizione in gomma bianca o nera con fascetta INOX di continuità elettrica.
raccordo serie "SL" per trasporti sono a 6 bar con guaina esterna zincata e bloccaggio viti con piatto zincato 30 x 4 mm, fascia intermedia zincata e guarnizione in gomma bianca o nera con fascetta INOX di continuità elettrica.
raccordo serie "SP zincata" per trasporti sono a 6 bar con guaina esterna zincata e bloccaggio viti con piatto zincato 30 x 8 mm, fascia intermedia zincata e guarnizione in gomma bianca o nera con fascetta INOX di continuità elettrica.
raccordo serie "SP INOX 304" per trasporti sono a 6 bar con guaina esterna in acciaio INOX 304 e bloccaggio viti con piatto zincato 30 x 8 mm, fascia intermedia in acciaio INOX 304 e guarnizione in gomma bianca o nera con fascetta INOX di continuità elettrica.
|
|
Pipes and components made of steel, longitudinally welded. Diameter from 60 up to 800 mm.
Material: mild steel, primed or galvanized and stainless steel (st/st). Wall-thickness from 1 up to 3 mm.
Pressed segments with small radius for bulk good handling and pressed bends (with good flow characteristics) with a radius twice as large as diameter (up to 400 mm) for exhaust air/dust extraction plants.
|
|
Quik-Vent™
Vacuum/Pressure Relief Valve
Series 684
Controls unsafe pressure conditions
The Quik-Vent vacuum / pressure relief valve is an excellent safety device for mounting on storage silos, bins or any other container to relieve excessive or unwanted air pressure that might be generated by a pneumatic conveying system or other process equipment.
Unsafe conditions are easily controlled by the Quik-Vent vacuum/pressure relief valve. Generous ports quickly exhaust air or gases to protect against sudden positive or negative pressure conditions.
Optional sensors are also available to provide an electrical signal to indicate when over or under pressure conditions are present.
|
|
|
|
|
|
Air Conveyors - Ring-Vac™ Pneumatic Conveying System:
Available in standard and threaded versions for regular and high temperature applications.
Air Conveyors - Ring-Vac™ Pneumatic Conveying System has virtually no moving parts, convey's air at high rates and long distances. Utilizing compressed air for a powerful, efficient venturi action along its length in a compact design for high capacity conveying over large distances.
Air Conveyors - Ring-Vac™ Pneumatic Conveying System is available in both coated aluminum or high temperature stainless steel. Simply clamp a standard hose size to each end of the Ring-Vac™ to create this high energy conveying system. No moving parts for maintenance free operation with capacity and flow controlled with a pressure regulator.
Air Conveyors - Ring-Vac™ Pneumatic Conveying System is available in 1" (25mm), 1-1/4" (32mm), 1-1/2" (38mm), 2" (51mm), 2-1/2" (64mm), and 3" (76mm) sizes. Any size beyond that can be prohibitive for most applications due to high compressed air requirements.
In addition, beyond 3", the vacuum ability begins to drop significantly except for highly intermittent applications. For applications beyond 3", a blower system often becomes far more economical except in a rare number of possible applications. However, larger size versions are available if required as well as special sizes.
Coated aluminum and high temperature stainless steel Ring-Vac™ Air Conveyor can convey all types of solids in large volumes over great distances with no moving parts.
- Made of an coated aluminum body with no moving parts. High temperature stainless steel models are available for high temperature and corrosive applications.
- Standard sizes to fit standard hose diameter for easy clamping. Threaded versions connect easily to regular pipe thread: 1" (25mm), 1-1/4" (32mm), 1-1/2" (38mm), 2" (51mm), 2-1/2" (64mm), and 3" (76mm). Special sizes can be manufactured if required.
- Utilizing a pressure regulator will control the flow material.
- Instant ON/OFF with no moving parts, no electricity or explosion hazard.
- Longer life in difficult environments than competitive models.
- Ease of use.
- Simple and easy control of material flow.
- Maintenance free operation.
|
|
ICEsonic S-series Air Amplifier.
For an efficient hi-flo operation.
Compact design and no maintenance required.
Products such as ground spices and flour or wastes from textile and paper, fumes and dust can all be conveyed over considerable distance.
Available: Anodised Aluminium and Stainless Steel, from 5 to 50 mm.
|
|
Parker’s RG01 Nozzle, Venturi, and Hot-Gas Bypass Distributors are used for two-phase refrigerant distribution to coils. These need to be mated to a Parker Fixed Restrictor Assembly, a thermal expansion valve (TXV), or other device for refrigerant metering.
* Various nozzle orifice sizes are available for distributor housings.
* Nozzle-style distributor-housings are available for air-conditioning and heat-pump systems.
* Venturi distributors are available with a wide range of configurations and hole sizes.
|
|
Many different things can be transported here. Any piece of pipe will come alive when a "pipe vacuum ejector" is installed.
Compressed air is blown through an annular gap and off it goes. You now can transport items from one place to another at an incredible speed - with low air consumption. One could get the idea to replace a robot with it and use the PVF as a handling unit.
The PVF has a solid outside, no movable parts, meaning a good application range for heavy duty tasks.
Simply an ingenious solution. Try it out and let your phantasy go wild. We will be happy to hear about each new solution you discover - because it is so simple!
|
|
Transportation fan, directfloated, circulating or being certain cover disk.
Sizes:
VRT 400 - VRT 1,250 (D mm)
Employment:
To the promotion of dust, soot, splinter and fiber parts, to 90°C
Technical data:
V = to 15 m ³ /s
Delta pt = to 6,000 Pa
P = to 75kW
Optionally with Keilriemenantrieb
|
|
|
|
|
|
FD range, air conveying blower
-Blower housings made of abrasion resistant cast iron
-hinged housing cover lid for inspection and cleaning
-welded sheet steel impellers with radial blades
-Maintenance-free squirrel cage rotor motors to IP54
The units can only be supplied in the housing position pictured.
Accessories: Various connectors for both inlet and outlet side.
RD F range
The RD F range can be used for conveying of light and non-abrasive bulk.
The blower parts are made of aluminium cast, the impellers are made of welded sheet steel. The solid construction of the practically maintenance
free medium pressure blowers is the basis for a long lasting service life and low operation cost. Inspection and cleaning may only be carried out at these blowers by unscrewing the housing cover plate. All drive motors are made to IP 54 enclosure, class F thermal insulation and comply with EN 60034-1 (VDE 530 Part 1). The motor power is oversized in order to have sufficient reserve for the conveying.
|
|
... see all the products in the category
Blowers
|
|
GF PRIMUS metal separation systems remove magnetic and non-magnetic metal particles (steel, stainless steel, aluminium etc) from pneumatically conveyed bulk materials such as granulates and reground material. Metal contaminants (and inclusions) are removed by means of a reject flap (‘Quick Flap System’) without any interruption to the material flow, even at high flow rates.. Contaminated material is rejected into a container. The reject container is emptied automatically. The GF PRIMUS metal separation system is primarily used in industries where hygiene standards are less important. It is used for inspecting dry bulk materials.
|
|
Magnetic separator for conveying lines.
The PneuMag is a high intensity magnetic separator designed to remove ferrous and stainless steel scrapings from pneumatic conveying lines operating at up to 25m/s.
It features a centrally positioned high intensity magnetic grid with quick release toggle clamps, tamper proof cover plate and totally stainless steel construction.
The PneuMag is particularly suited to flour, sugar and other powder and granulate processing.
High magnetic performance - 9000 Gauss
Reduces 'spark' risk
316 grade stainless steel construction
Cleaned in under 30 seconds
Tamper proof guard
Silicon rubber, metal detectable seal
|
|
|
Series GSP: angular, parallel grip and 180°. Element of the range Easy-2-Combines. High degree of accuracy of repetitivity and long lifespan by a reliable and robust design. Great density power density/dimension.
|
|
Inflatable finger
Parts gripping with no mark
Male: hollow product
- Ø 8.5 to 105 mm
Female: cylinder-shaped product
- Ø 5 to 45 mm
|
|
Series GSP: angular, parallel grip and 180°.
Element of the range Easy-2-Combines.
High degree of accuracy of repetitivity and long life of life by a reliable and robust design.
Voluminal great power/dimension.
|
|
|
|
see the results for the following category : 
