|
|
These high performance ovens offer industry leading production ratings and consistent high quality carbon fiber. Despatch Industries patented center to ends design yields tight temperature uniformity where you need it. Customized solutions optimize cost of ownership, power consumption and safety.
-Design forces air to move completely parallel to the flow of the fibers
-This design allows carbon fiber ovens to operate at consistently higher
temperatures without reaching uncontrolled exotherm
-The result of this technology is that manufacturers achieve 20% higher yields
with uniform density
|
|
IL-RTS Rapid Thermal Shock
Building off of our successful Rapid Thermal Shock product line, Despatch is now offering a new In-line Rapid Thermal Shock (IL-RTS) tool for solar cell manufacturers. This revolutionary tool features a simple, in-line process that applies a low temperature thermal spike to solar cells, eliminating the need for low-bow paste.
After moving through the firing furnace, wafers enter the IL-RTS and are rapidly cooled to stabilize any thermal stresses.
Following the cooling, wafers are warmed to above the dew point temperature to prevent condensation. The IL-RTS is
designed to be compatible with any firing furnace on the front end, and the exit table accepts cell tester automation equipment for a completely seamless in-line process.
|
|
Batch Drying curing Oven
Industrial tailor-made ovens from 1m³ to 200m³ designed to meet your process needs of insulation, temperature and power.
With a temperature range of 20°C up to 500°C these industrial ovens are suitable for all applications of preheating, drying, cooking, polymerization, curing, tempering, stabilization, cooling.
Very robust mechanically welded construction with continuous weld water-tight laboratory, meets all requirements for working in a solvent environment. The rate of air renewal is considered on a case by case basis to allow optimal evacuation of clearing solvent while meeting explosive standards.
Any type of heating following the available energy.
With or without gas exchanger, electric, battery-steam-water oil
|
|
Infrared Microwave Ovens
We provide you with cutting edge radiant technology for drying solutions in record time.
Because your applications are unique, the experts of ELMETHERM offer you a wide range of drying processes such as infrared drying, microwave drying or high frequency drying, offering the best choice for productivity, energy saving and drying time
|
|
Infrared oven VTIR 65/40-200°C
Industry:
Electronics industry
Application:
Burn in of coatings
Special features:
- working chamber: clean room DIN ISO 5
- installation in clean room class DIN ISO 6
- very fast heating up times
- controllable temperature of the products
- fully automated process
|
|
PTC - Long Narrow Load
The PTC ovens offer high performance in a configuration well-suited for heating long and narrow loads such as tubing and extrusions. The forced-air convected ovens feature horizontal airflow with adjustable louvers to assure uniform airflow even with varying load conditions.
A space-conscious footprint is combined with removable end caps to allow placement of several ovens end- to-end. The marinite end caps may also be machined to insert instruments or tooling. Digital, three-mode PID control allows precise temperature control while a separate high limit control with manual reset provides over-temperature protection.
Designed with silicone door seals and positive-latching clamps to hold the door securely in place, the PTC ovens come equipped with a dolly for easy moving.
Application: burn-in and qualification testing of down-hole electronic logging equipment for the petroleum industry.
|
|
Advantages of the in-line concept :
in-line-production from die- to wire-bonding
curing-time < 20 seconds
no warpage of substrates
no batch process necessary
no heat resistant magazines necessary
short quality control cycle
substrate temperature < 90° C possible
|
|
|
|
|
|
The PCO2-14™ Polyimide Cure solution is a clean process oven designed for polyimide baking and curing applications. Many semiconductor manufacturing environments, front-end machines are adapted for polyimide curing. This costly process results in equipment typically not suitable for polyimide curing in terms of cleanliness, inert atmosphere capabilities, cycle time or data acquisition.
The PCO2-14™ optimizes the polyimide cure process for semiconductor wafer devices. It enables short cycle times and a consistent, reproducible cure process for all wafers in the product load by combining four essential characteristics in a single, compact design: clean process operation (Class 100 recirculated airflow), inert atmosphere capabilities (<20 ppm of oxygen), temperatures up to 350°C, and fast cycle times with +/- 1% temperature uniformity.
Like other Despatch thermal processing tools, the PCO2-14™ Polyimide Cure can be networked and controlled from a central location, minimizing the floor space required and further improving productivity. Atmosphere data can also be monitored and recorded throughout the cycle.
|
|
Continuous tunnel Oven for curing drying
The very capable research department of ELMETHERM has developed a wide variety of continuous process tunnels. Since each product requires a specific process, we offer a wide range of solutions for conveying, regulation and aerodynamics.
We work together to conceive the best computer-integrated material handling system to respond to your specific needs and involve all your thermal processing applications.
• Conveyor Belt (PTFE tape, metal, stainless steel mesh)
• Conveyor Chain (work, accumulation, specific supports)
• Continuous Belt (round, flat)
• Motorized roller conveyors, transfer by pilgrim-step system, push girder.
|
|
Curing Towers, vertical curing ovens
We provide turnkey equipment for small spaces for your thermal applications from 40°C up to 350°C.
These tailor-made solutions will help you minimize floor space while providing excellent temperature uniformity, proven mechanics, low maintenance and easy access
TOWER OF STACKABLE TRAYS
This type of tower is extremely compact. By stacking trays it is possible to work at high temperatures without risk of blockages thanks to a simplified mechanization without using chains and possible risk of lengthening. All mechanical components are located outside the hot zone.
We offer facilities tailored to your product.
Loading and unloading at the same or different positions by robot, manipulator, conveyors or manual.
Heating by gas burner or electric resistance.
Possibility of having several temperature regulation zones in the same tower.
Integrated cooling in the tower
|
|
Conveyor Oven
We are experts in thermal process applications and Epcon is ready to design and assemble your custom Conveyor Oven. Our experienced engineers will ensure that your Conveyor Oven accommodates your needs.
Epcon's innovative and patented Industrial Oven designs are built to your unique specifications. Our superior workmanship is evident in all of our custom batch ovens, powder coating ovens, drying ovens, curing ovens.
|
|
Economical electric oven SNOL 2160/220 is designed for various materials and components heat treatment under low temperature, e.g. drying, preheating and other purposes.
•Circulation fan.
•Mild steel working chamber.
•Control block separated from the oven.
•Micro processor temperature controller.
•Moving bottom cart for loading up to 4 t.
•For smaller components special shelves can be placed on the moving cart.
•Two ventilation holes on the upper part.
•Vertical flow hot air circulation.
•Powder painted exterior.
•High quality thermoinsulation materials.
•Low power consumption.
•One year limited warranty and later service.
•Two years limited warranty for temperature controller and later service.
|
|
Explosion-proof safety vacuum drying oven for EX-Zone 2
BINDER VDL EX-Zone 2 series:
Same quality as the VDL series, but with some added safety features: The VDL series EX-Zone 2 is designed for operation in explosion hazard areas EX-Zone 2, in full compliance with ATEX requirements. Our special safety package eliminates any risk.
Find out more: www.vacuum-drying.com
|
|
Applications: cooking, degassing, burning, polymerization, pre-heating, recovery, drying, stabilization, sterilization, vulcaniztion, tests,...
2 temperatures: 200°C maxi or 300°C maxi (depending on the option).
Eight sizes: from 125 litres to 2520 liters.
Several options and accessories to adapt the oven to your needs.
|
|
|
|
|
|
New line of electric ovens are designed for thermal treatment such as drying, heating, thermal testing in an air-flow environment.
Forced convection makes more effective drying and quicker heating, homogeneity of temperature. Good technical parameters ensure to high-quality results. This line allows choices of oven chamber from mild steel LFP or stainless steel (LFN). Available is 5 sizes at temperature ranges up to 300 ºC.
• Micro processor temperature controller with autotuning function
• Double over heat protection system
• Digital setting of temperature
• SSR relay
• High quality thermoinsulation material
• Chamber made of mild steel or stainless steel
• 3 shelves
• Horizontal air flow
• Air outlet control by valves operated manually
• Regulation of fan speed (0-100%)
• Acoustical signalization
• Short heating time
• Heating is from four sides
• Hermetic closing door
• Low power consumption
• High precision level
• Interface RS 232 and software for E5CK 2008
• Interface RS 485 and software for TCViews
• Limited warranty up to two years and later service
|
|
|
|
|
|
Electronic Drying Chamber
OPTIMUM DESIGN
Utilizing a performance enhanced, low-temperature, high volume, updraft re-circulating hot air design, the Omegasonics Optimum 6500 is the ideal machine for drying all types of electronic components after wet cleaning. Whether drying small electrical and electronic content after restoring in our line of Ultrasonic Restoration Pro System Units or our E Series line of Electronic Cleaning Stations, the Optimum 6500 is the perfect fit.
With three (3) adjustable shelves, handling large items or a variety of small electronic components is a snap. There is no prolonged waiting time either for the internal air to get up to the desired temperature. With the 6500, optimum air temperature of 120°F is achieved in less than 60 minutes from a 70°F ambient.
Unique Features:
Updraft Re-circulating Hot Air Design
3450 Watts finned heating element
Heat circuit over-temperature protection
Dual blower design 990 cfm
User friendly illuminated control panel
Digital temperature controller fully adjustable
Digital timer controlled process time
Electrical: 1 phase, 240 volts, 20 amp
|
|
Temperature test chambers with forced convection and individual programming
BINDER M series:
Because of its individual programming options and ability to operate at maximum temperatures up to 300 °C, the M series is ideally suited for materials testing and aging tests. The heavy-duty air turbine and a programmable exhaust ventilation flap provide rapid heating-up and ensure that the test temperature is maintained absolutely precise at all levels, with minimal spatial fluctuations; performance as never before.
|
|
Drying ovens with natural convection
BINDER ED series:
Routine drying and sterilization applications up to 300° C and storage at precisely controlled elevated temperatures are the strengths of ED drying ovens. Because of the natural air circulation with a high rate of air exchange, thermal processes run with significantly increased efficiency.
|
|
Maximum operating temperatures of 400°C, 500°C & 600°C
Chamber capacities of 30, 60 & 120 litres
Good temperature uniformity
Fast heat up and recovery times
Polished stainless steel interior
Stainless steel shelves with multi position settings
Choice of controllers & programmers
|
|
- Applications: drying, heating, hot preservation, hot sterilization (Poupinel), ageing of components, thermal tests in laboratories and industries.
- 2 temperatures: 200°C maximum or 300°C maximum (depending on the option).
- Nine sizes: from 18 litres to 980 liters.
Several options and accessories to adapt the oven to your needs.
|
|
Vacuum drying oven for non-flammable solvents
BINDER VD series:
The VD series offers safe drying with homogenous temperature distribution, thanks to its APT.line™ air jacket system. Optimum heat transfer through patented expansion rack technology; the racks can be positioned as needed and are easy to clean. In addition to these many features, the units have an individually programmable controller.
Find out more: www.vacuum-drying.com
|
|
- Applications: moderate drying of sensitive products, heat treatments of materials being likely to oxidize, fast drying of powders and granules.
- 2 temperatures: 200°C maxi or 300°C maxi (depending on the option).
- Fours sizes: from 20 litres to 240 liters.
Several options and accessories to adapt the oven to your needs.
|
|
Batch Drying curing Oven
Industrial tailor-made ovens from 1m³ to 200m³ designed to meet your process needs of insulation, temperature and power.
With a temperature range of 20°C up to 500°C these industrial ovens are suitable for all applications of preheating, drying, cooking, polymerization, curing, tempering, stabilization, cooling.
|
|
Explosion-proof heating oven
and drying oven VFT 60/90
The VFT 60/90 is an ex-proof fresh air heating and drying oven. The oven is electrically heated and designed according to the fresh-air-principle. Due to the small floor space required it is also suitable for installation in laboratories and in production departments. The advantages, e.g. no restriction on the volume of combustible solvents, suitable for solvents with the temperature classes T1, T2, T3, T4 in the explosion groups IIA and IIB, precise temperature uniformity in the whole working chamber.
Working chamber volume 300 liters
Temperature 200 °C
Temperature classes T1, T2, T3, T4
Installation Zone 2
|
|
|
The Despatch LBB oven features a combination of horizontal and vertical airflow that offers excellent temperature uniformity at a moderate price. It is recommended for a variety of laboratory and production applications including drying, curing, annealing and materials testing.Every LBB oven is UL and C-UL listed, and receives a thorough performance test before shipping.
|
|
Heating ovens and drying ovens for
laboratory and production department, series VTU
These heating and drying ovens are available in 7 sizes with a comprehensive range of accessories, e.g. loading trolleys, temperature controller etc. They can be used globally for heating and drying processes in the production and research.
Working chamber volume 200 – 8.000 liters
Temperature range 250 °C, 300 °C and 350 °C
Air flow horizontal
Heating ovens and drying ovens for solvent-based
materials as per EN 1539, series VTL
These heating and drying ovens are available in 7 sizes with a comprehensive range of accessories, e.g. loading trolleys, temperature controller etc. They can be used globally for heating and drying processes in the production and research.
Working chamber volume 200 – 8.000 liters
Temperature range 250 °C, 300 °C and 350 °C
Air flow horizontal
|
|
|
The LBB pass through features a combination of horizontal and vertical airflow that offers excellent temperature uniformity at a moderate price. It is recommended for a variety of laboratory and production applications including drying and curing.The LBB is designed and manufactured to provide years of dependable service. Corrosion-resistant stainless steel interior and nickel plated shelves clean up easily. The motor is permanently lubricated and virtually maintenance free. And Despatch warrants the heater performance for a full five years - the best warranty in the industry. Every LBB oven is UL and C-UL listed, and receives a thorough performance test before shipping.
|
|
|
|
|
|
Fan-assisted digital electronic sterilizers.
Forced air convection operation
Working range: from +°C above ambient T to +00°C
MAXIMUM TEMPERATURE +300°C
T stability: <±1°C compared to all set point values.
This sterilizer is recommended for all laboratories dealing with devices and products sterilized with hot air: hospitals, analysis laboratories, food and pharmaceutical industries, research centres, etc.
Internal chamber and shelves in glossy AISI 0 stainless steel, external cabinet in brushed AISI 0 stainless steel sheet. Therefore, high mechanical characteristics, good resistance to corrosion and extremely easy cleaning. Each appliance is equipped with racks to position AISI 0 perforated stainless steel shelves (therefore height-adjustable). Internal architecture suitable for creation of a controlled air flow, by means of centrifugal blower: this ensures an optimum internal T distribution inside the chamber and therefore an optimum temperature uniformity, as well as accelerating drying operations. Door equipped with closure with lock and key. Sealing in silicone rubber, for high temperatures, long lasting and easy to clean and replace. W07AC and W08AC models have wheels (front wheels with brake) equipped standard. Insulation with special reinforced mineral fibre panels for high temperatures. Asbestos free. The efficiency of the thermal insulation ensures low temperatures on the outer surfaces and low energy consumption.
|
|
Our U Universal ovens are so varied that almost every customer application can be covered by them. Choose from: 8 model sizes (14l to 749l); 3 performance classes Basic/Excellent/Perfect; Natural convection or forced air circulation N/F.
In accordance with the Law on Medical Products (Directive 93/42/EEC), the UFE / UFP appliances can be used to warm up non-sterile cloths and covers.
|
|
With short heating up times, high precision temperature control and turbo drying, the VO vacuum ovens show off all their power - at the same time they treat heat- and oxygen-sensitive substances and materials with incomparable care. The direct contact between the load and the heatable and removable thermoshelves ensures rapid and equal heating up without thermal loss. Your decision criteria: 3 model sizes (29l, 49l and 101l); State-of-the-art control technology based on the P performance class for all models; Anti-splinter, VDE-tested door construction for all models.
Each of the maximum four (model size 29l: maximum three) insertable thermoshelves is equipped with a separate large area heating and its own sensors. The control circuits react precisely to differences in load and humidity. In this way all levels used remain equally at the predefined set temperature.
|
|
... see all the products in the category
Ovens
|
|
|
