|
|
OUTSTANDING FEATURES
· Low cost.
· Outstanding accuracy.
· Provides wide flow ranges.
· Wide variety of process connections
available.*
· Operate over a wide range of
temperatures and pressures.
· Exclusive use of hybrid ceramic ball
bearings provide superior life.
|
|
This multi-range radial flow turbine meter uses a low inertia turbine supported on robust sapphire bearings in a chemically resistant housing. Ten flow ranges, a choice of "plug in" end connection fittings, and two styles of pulse detection system make this meter one of the most flexible available. The unit has individual traceable calibration, and can be considered as simple apparatus when placed in a hazardous area.
The unit can be configured with fittings and electrical connections to suit OEM requirements. Particular advantages include a wide flow range, long bearing life and in-line design. Output is via a pulse, which can be monitored by simple electronic systems.
|
|
Derived from the FSC Series, the F2000 Quad
Series of fl ow sensors utilizes two fl ow transducers
which are 90-degrees electrically out of phase
from each other. With the addition of a second
fl ow transducer, it is possible to monitor fl ow in
both directions. The F2000 Quad is suitable for
up-down counters that can discern the leading
and trailing edges of the quadrature signals.
Current applications include using the F2000 as
a speed-sensing device on mobile equipment.
This bi-directional fl ow sensor can be used as
a governor, sending frequency signals back to
a PLC which enable it to make the necessary
adjustments. Other functions of the fl ow sensor are
in linear applications where accurate positioning
is required.
Quad Series Turbine Flow Sensor
Provides Bi-directional Flow Rate Measurement
Viton
|
|
|
Blancett sanitary turbine flow meters for liquids meet the 3-A standard for C-O-P (clean out of place) and S-O-P (sterilize out of place) procudures. Flow rates to 400 GPM, clamp sizes to 2.5".
|
|
|
Blancett turbine flow meters for liquids are available in pipe sizes from 1/2" to 10" and flow ranges from 0.6-3 to 500-5000 GPM. Blancett turbine meters use high-quality materials of contruction, including 316 stainless steel and tungsten carbide, to ensure high performance in rugged and aggresive environments. Blancett Model 1100 turbine meters offer +/- 1% accuracy and 0.1% repeatability, and they are rated to 350 degrees F (177 degrees C). Uses include secondary oil recovery, semiconductor, food and beverage, and pharmaceutical.
|
|
Turbine flow meters are mediate volume transmitters similar to a Woltmann's sailwheel meter. Thanks to extremely rapid response times and high resolution turbine flow meters are perfectly suitable for fast filling systems.
Due to an enormous pressure and temperature resistance turbine flow meters will also be the perfect choice for water torch systems, temperature control units, cooling circuits or painting systems, where the consumption of solvents and di-water needs to be measured.
|
|
|
Based on the proven design of the HM turbine meter, the HMP Turbine Flowmeter satisfies the specific design and performance requirements of Life Sciences applications. The HMP uses a bushing and shaft combination which makes the HMP suitable for intense sterilization processes and allows for steam blow down.
|
|
Our Proportional Velocity (PV) Meter is a flow meter that will handle problem fluids that damage other meters. While other meters may stop or be damaged by such common elements as sand, grit, stones (up to 0.25" diameter in our smallest meter), or even wood and rubber, Oilgear flow meters are products on which you can rely for unsurpassed performance.
Advantages of the Oilgear PV Meter
* Large Particle Clearance (up to 0.25" diameter in our smallest meter)
* Long Life in Contaminated Liquid
* High Tolerance to Overranging
* Readout Flexibility
* Mechanical Readouts
* Electrical / Electronic Readouts
* Calibration
* Accuracy
* Repeatabilit
|
|
PLASTIC IMPELLER FLOWMETERS FOR CHEMICALS
These flowmeters have a pulse out. Construction is simple. Rangability is good. Cost is low.
SRP and SRT flowmeters
-3/8 to 1 inch
-5-40 GPM max flows
-20-150 LPM max flows
-TFE or Polypro bodies
-Threaded ports
-High resolution rotors optional
-Ruby bearings
-Very high rangability
|
|
Measuring -/switching range 0,08-5 l/min ...40-160 l/min. water
Connection G 1/4...G 1 1/2, flange DN 15..DN 50,
Material brass, st. st., trogamide, polysulfone, PVDF
Max. pressure 6/10/16/100 bar
Max. temperature 80 °C
Accuracy ± 2,5% FS
Relays; option analogue output, counter, batcher,
Digital display
|
|
|
The Litre Meter pelton wheel flowmeter was first patented in 1975 and has an established reputation for function and reliability. Flows from 0.004 l/min can be metered up to 28 l/min using our LM series range. Large flowmeters are provided utilising the orifice/bypass principle where a wide flow range is given and the ability to measure low flows is retained. Pelton Wheel flowmeters are suitable for low viscosity clean fluids with variants in all- PFA Teflon for maximum chemical resistance and high pressure types to 2000 bar at the other end of the spectrum.
|
|
Measuring liquids and liquefied gases in the chemical and petrochemical industrie, in the mineral oil industry, in the food and beverage industry and loading systems, especially for high operating temperatures and low viscosities.
Turbine Meter RQ Series 1
DN 10 - 65
PN 16 - 320
flow rates 0,15 - 120 m³/h
accuracy ± 0,15 % over a reduced flow range ( for viscosities of 0,2 %u2013 0,7 mPas )
accuracy ± 0,25 - 0,3 for the standard - flow range ( for viscosities of 0,2 %u2013 0,7 mPas )
operating temperature according to design -196°C to 250°C
for custody transfer admitted
|
|
LC Turbine Flow Meters
- Sizes: 1/4" through 12"
- Flow Rates: 0.25 - 12,000 GPM
- End Connections: ANSI, NPT (¼ to 2"), Tri Clover, Flare Tube, Wafer
- Pressure Ratings: 150 - 2,500 ANSI
- Materials of Construction: Body: 304,316,316L SS; Rotor: 17-4 pH SS
- Bearing: Metal Ball, Carbide Sleeve, Cryo Ball, Fluorosint Sleeve
- Accuracy: Capable of ±0.25% of rate over 10:1 range
- Repeatability: Capable of 0.05% of reading over entire range
|
|
|
The Blancett QuikSert In-line Turbine Flow Meter provides the high accuracy and rigorous design of the standard Blancett turbine, but in a wafer-style mounting configuration. With a unique "between-the-flange" design, the need for mating flanges is eliminated, saving installation time and cost, and allowing for limited space requirements.
|
|
The CAT3 is a DC or AC powered, microprocessor
controlled transmitter. It outputs a pulse scaled per unit of
flow, and analog signal proportional to flow rate. The
CAT3 can be configured with High and Low alarms.
|
|
|
|
|
|
initial smallest measurable flow rate dependent on type of vane wheel:
in gases 0.2...1.6 m/s; in liquids 0.01...0.1 m/s
terminal flow rate dependent on type of vane wheel:
in gases 3 m/s; 20 m/s; 40 m/s; 80 m/s;120 m/s;
in liquids: 3 m/s; 7.5 m/s; 10 m/s; condition: no cavitation
probe diameter:
16 mm; 25 mm; 25/27 mm and 30 mm
working temperature range:
up to 100° C; 260 °C; 370 °C; 450 °C and 500 °C
maximum working pressure:
up to 10 bar overpressure (higher on demand)
explosion-proof type of protection:
Category 1G, 1D (Zone 0, Zone 20); Category 2G, 2D (Zone 1, Zone 21)
probe tube material:
aluminium, stainless steel, titanium
optional incl. direction indication
optional incl. integr. temperature measurement
special designs on request
====================================================
Compact units for use in Ex-applications:
for gas: Ex II 1/2 G Ex d e [ia] IIC T6 and
for dust: Ex II 1/2 D Ex iaD20/tDA21 IP6x TX
sensor for use in category 1 (Ex-zone 0 rsp. 20)
transducer housing for use in category 2 (Ex-zone 1 rsp. 21)
probe with diameter 25 mm in different lengths between 250 mm and 650 mm
initial smallest measurable flow rate:
in gases 0.3 m/s; in liquids 0.03 m/s
terminal flow rate:
in gases 20 m/s; 40 m/s; 80 m/s; 120 m/s
in liquids: 7,5 m/s; 10 m/s;
condition: no cavitation
working temperature range:
up to 100 °C; 260 °C; 370 °C und 500 °C
|
|
Turbine Flow Sensor - Series TF
0-5 VDC Output, Liquid or Gas
|
|
Hoffer flow control
Controls turbine flowmeters
Of all the various types of flow transducers available to industry today. None are so universally applicable as turbine flowmeters. They continue to be the most common way to measure flow electronically and have the ability to measure available upon request offering detailed, technical information.
|
|
Flow Sensors
THORNTON offers a variety of paddlewheel, vortex shedding, and sanitary turbine flow sensors to meet the needs of most pure water treatment applications. Smart flow sensors convey their precalibrated values to the 770MAX instrument for ease of installation and startup. Pulse flow sensors can be used with the 770MAX or M300 instruments.
|
|
FLOW RANGE (Note 1)
Ranges shown are standard ranges — other ranges are available. Contact Hoffer Flow Controls Applications Group.
BEARING TYPES (Note 2)
—CB Hybrid Ceramic, Self-lubricating shielded ball bearings. Ball bearings must be used on CO2, may be used on H2O and never on H2O/Sand or CS.
—C Hard Carbon Composite sleeve bearings. For use on H2O only.
—T Tungsten Carbide sleeve bearings. Tungsten Carbide must be used on H2O/Sand and CS, may be used on H2O, and never used on CO2.
|
|
| ... products without technical information |
| |
|
|
