|
|
MODEL: ELP I-25
Load Capacity: Kg 2500
Overall Length: mm 1530
Fork Length : mm 1150
Width over Fork: mm 520 / 540
Lowered Height: mm 75
Raised Height: mm 190
Wheel Type(s): Poly (std) / Nylon / Rubber
Weight: Kg 77
OPTIONS: Tandem Rollers
KEY FEATURES:
Heavy duty reinforced frame
3-position control handle
Hand & foot lowering controls
Adjustable push rods
Exit / Entry helper rollers
Articulating Axle
|
|
| ... products without technical information |
| |
| ... products without technical information |
| |
Hypro roller pumps are the number one all-around choice by farmers throughout the world. The rollers (from 4 to 8, depending on the model) revolve inside the pump housing to force the spray solution through the outlet to the nozzle. Roller pumps have a low initial cost and are extremely versatile. They operate efficiently at PTO speeds of 540 and 1000 rpm and have a wide pressure range of up to 300 psi and flow rates of 2 to 74 gpm. Roller pumps are self priming and easily adapt to PTO or gas engine drives. Specific seal, roller and casting materials can be selected for compatibility with certain herbicides, pesticides, fungicides and fertilizers.
|
|
Die cutter is designated for cutting out different patterns from hard foils, cardboard and paper. It can also be used for cutting out die stampings, from foils obtained in the vacuum forming process, by means of band punching dies placed on the plywood. It enables the so-called cardboard bending (making incisions) and perforation used in the production of foil and cardboard packing.
Two types of die cutter shafts are used: either two steel shafts or an upper shaft covered with a special material.
Using the first type of shafts, the material that is to be cut out and a separator made of a special plastic is placed on the punching die, which is a very impractical solution for large sizes of cut-out elements.
Using the second type of shafts punching die with a cut-out material is placed directly between die cutter shafts. This method increases the output of the machine. Die cutter shafts are driven by transmission belt, which enables noiseless and steady work.
We manufacture 6 models with different size of shafts:
WWP06KNA-600mm
WWP08KNA-800mm
WWP12KNA-1200mm
WWP15KNA-1500mm
WWP18KNA-1800mm
WWP25KNA-2500mm
-----------------------------------------------
zgrzewarki, wykrawarki, formierki
hf welders, rf welders, roller die cutters
Stretch ceiling machines, Zemat TG
-----------------------------------------------
|
|
Kaller Roller Cams are used for piercing, trimming, flanging and restriking.
The Roller Cam can be mounted in both vertical and horizontal planes and contain an internal gas spring for slide return.
|
|
|
Laboratory roll mills are machines for testing the quality and processing characteristics of polymer material by means of discontinuous plastification, mixing or kneading. In both, plastics and rubber processing as well as processing of ceramics or special materials, roll mills by Dr. Collin are setting new standards in terms of precision and reliability.
|
|
|
Roller screw jack provide higher performance compared to ball screw jacks. Ideally suited to applications where a high dynamic load, high accuracy, high speed and a long life are required.
|
|
|
Roller screw jack provide higher performance compared to ball screw jacks. Ideally suited to applications where a high dynamic load, high accuracy, high speed and a long life are required.
|
|
More than 1000 standard tampons in more than 4 quality levels and shore hardnesses directly ex stock from TAMPOPRINT AG - the ORIGINAL. For "open" and "hermetic" tampon printing systems as well as "rotary tampon printing automations".
Special forms available at any time by request. Tests and advisory service in our application engineering department. Decades of experience at your disposal.
|
|
|
The Roller Chain Coupling is a safe, compact and powerful flexible coupling, able to handle loads from 0.1 - 11,000 kW. The sprocket teeth are specially shaped and hardened, and torque is evenly apportioned.
|
|
Indirectly actuated valve series with manually and mechanically actuated valves.
- Flow rate: 120 l/min
3/2-way valve
- Normally closed or normally open
4/2-way valve
- Minimal actuating force with pilot control
- Can also be used as 2/2-way valve by plugging the exhaust.
- 4 actuator types: stem, roller lever, idle return roller lever, whisker
Normally closed or normally open by turning the housing top:
VS, RS, LS
Normally closed, actuator attachment at left (number 1 on attachment above number 1 on housing)
VOS, ROS, LOS
Normally open, actuator attachment at right above number 2
This whisker valve with extremely low actuating forces is particularly well suited for units where dissimilar parts or actuating elements without precision positioning need to be sensed, or where the actuating levels are different. The whisker can be approached from any direction perpendicular to the whisker axis, or can be passed.
- Mounting bracket HV-1/8
Scope of delivery: 1 mounting bracket, 2 M5x25 socket head screws per DIN 912, 2 hex nuts and spring washers
Can be repaired with wearing parts kit
|
|
ECOLINE’s products have been designed to fit in applications where quality movement is needed at a low price. The patented design offers a well-protected, smooth slide that is easily and quickly mounted. ECOLINE combines the quality associated with all of ROLLON’s products with the affordability needed in application sectors like industrial protective panels, vehicle slides, and machine tool doors. ECOLINE is the answer to labor intensive, homemade solutions, cheap bent steel slides, or expensive, overdesigned round or profiled shafting.
|
|
* for die weights above 10 tons
* low rolling friction
* hydraulic lifting
* underside can be used to move rolling bolsters
|
|
elero controls offer you a lot of advantages:
More comfort - your sun protection systems are operated easily by the press of a button.
More safety - roller shutters which are controlled by timers protect against thiefs and burglars.
Easy operation - fully automatic control by radio or press of a button.
Low energy consumption - prevent the undesirable drop in room temperature through automated roller shutters.
Low installation effort - easy installation of the control units without dirt and noise.
|
|
|
|
see the results for the following category
