|
|
|
NETGEAR offers a complete line of reliable, affordable networking switches from high-performing wire-speed Layer 3 managed switches to entry-level managed Smart Switches to plug-and-play unmanaged switches for SMB and the Home. All NETGEAR switches are standards based, fully-compatible with existing 10/100/1000 network infrastructure and easy to use and install.
|
|
Since the introduction of its first circuit switch product over 10 years ago, Vitesse has led development of high-speed serial interconnect to create the most diverse offering of robust and reliable products in the industry. With its unsurpassed equalization technology and proven signal integrity [link to Signal Integrity tech section Signal Integrity] experience, Vitesse continues to advance state-of-the-art technology, and enable its customers to commercialize leading-edge products.
Vitesse offers several IC solutions for systems designers to boost signal performance and increase signal timing and eye margins in challenging designs that operate at speeds from 155 Mbps up to 11 Gbps across all forms of lossy transmission media.
Vitesse's backplane products can be seamlessly interfaced with many other Vitesse products to form complete line card solutions.
|
|
|
Analog Devices' X-stream%u2122 family of digital switches includes high speed crosspoint and 2:1 Mux/DeMux switches. Analog Devices crosspoint and 2:1 Mux/DeMux switches are ideal for WDM, enterprise and metro networking systems commonly employed by Internet service providers, data centers, telecom central offices, and storage area networks. These crosspoint switches are also suited for broadcast video applications.
|
|
|
Offering a combination of mux ratios and wide buses with 5V/3V or 3V/2.5V translation, hot-docking/hot-plugging, bus and load isolation and other features ideal for a variety of applications.
|
|
Moschip family of co-processors provides a companion chip to Moschip Network Appliance Processors. This will allow scalability by adding USB, Serial, Parallel and Display functionality all in a combined solution. The PCI-e bus can be used as a high speed communication link between a processor and co-processor for example.
Not only do Moschip Co-processors integrate with Moschip processors, but they can also be used with other 3rd party processors to gain these added feature sets to their existing devices with a minimal design-in cost
|
|
General overview
Zarlink's Timing-over-Packet (ToP) technology enables accurate timing and synchronization to be distributed across asynchronous packet infrastructures, allowing carriers to con#dently support time-critical services over packet networks.
The patent-pending ZL30301/2 ToP family is built on a processing engine and software solution that encodes and transmits a master clock over existing Ethernet, IP and MPLS networks, and recovers the clock at client nodes.
With Zarlink's ToP devices, Carriers can lower operating costs by migrating to a truly converged network supporting time-critical services, including voice, video and data services. In some applications, ToP technology replaces GPS receivers and T1/E1 connections that are traditionally required to ensure accurate synchronization.
|
|
General description
The ZL50016 is an enhanced non-blocking TDM switch with 1024 x 1024 channel switching capacity. The device offers per-stream rate selection and conversion, embedded G.711 (A-Law/u-Law) code conversion and simultaneous all-stream Bit Error Rate (BER) testing. It is designed to deliver performance advantages and cost benefits for low-density applications.
|
|
FEATURES:
110mW (5V Input) High-Side MOSFET Switch.
500mA Continuous Load Current per Channel.
220mA Typical On-State Supply Current.
1mA Typical Off-State Supply Current.
Current-Limit / Short Circuit Protection.
Thermal Shutdown Protection under Overcurrent Condition.
Undervoltage Lockout Ensures that Switch is off at Start Up.
Output can be Forced Higher than Input (Off-State).
Open-Drain Fault Flag.
Slow Turn ON and Fast Turn OFF.
Enable Active-High or Active-Low.
APPLICATIONS:
USB Power Management.
Hot Plug-In Power Supplies.
Battery-Charger Circuit.
|
|
| ... products without technical information |
| |
The Fuserbloc CD's mean that SOCOMEC has a wide range of fuse switches on the market
The Fuserbloc CD's incorporate functions which make them simpler to fit and use.
Application:
Load-break and protection for low voltage installations and equipment
The range consists of:
25A - 32A - 50A – 63A – 100A – 125A – 160A – 250A – 400A – 630A – 800A – 1250A
Original features and advantages:
The Fuserbloc CD's can meet all the requirements of installers and users:
- The same product reference can be operated from the front, from the door or from the side
- The range includes the "Test" function as standard, so that auxiliary circuits can be tested without connecting the power.
- A patented system gives the customer the option of front or rear connection for the equipment.
- Modular design so that 2-pole products can be used in DC installations together with 6, 8, 12 etc. pole equipment so that several loads can be controlled with the same handle
|
|
Fused isolator switches from 32 to 1250 A
Description
For NFC or DIN, BS, UL type fuses
3 or 4-pole
For direct operator, external front-mounted and RH side-mounted operators, external LH side-mounted operator
Robust and compact handles : padlockable using up to 3 padlocks, lockable, with door interlock, black/grey or yellow/red, IP65 or IP55
Auxiliary contacts:
» Two early break and “O” and “I” position signalling auxiliary contacts, configurable and common throughout the range (GS1AM110 and GS1AM101)
» Auxiliary contacts GS1AN suitable for isolation. Reversibility of these contacts to convert a N/C contact to a N/O contact and vice versa
» Off-load control circuit test facility, with auxiliary contacts GS1AM110, GS1AM101 or GS1ANT used in conjunction with handles GS2AHT
» Auxiliary “blown fuse” signalling contacts.
|
|
|
|
|
|
Fuse switch-disconnectors from 32 A to 800 A
Description
Nominal current from 32 to 800 A
Voltage rating up to 690 V (AC) and 750 V (DC
3 and 4 pole version
Test position
Indication by fuse operating mechanism
Positive contact indication
Fuse compartment with IP20 protection by insulating covers as standard
Locking device to prevent access to fuses when the switch is in the "ON" position
Upstream-downstream double insulation
Reversed power supply
Compliance with standards IEC 947-1,-3,-5, EN 60947-1,-3 and -5, IEC 60269-1 to -4, EN 60269-1 to -4, BS 88-1 to -4, DIN 43620, NFEN 60269-1 to -4, NFC 63220
Specificity of the INF family:
Nominal current from 32 to 800 A
Nominal current from 32 to 800 A
Available in 7 sizes
Can be used for all NFC, BS, DIN fuses
Specificity of the ISFT/ISFL family:
Nominal current from 100 to 630 A
3 sizes in ISFT (100, 160, 250-630 A)
2 sizes in ISFL (160, 250-630 A)
Several installation types: mounting plate, DIN rail (ISFT) or on busbar (ISFT/ISFL)
Connection by cables or on busbar
|
|
| ... products without technical information |
| |
|
|
see the results for the following category : 
