|
|
|
NETGEAR offers a complete line of reliable, affordable networking switches from high-performing wire-speed Layer 3 managed switches to entry-level managed Smart Switches to plug-and-play unmanaged switches for SMB and the Home. All NETGEAR switches are standards based, fully-compatible with existing 10/100/1000 network infrastructure and easy to use and install.
|
|
|
Offering a combination of mux ratios and wide buses with 5V/3V or 3V/2.5V translation, hot-docking/hot-plugging, bus and load isolation and other features ideal for a variety of applications.
|
|
Moschip family of co-processors provides a companion chip to Moschip Network Appliance Processors. This will allow scalability by adding USB, Serial, Parallel and Display functionality all in a combined solution. The PCI-e bus can be used as a high speed communication link between a processor and co-processor for example.
Not only do Moschip Co-processors integrate with Moschip processors, but they can also be used with other 3rd party processors to gain these added feature sets to their existing devices with a minimal design-in cost
|
|
General overview
Zarlink's Timing-over-Packet (ToP) technology enables accurate timing and synchronization to be distributed across asynchronous packet infrastructures, allowing carriers to con#dently support time-critical services over packet networks.
The patent-pending ZL30301/2 ToP family is built on a processing engine and software solution that encodes and transmits a master clock over existing Ethernet, IP and MPLS networks, and recovers the clock at client nodes.
With Zarlink's ToP devices, Carriers can lower operating costs by migrating to a truly converged network supporting time-critical services, including voice, video and data services. In some applications, ToP technology replaces GPS receivers and T1/E1 connections that are traditionally required to ensure accurate synchronization.
|
|
FEATURES:
110mW (5V Input) High-Side MOSFET Switch.
500mA Continuous Load Current per Channel.
220mA Typical On-State Supply Current.
1mA Typical Off-State Supply Current.
Current-Limit / Short Circuit Protection.
Thermal Shutdown Protection under Overcurrent Condition.
Undervoltage Lockout Ensures that Switch is off at Start Up.
Output can be Forced Higher than Input (Off-State).
Open-Drain Fault Flag.
Slow Turn ON and Fast Turn OFF.
Enable Active-High or Active-Low.
APPLICATIONS:
USB Power Management.
Hot Plug-In Power Supplies.
Battery-Charger Circuit.
|
|
Since the introduction of its first circuit switch product over 10 years ago, Vitesse has led development of high-speed serial interconnect to create the most diverse offering of robust and reliable products in the industry. With its unsurpassed equalization technology and proven signal integrity [link to Signal Integrity tech section Signal Integrity] experience, Vitesse continues to advance state-of-the-art technology, and enable its customers to commercialize leading-edge products.
Vitesse offers several IC solutions for systems designers to boost signal performance and increase signal timing and eye margins in challenging designs that operate at speeds from 155 Mbps up to 11 Gbps across all forms of lossy transmission media.
Vitesse's backplane products can be seamlessly interfaced with many other Vitesse products to form complete line card solutions.
|
|
|
Analog Devices' X-stream%u2122 family of digital switches includes high speed crosspoint and 2:1 Mux/DeMux switches. Analog Devices crosspoint and 2:1 Mux/DeMux switches are ideal for WDM, enterprise and metro networking systems commonly employed by Internet service providers, data centers, telecom central offices, and storage area networks. These crosspoint switches are also suited for broadcast video applications.
|
|
General description
The ZL50016 is an enhanced non-blocking TDM switch with 1024 x 1024 channel switching capacity. The device offers per-stream rate selection and conversion, embedded G.711 (A-Law/u-Law) code conversion and simultaneous all-stream Bit Error Rate (BER) testing. It is designed to deliver performance advantages and cost benefits for low-density applications.
|
|
| ... products without technical information |
| |
The JetCon 3401G, the industrial Gigabit Ethernet media converter, is equipped with a rugged aluminum alloy case with IP-31 grade ingress protection against
damages of solid objects or dust. With the excellent characteristics of heat dissipation, JetCon 3401G is capable to perform better than ordinary Gigabit Ethernet media converters which are enclosure by steel metal with various of heat dissipation holes.
Unlike those with a single power input, the real time redundant power backup on JetCon 3401G leads to the functionality of a real Industrial Gigabit Ethernet Media Converter with the non-stop transmission.
*Converts 10/100/1000TX to Gigabit Fiber
*Flexible SFP Fiber transceiver design
*Auto Fault Detection and Alarm
*Fault Alert for port and power
*Two way Link loss forwarding
*Power redundancy with wide range input
*IP-31 grade protection with wide range operating temperature
*1.5KV Hi-Pot testing passed
|
|
CM-011-ST (CM-ST100L)
100FX(ST, Multi Mode) to 10/100TX, LLF, LFP
CM-011-SC (CM-SC100L)
100FX(SC, Multi Mode) to 10/100TX, LLF, LFP (Agilent)
CM-011-SC60 (CM-SC100L-SC60)
100FX(SC, Single Mode, 60km) to 10/100TX, LLF, LFP
CM-011-SC30 (CM-SC100L-SC30)
100FX(SC, Single Mode, 30km) to 10/100TX, LLF, LFP
CM-A1000L-GB
LLF + LFP, 10/100/1000 Base-Tx to Mini-GBIC Media Converter
|
|
|
IMC-1021FX are industrial media converters provide media conversion between 10/100BaseT(X) and 100BaseFx. IMC-1021FX series are rigid IP-30 housing design and supporting an operating temperature of -10 to 60?C, and an extended operating temperature (T models) of -40 to 70?C. Therefore, the IMC-1021FX are reliable media converters and can satisfy most demand of operating environment.
|
|
|
|
|
|
|
Our scope of services regarding electronic systems and communication components for fiber optic technology ranges from RS232, RS422 and RS485 to TTY fiber optic converters. Apart from that, our d-light systems offer solutions for the connection of Profibus, Profibus redundant and Modbus-Plus. Our series e-light and DragonLine consist of both managed and unmanaged Industrial Ethernet switches, partly with PoE (Power over Ethernet) functionality. With DragonLine we cover numerous applications concerning Ethernet and Gigabit-Ethernet. The systems of our io-light series transmit switch, control and analogue signals via fiber optics. Furthermore, we offer optical amplifiers and CAN fiber optic converters. Among that, we also offer compact splice boxes and hybrid splice boxes. POF, HCS and multimode or singlemode fiber optics are unsusceptible to electrical and magnetic interferences. Other performance features are the potential separation of transmitter and receiver and ranges of up to 100 km between two fiber optic systems. Apart from SC and ST as optical connection types, E2000 is also available.
|
|
DragonLine 4 Slot Modular Chassis Switch (Managed/Ring)
Features:
- 4 slots for 8 ports 10/100TX, 8 port 100FX and Gigabit uplink module
- Port Based VLAN /802 .1Q VLAN
- Confirms to IEEE802.3u 10BASE-T, 802.3u 100BASE-TX/FX, 802.3ab 1000BASE-T, 802.3z Gigabit fiber
- IEEE802.3x Flow control
- High back-plane bandwidth 8.8Gbps
- I- EEE802.3ad Port trunk with LACP
- Stack management via one IP address, easy management by Web GUI
- Broadcast storm filter
- IGMP support for Multi Media application
- IEEE 802.1p class of service
- Port mirror / Port security
- DHCP client
- Port bandwidth control
- IEEE 802.1d Spanning tree protocol
- Supports GVRP function
- Web/ SNMP / Telnet / CLI management
- Option Module for slot:
- 2 x Gigabit SX module
- Gigabit copper+ Gigabit SX module
- 2 x Gigabit copper module
- 8 ports 10/100TX module
- 8 ports 100FX module
- IEEE 802.1x user authentication
|
|
The series e-light² EL100U2 are 8 port unmanaged Industrial Ethernet layer 2 switches with auto negotiation and auto MDI/MDIX.
The EL-100U2 series contains unmanaged 7/8 port switches for 10/100MBit/s optionally with up to eight RJ45-Ethernet-ports and up to three optical ports which work with POF, HCS, and multimode or singlemode fiber optics. Additional features are auto negotiation, MDX/MDIX and redundant power supply.
The ruggedness to electrical and magnetic interferences, the potential separation of transmitter and receiver as well as ranges up to 40km between two fiber optic systems are important performance features of the transmission with POF, HCS and multimode or singlemode fiber optics. LEDs and potential free contacts of a differential relay signalize defective states.
Apart from ST and SC as optical connection types, E2000 is also available. All systems feature communication with two fibers or a single fiber by BIDI technology with SC connection.
|
|
e-light2M is a 8 port switch that features ring function based on the Pathfinder Ring (P-Ring) with a recovery time of less than 300ms.
e-light2M is available with up to 4 flexibly configurable FX-ports and up to 6TX-ports. The Fast Ethernet switches with their industrial design are useable in a wide temperature range of -30°C to +75°C and are suitable for both DIN rail mounting and wall fastening.
The e-light2M management highlights are amongst others: Web Management GUI, Port Mirroring, DHCP Client, IGMP, SNTP, SMTP, port and tagged based VLAN, SNMP in connection with Web Management and RMON, quality of service as well as an alarm relay output for system events. e-light2M is suitable for POF, HCS, multimode and singlemode and allows ranges of up to 100km.
|
|
KOM300
Industrial Ethernet to Fiber Media Converter
KOM300 is an industrial fiber optic convertor which can work in harsh electromagnetic environment within a wide range of temperature.
- Operating temperature: -40 to 75°C(-40 to 167°F)
- 2×10/100Base-T/TX, RJ45 socket
- 1-core single mode fiber
- Broadcasting storm control
- MAC Address Table Size: 1K, buffer cache: 1M
- IP30 protection class
- DIN-Rail mounting or rack-mounting
- FCC/CE/UL/ROHS
|
|
| ... products without technical information |
| |
The SS-110 Slow Speed Switch is a complete system that has one adjustable set point for monitoring a single rotating shaft.
This Speed Switch is used in slow speed applications, and allows accurate underspeed detection within the 1/100-10 rpm range. The SS-110 System is an efficient way to continuously track proper machine RPM, and provide a relay output upon detection of an unwanted change in speed or stoppage of the monitored shaft.
Features:
- Dial-In Calibration Does Not Require Power
- Set Point Ranges: .01 - 0.99 and 0.1 - 9.9 rpm
- ETL Approved to UL 508 Standard
- Completely Field Adjustable
- Fail-Safe Operation in Underspeed Mode
- DIN Rail or Stand Alone Mounting
- Additional DIN Rail Available - Consult Factory
|
|
|
Speed responsive switches detect motion, or sense over-speed or under-speed occurrences of industrial machinery or motors. Hubbell Industrial Controls, Inc. has both direct coupled or non-contact type switches for; directional, non-directional, plugging, anti-plugging, over-speed, under-speed, and also zero-speed applications. Many enclosure styles are available including surface or flange mounting with NEMA 3, 4, 7, 9, 10 or 13 construction.
|
|
|
|
|
|
The combination of a coder with ends of the road in the same case increases the reliability and the safety of the machines, because of two independent checking circuits in the same case.
The coder integrated provided information uninterrupted of the movement in 5-30 VDC with a resolution from 100 to 5000 increments. The programmable ends of the road, the catch of origin are regulated freely with the position wished.
The adjustment of the ends of the road is very simple: the case is assembled on the machine, the machine is then led manually to its limiting position, the end of the road is positioned with a key of programming. This procedure is repeated for the other end of the road.
The case is well protects by its cap against dust or any external intervention; all the signals are cabled on a connector with the back of the case.
These cases can also be provided with potentiometers.
COMP' AUT will be able to best advise the customer in the choice of the case being appropriate for its application.
|
|
| ... products without technical information |
| |
These PCB series of acceleration or shock sensors are intended for applications where acceleration, velocity or impact need to be sensed. Many commercial applications exist (automotive, motorbikes, test equipment,…)
Their size is very small enabling them to be mounted practically everywhere. High reliability, robustness and no power needed for activation, are their major advantages.
These acceleration and shock switches are available from 1 to 15 g-level .
|
|
ASLS-2
Contact Form/Style: Normally Open
Switching Voltage: 24Vdc Max.
Switching Current: 0.25A Max.
Switching Capacity: 5VA Max.
Activation Level: 2-4.9G
Contact Resistance: 10 Ohms Max.
Size: Over All Length: 0.709in (18.0mm)
Diameter: 0.181in (4.6mm)
Electrode Diameter: 0.020in (0.50mm)
Electrode Spacing: 0.114in (2.92mm)
Acceleration and Shock Switch
|
|
The 20.SS is an electromechanical device designed to protect equipment from damaging shock or vibration. The sensitive mechanism detects excessive shock and shutdown the equipment before further damage occurs.
20SS shockswitches are housed in an ATEX certified enclosure and can be used for applications requiring an execution of EEx-d-IIC-T6.
|
|
|
|
see the results for the following category : 
