|
|
| The MTI-2100 Fotonic Sensor is a high-resoulution fiber optic based vibration/displacement sensor with extremely high frequency response. The system offers a bandwidth up to 500 kHz and resolution to 0.01 microinch (2.5 Angstrom). |
|
The Fiber Optic pH Sensor system consists of a fiber optic probe designed to hold immobilized colorimetric indicator dye materials, plus a light source, spectrometer and OOISensors Software. You can supply your own indicator material, or select from our line of transparent or reflective films. Calibration involves recording spectra in high and low pH samples, and in at least one pH standard such as a NIST-traceable buffer.
|
|
· 4 models: Standard, High Speed, Mark Detection and Moisture Detection.
· Unique "Moisture Sensing Type" BIF-W series senses the presence of moisture in a product.
· High Speed type (50 micro sec) and Green
LED type for Mark Sensing.
|
|
| Cubicle and cylindrical models for the adaption of fibre optics. Fibre optics that meet every application (barriers, proximity switches and cross-section converters) |
|
These electronic devices, photoelectric sensors or photocells, use the light emission principle combined with the electronic and are made up
of an emitter or luminous source, the light rays of which are detected by a receiver. The variation in luminous signal, obtained when interrupting this ray, is converted into an electrical signal and is measured and used by
an electrical circuit. The light used is either infrared or red. By making use of this light various type of photoelectric sensors can be made. The AECO photoelectric sensors available in the FOTOSTAR range are the FT18M - FT18 -FTQ series in direct reflection, with reflector with polarized light and emitter-receiver versions. Due to their flexibility regarding the various
standard programmable versions these products offer the possibility of stocking reduction and are easily interchangeable with most of the units available on the market. They are used in the field of automation to check for the presence, counting, position control, etc., and they
are compatible with most logic programmers. |
|
D10 Series: High-performance fiber optic sensors
- Advanced fiber optic amplifier for use with plastic fibers
- Available with visible red or green sensing beam
- Delivers high-performance, low-contrast sensing
- Automatic TEACH options or manual adjustment
- Available in bipolar discrete, dual-discrete or analog/discrete output models
ExpertTM models
- 4-digit TEACH and signal strentgh display or bargraph readout
- Operating status indicators
- Easy-to-set static, dynamic and single-point programming
- Manual fine tuning
- Remote configuration, using TEACH wire
Plastic & Glass Fibres
- Banner offers an unrivalled selection of standard & customised fibres. |
|
FX-100 - top price-performance ratio powered by technological innovation
New possibilities with digital fibre sensors. SUNX has developed a new top price fibre sensor. The quick set mode allows inexperienced operators to use the sensor quickly. For experienced operators, the setting and PRO mode are still available. Other features, such as the ECO mode, copy and GETA function, enhance its practicality in the workplace. A total product range of 12 types will be available for all customers’ requirements.
Characteristics:
One 4-digit green, one 4-digit red LCD display
Copy settings via wiring as with DP-100
3-step setting hierarchy, from basic to advanced
External input for external adjustment
No need to connect amplifiers in case interference prevention is requested
Direct installation possible without bracket or DIN rail
Commercially available connector simplifies procurement
Key-lock function
Teaching, light-ON / dark-ON setting
Threshold values can automatically adjust to changes in incident light
Intensity of emitted light can be reduced automatically to ensure stable sensing
Accessories:
Various cable lengths: 1, 2, 3, 5m
End plates
Protection cover |
|
Digital Fiber Amplifier with Two Independent Outputs.
High speed 60 micro second response.
APC Function (Auto Power Control):
The APC function ensures precise sensing even when there are changes in the temperature or environmental conditions. |
|
Referenos: AF CLARYS 2, 3, 4
Sensing distance with plastic fibre or glass fibre: see "Plaslic Optical Fibres' or "Glass Optcal Rbres
High resolution up to 5100th mm
2, 3, 4 channels + logical output AND/OR
Modeb: output P, output N
Optional: Analogical output
Smpfe feactvin: 1 or 2 thresholds
Timer OWOFF delay: 0 to 10s
Dimensions: 99x45x325 mm
Resolution 5/100th mm with 2000 points
Applications:
Level controls: high and bw
High precision detection of movement
Presence cdetection, up to 4 units simultaneously
Up to 4 beams barrier
Mark detection |
|
| ... products without technical information |
| |
| The Fischer 1053TM Fiber Optic HDTV Camera Connector meets the Broadcast industry’s requirements for an effortless transition to fiber-based HDTV cameras. Proven reliable in the field, it is fast and easy to terminate. |
|
| ... products without technical information |
| |
The FCR-7xx200-2 is a standard reflection probe to get spectral information of diffuse or directly reflecting or back-scattering materials.
Via a standard SMA905 connector light from a light source is coupled into a fiber bundle, consisting of 6 fibers and carried to the probe end. The surface will selectively reflect light back into a 7th fiber. This fiber transfers the data to the output SMA905 connector, which can be coupled to a spectrometer or spectrum analyzer.
A higher number of fibers are possible to couple more energy from the light source and to increase the signal level.
For measurements under 90º the FCR-90-Option, a special adapter with a mirror under 45º, was developed, which can be easily mounted on the tip of the reflection probe.
The FCR-COL is available to focus the measurement spot on an extended distance.
|
|
| Ocean Optics sensor systems are ushering in a new generation of low-cost, portable chemical-sensing devices. Thanks to innovation in the development of chemical-sensing complexes -- particularly those with fluorescing properties -- products such as our Oxygen Sensor systems will continue to provide viable alternatives to traditional chemical-sensing devices such as electrodes. The use of optical-sensing methods lessens the reliance on the electrochemical technologies that have dominated the field of oxygen sensing. |
|
The EFS 8217 system is designed for temperature measurement in environments where there is electrical disturbance.
This system relies upon an optical measurement principle, yet can be connected simply like a typical electrical sensor by means of a 15-pin Sub-D connector.
Possible applications
Temperature safety on asynchronous electrical motors
Measurements in transformers,
Measurements in electrical racks,
Measurements in EX zones (explosive atmosphere),
Measurements in areas subject to significant electromagnetic disturbance. |
|
| The PRO 50 Single-Wavelength Sensors with Fiber Optics are used to measure most common materials in general purpose applications. With the fiber optic configuration, it is possible to view a target and mount the sensor electronics in a remote or more convenient location. This provides greater durability and flexibility with sensor installations that involve confined spaces and/or severe environments. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
Characteristics:
- Model CRD/H: transmission of the signal and the supply voltage by a liasion by a liaision copper
- Model CRD/W: transmission of the signal by fiber-optics (LWL), supply voltage by a liaision copper.
- Electric Connection: Connector Han-Brid ® with enclosure of connection. |
|
| FiberFly is the ultimate solution for precision marking and micro-processing of all types of metals and plastics. Extremely compact, modular and perfectly sealed, it is configured for easy integration into any industrial production line. The FiberFly system offers the perfect combination of reduced operating costs and high throughput. |
|
FiberStar's OEM, Integration Marking Systems offer the benefits of a Direct Metal Marking, non-contact, abrasion-resistant, permanent laser marking onto almost any type of material. High-speed, high precision, micro-marking FiberStar systems are ideal for a wide range of industries and integration applications.
FiberStar Systems offer state-of-the-art technology with the highest laser beam quality and more than 30,000 hours of maintenance-free operation. High precision markings are achievable on almost any type of material including stainless steel, strength alloys, carbide, copper, titanium, platinum, aluminum, as well as a wide variety of medical-grade alloys and plastics.
Identification text, serial numbers, corporate logos, 2D data matrix, bar coding, graphic and digital images, or any individual process data can be produced with laser marking.
- Logos, certification symbols,barcodes, serial codes, and 2-D data matrix code
- Simple custom text, serial numbers, bitmaps, graphic and CAD-files (HPGL)
- Marking and cutting of foilsand light-gauge steel sheets (ie. labels) in one cycle
- Rapid marking on precious metals with heat-sensitive materials
- Plastic materials: day & night design for items such as mobile phone keyboards, dashboards, and other illumination components for aerospace and automotive markets |
|
Impulsato laser to active fiber optic with powers from 10 and 20 Watt.
This laser answers to the productive necessities more demanding guaranteeing the maximum rapidity of working, and is particularly apt for the labelling of a wide range of metallic and plastic materials and for microworkings and microcuts of precision
The force points:
Head of dislocabile scanning
Elevated efficiency
Highest quality of the bundle laser
Spot of scrttura ridottissimo
Stability in power
Reduced it blocks
Duration of the diode valves:
- Till 30.000 hours
- Maintenance ridottissima: only the cleansing of the disc of a valve |
|
| ... products without technical information |
| |
|
|
see the results for the following category
