|
|
|
This pile was developed based on the ductile pipe that has long been used for water pipelines, and is usually used as a bearing pile for small buildings. The strength is higher than the commonly used structural carbon steel, and the corrosion resistance is more than two times higher. The ducpiles securely support a building, contributing to improving the safety of a house or other small structure.
|
|
|
|
|
|
GALVA-GARD®, "The Ultimate Corrosion Fighter" is a prefabricated, preinsulated, fiberglass clad galvanized steel conduit system for low to high pressure steam, HTHW and general fluid transportation.
GALVA-GARD® the original "corrosion fighter" just got better. As always, galvanization is applied to the exterior, as well as the interior of the outer pipe providing a clean, corrosion resistant system for underground heat distribution. Now PERMA-PIPE® has added a thick cladding of fiberglass reinforced plastic on top of the galvanized system for maximum resistance to adverse corrosion and environmental conditions. There is no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick and designed to withstand a 35,000 volt holiday test. GALVA-GARD® is a smooth wall, hot dipped galvanized, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Energy Loss Detection and Location system and electric heat tracing.
- Temp Range: 250°F to 750°F (standard), above 750°F (special)
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
XTRU-THERM®, our "State of the Art" preinsulated piping system for fluids from cryogenic temperatures up to 250ºF. The extruded HDPE jacket results in a completely bonded system that moves as a single unit for maximum efficiency and service life.
XTRU-THERM® is a process driven product, developed to eliminate problems inherent in foam injected systems. The pipe is insulated using a special spray applied continuos feed insulating process which works in line with our extruded high density polyethylene plastic material. The JACKET remains flexible at low temperatures and has a higher temperature rating than PVC. The HDPE jacket has been specifically designed to bond to the insulation. Designed for both above and underground insulated pipe applications. The hardness, tensile and flexural strength, toughness, diameter and thickness of the jacket are controlled.
The foam insulation is spray-applied and rises, unrestricted, to its final thickness. The free rise allows cell structure of the foam to be uniform in all directions. Because the foam is spray-applied and not injected, XTRU-THERM® is guaranteed to be 100% void-free. The blowing agent (HCFC, a gas that expands the foam and creates cell structure) does not dissipate from the cell like other water-based agents. Therefore, the cell structure and thermal value is maintained and the foam will not shrink.
- Temp Range: -320ºF to 250ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter 1/ 2" - 36" (standard), Nom. Length 20' and 40'
|
|
We are a worldwide market leader for piping systems and components in plastic and complementary materials. The application-oriented system solutions and superior quality components are used for industrial applications, gas and water distribution, and building technology.
PVC-U
PVC-C
ABS
â-PP-H
PP-R
PE 100
PVDF
Pre-Insulated Fittings
Double Containment
Multilayer Fittings
PB
|
|
|
|
|
|
ULTRA-NW™ is an advanced prefabricated, secondary containment piping system for hazardous chemicals, process waste and general fluid transportation. It is a fiberglass clad stainless steel conduit system with no need for cathodic protection.
ULTRA-NW™ is the next generation for complying with Federal regulations for secondary containment of hazardous fluids, this drainable, dryable and testable, prefabricated, secondary contained piping system is designed for the distribution of jet fuel, radioactive waste, Bio-process waste and chemical transfer. ULTRA-NW™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick, and designed to withstand a 35,000 volt holiday test. ULTRA-NW™ is supplied with stainless or other high alloy pipe and containment. Single or multiple steel carrier pipes, can be insulated with any type of pipe insulation, we recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
ULTRA-FS™ is an advanced prefabricated, secondary containment piping system for chemicals, process waste, fuel systems and general fluid transportation is a fiberglass clad steel conduit system with no need for cathodic protection.
ULTRA-FS™ is the next generation for complying with Federal regulations for secondary containment of hazardous fluids, this drainable, dryable and testable, prefabricated, secondary contained piping system is designed for the distribution of hydrocarbons, process waste and chemical transfer. ULTRA-FS™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick, and designed to withstand a 35,000 volt holiday test. ULTRA-FS™ is a smooth wall, minimum 10 gauge steel conduit. Single or multiple steel carrier pipes, can be insulated with any type of pipe insulation. We recommend mineral wool insulation that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system, and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
OLCOMPONENTS is the new product range launched by Olmark, that includes:
- BLOCK PIPE CLAMPS in polypropylene, polyammide or aluminium for single, twin or multiple pipes. Available series: Standard (rubber insert version also available) suitable for pipes with O.D. from 6 to 120 mm; Heavy (rubber insert version also available), suitable for pipes with O.D. from 6 to 168 mm; Twin, suitable for twin pipes with O.D. from 6 to 42 mm. All Olcomponents block pipe clamps can be equipped with cover and base plates, mouting rails and accessories for overlapped clamps.
- STEEL BALL VALVES wuitable for working pressures up to 500 bar, available in the following versions: two or three valves, flanged or MINI. Broad range of handles in zinc, stainless steel or aluminium, and in different shapes: straight, bent, short. Available diameters: from 1/8" to 1"1/4.
- QUICK-RELEASE COUPLINGS for all hydraulic applications at medium, high and very high pressure. Available series: ball valve, poppet valve, flat face and screw-on. Available materials (depending on the series): steel, stainless steel and brass.
All OLCOMPONENTS products meet most important international technical standards of the sector.
|
|
|
The FW pipe, a fiber reinforced plastic pipe consisting of FRP and resin mortar, is used for pipelines carrying agricultural or sewage water. Since FW pipes are strong and have excellent hydraulic characteristics, corrosion resistance, earthquake resistance, and workability, they are widely utilized in both new construction and renovating applications.
|
|
A large range of PTFE lined piping adn fittings that resist to corrosion and answering all your applications :
· PTFE lined elbow
· PTFE lined tee
· PTFE lined reduction flange
· PTFE lined cross
· PTFE lined instrument tee
· PTFE lined piping
· PFA check valves
ND 25 to ND 600.
From 100 to 8000 mm
Up to 230°C
Up to 25 bars
ASME/DIN
PTFE Antistatique (noir)
Heavy duty thickness
Vacuum designed application
|
|
Fluoropolymer Tubing
* Stock PTFE sizes from 4mm to 12mm OD
* Stock FEP sizes from 4mm to 12mm OD
* Suitable for food use
* Non hardening
* Non stick
* Durable
* Excellent chemical resistance
|
|
OLMARK can boast years of experience in designing and manufacturing bended, assembled and flanged rigid pipes (in steel, stainless steel or copper) available in all possible dimensions and shapes required by clients’ technical specifications.
OLMARK’s pipes come, on request, with a CAD-3D drawing and they are all successfully tested in compliance with the most rigid international standardization directives.
With an outside rigid pipe diameter manufacture capacity that can spread from 4 to more than 300 mm, the range of personalised pipes designed by OLMARK is the natural choice of important OEMs, whose success depends on high working pressures control.
|
|
New from Tyco Fire Suppression & Building Products, Grinnell's G-Press(TM) Piping System is a complete piping system for a sprinkler fire protection installation, offering lower system costs, shorter installation times, reduced installation waste/clean up and is approved to international fire standards.
G-Press systems have been developed to meet the growing need for quicker, more precise sprinkler pipe installations together with the expectation of increased safety and security.
The range includes G-Press Fittings (using the G-Press Fitting Connection Method), the G-Press Passive Leak Monitoring (PLM) Sealing Ring and the G-Press Tube.
|
|
Welding accessories for piping in stainless steel
ISO Unions with conical seat, or with PTFE flat seat(BSP or NPT)
3000 Lbs forged unions (NPT) with socket welding (SW)
Coupling SW, half coupling SW, female cap SW, elbow SW, tee SW
ISO, Metric, ANSI standards
90°elbow, 45° elbow, tee with sleeve, tee without sleeve
Concentric reducer, excentric reducer, collar, pipe cap
...
|
|
Stainless steel pipe fittings for dairy and food industries
Béné Inox offers you a complete range of unions and pipes fittings
stainless steel 304L and 316L
for SMS, DIN, Tri-clamp, Macon standars
Butterfly valves (manual or automated), pneumatic seat valves
Check valves, filters, sigth glasses...
Unions for welding, unions for expanding, unions for hose fitting
male part, liner, nut, blind nut, with EPDM/FKM/Viton/PTFE gasket...
SMS/BSP adaptor, DIN/BSP adaptor
Bend at 90°, at 45°, at 180°, tee, reduced tee
Concentric reducer, excentric reducer, pipe cap, collar
Threaded stirrup, clamp, pipe holder, pipe
We also have an "industry" range of fittings (ISO,ANSI standards...) :
Valves, unions, flanges, elbows, tees, réducers...
|
|
Threaded accessories for piping in stainless steel
ISO Unions with conical seat, or with PTFE flat seat(BSP or NPT)
3000 Lbs forged unions (NPT)
Bent unions male/female or female/female (BSP / NPT)
welding nipple, barrel nipple, hexagonal nipple, male plug
female coupling, half coupling, female cap
Bulkhead coupling
Reducer (male/male, male/female, female/female, female/male)
90°elbow, 45° elbow, reduced bend
Threaded tee, reduced tee, cross
...
|
|
|
As the number of large construction projects in areas with weak ground and coastal areas continue to increase, designing and building earthquake-resistant structures has become even more important than before. Accordingly, foundation piles are required to have higher levels of yield strength, workability, and structural reliability. Kubota steel pipe piles meet this requirement. The steel pipe piles have already been used in a number of construction applications such as bridges, ports, rivers, and buildings.
|
|
Round pipes of the company h.hiendl GmbH & CO. Kg
Hiendl of round pipes are made from natural fiber strengthened composite materials of the Hiendl NFC® of material system as well as of purely synthetic thermoplastics (polypropylene, polyethylene, ABS, PVC, PP). The selection of the material is determined in each case by the characteristics, which are optimal for application. The universal products of Hiendl NFC® and of conventional plastics are manufactured for the construction industry, the interior fittings, the laboratory, charge, measurement and the furniture making. With Hiendl NFC® the fossil raw materials common with plastics are replaced to substantial portions by regenerating raw materials. This reduces the load of the atmosphere by CO2-Emissionen. In the comparison e.g. to aluminum - also this material can be replaced by Hiendl NFC® - consumption at primary energy is considerably smaller in the production and processing.
|
|
Mass production, all products of the same quality, subsequent components identical.
Extraction of harmful substances like dust, steam and solvents
Our pull-ring system with U-shaped seals can be used in almost every line of business because it is tight against condensed liquids.
Certificates "shock explosion proof up to 3 bar overpressure"are available on request (angle flange connection is shock explosion proof up to 10 bar).
|
|
|
|
|
|
The Exel pull-winding, co-winding and prepreg wrapping techniques enables the manufacture of high-performance composite tubes while optimizing the structure and minimizing the use of raw material. The wide range of Exel tubes from 3mm to 300mm diameter, together with suitable wall thickness, different types of reinforcement and resins allow you to have an optimized product according to your needs.
The choice of reinforcing materials is determined by the technical demands, such as weight, stiffness and strength, and its ability to insulate heat and electricity. Glass fibre is a widely used reinforcing material that gives the product the following properties: light weight, durability, stiffness and is readily pigmented. Carbon fibre enables the manufacture of even lighter and stiffer tube. It should be noted that carbon fibre conducts electricity. Although carbon fibre tubes are black, they can be coloured by introducing a glass fibre surface layer. A hybrid is a product that combines more than one material. It is thus possible to optimize lightness, stiffness, strength and costs.
Tubes usually have a non-wowen surface, and the surface resin is pigmented throughout. The pigment can be selected from numerous standard colours, for instance, according to the RAL or PANTONE colour codes. If requested, the colour can be made to the customer’s requirements. Tubes may also be given a spiral surface. The customer’s name or some other information may be printed on the tube surface.
Exel quality and environment policy complies with the requirements of the standards ISO 9001:2000 and ISO 14001 (Bureau Veritas Certification).
|
|
Fire Protection Sleeves
Designed to avoid the expenses of fireproof ducting, the sleeves are efficient and cost effective.
Two semi-circular metal shells are lined with intumescent material that when heated expands making a fire barrier.
|
|
Pressed segments with small radius for bulk good handling and pressed bends (with good flow characteristics) with a radius twice as large as diameter (up to 400 mm) for exhaust air/dust extraction plants.
Mass production, all products of the same quality, subsequent components identical.
|
|
Ducting
Nordfab QF clipped ducting
is an adaptable, smart looking, easy to fit or extend ducting system. It can be quickly dismantled and reconfigured according to the needs of your site. It is suitable for all general dust extraction applications at ambient temperature and particularly for wood, panel production and furniture manufacture. A complete range of compatible accessories and installation components enable professional installations with economy.
Flanged ducting
in heavier gauges is available for more demanding applications for example with abrasive dusts such as metals and quarry products and also for higher temperature applications including flue gas from foundry processes and incineration.
|
|
- Stainless steel pipe
- Diameters 22 to 100 mm (3/4'' to 4'')
- Quick connection, easy to install
- Efficient flow, no leaks
- 10 years guarantee
|
|
Tyco Fire Suppression & Building Products' UNI Channel systems have been recently reviewed into one comprehensive product line that can offer solutions to every construction issue. As well as a range of conventional fittings, you could choose our fast fix system, saving you time and money.
The UNI Channel system offers 4 channel types, varying in thickness and produced in different lengths. Imprinted length markings and serration inside the channel to ensure a better grip of the channel nut have been introduced, and the development of a new Kwik-Fix nut allows fast installation.
- One range of channels can be used conventionally or with the fast fix system
- One type of Kwik-Fix nut for all channel types
- Complete range of fittings and and accessories for support structures
- Accessories for making beam or concrete connections
|
|
Tyco Fire Suppression & Building Products' support systems are a result of close co-operation between manufacturer, engineer, distributor and customer. The support systems range comprises:
- Unistrut metal framing products and the new Kwikstrut fittings
- Wopf pipe supports
- Suspension fasteners
- Electrical supports including cable & basket trays and cable ladders.
We can assist you with the design of your installation, help with material take-off and selection of the right product for the right application. If you have a large project, ask for our software calculation package.
|
|
The range in PVDF comprises a complete series of pipes, fittings for heat socket fusion, manual and automatic valves for use in the construction of process lines and service lines to convey industrial fluids in the operating temperature range from - 40°C to 140°C.
The entire range is produced in SOLEF™ resins by SOLVAY S.A. classified according to ASTM D 3222 and compliant with requirements stated in ISO/WD 10931 for the use of PVDF pipeline systems in industrial processes.
|
|
Nuflo and anti-syphon traps.
Manufactured in white polypropylene and Kite marked to British Standard 3942, the Nuflo range includes over 80 models.
Nuflo Traps are in 32mm and 40mm sizes and a wide variety of seal depths.
Nuflo’s Universal Compression Joints accept all plastic waste pipes and Imperial and metric Copper piping.
A range of Anti-Siphon Traps, True Metric Continental Traps, Space Saving Undersink Kits, Chromium Plated Bottle Traps and Condensation Traps further enhance the comprehensive range
|
|
PTFE lined pipes DIN 2848/2874 DN 15 DN 600 PN 10
Standard version: 1 fixed flages, 1 lap joint flange
Carbon steel Body
|
|
|
Enhance performance and product life by using the material best suited to YOUR application CoorsTek Materials Professionals help you choose from a multitude of advanced ceramics and high-performance plastics like Alumina, Zirconia, Silicon Carbide and others PTFE, UHMW.
|
|
|
|
