|
|
|
Autoclave Engineers offers Seamless High Pressure Heavy Wall stainless steel tubing for pressures above 10,000 psi (690 bar) up to over 150,000 psi (10,000 bar). Also available in specialty materials such as Inconel, Duplex, Super Duplex, and others. A complete line of Valves, and Fittings are also available.
|
|
|
|
|
|
Top Line Electropolished tubing sets the standard for service in applications requiring finishes to 15RA maximum. Available in sizes from 1/2" to 4" OD, this full finished stainless steel tubing is available from stock or direct from the mill in 20 foot lengths. All electropolished tubing is fully tested and marked per ASTM A450 requirements. 3
All Top line electropolished tubing is packaged using protective 6 mil poly sleeving with air tight end caps. The tubing is then packageg in wood or Tri-Wall corrugated cartons for maximum protection during shipment.
Finish: Electropolished Tubing is standard with a 15RA max ID with bright annealed/mill OD (ASME BPE surface finish code SFT4). Mechanically polished OD to 32RA or 20RA available on application. The same product is available with a 10RA max. surface finish ID.
Annealing: All tubing is Bright Annealed to a minimum of 1900 degrees F (1040° C) and rapidly quenched.
Cleaning: All Top Line electropolished tubing is rinsed with low TOC de-ionized water. The tubing is then dry purged with 99.998% pure Nitrogen which is filtered to .003 micron at the point of use. The cleaning and packaging is done in a class 100< cleanroom.
|
|
ERW Steel Pipe
Outside Diameter: ø 114mm - ø 356mm (4"-14")
Wall Thickness: 3.0-12.7mm (1/8"-1/2")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 3-12.3m (10'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 150,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
LSAW Steel Pipe (JCOE X 2 Mills)
Outside Diameter: ø 406mm - ø1829mm (16"-72")
Wall Thickness: 6.4-60mm (1/4"- 21/8")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 3-12.3m (10'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 550,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
LSAW Steel Pipe (UOE)
Outside Diameter: ø 508- ø1118mm (20"-44")
Wall Thickness: 6.4-25.4mm (1/4"-1")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 9-12.3m (30'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 600,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
Product Details
Product Code: USH33
Product Description: 82mm U/Ground Single Sckt T/Cotta (1/20)
Brand: Polypipe
Colour: 82mm U/Ground Single Sckt T/Cotta (1/20)
Material: PVC
Product Dimensions
Outside Diameter: 82
|
|
|
Nylon tubing is a popular choice for low pressure pneumatic applications because of its combination of flexibility and toughness. Nycoil uses a heat and light stabilized, very flexible high grade Nylon 12 compound that yields the finest quality tubing available. Some of the qualities of tubing extruded from the Nylon 12 raw material are good chemical resistance, low water absorption and superior dimensional stability. Nylon is the most recommended tubing material for all types of pneumatic circuits.
|
|
|
|
|
|
The use of under floor heating typically allows room temperatures to be reduced by 1°-2°C when compared with radiators, while still providing the same level of comfort. Each 1°C reduction in room temperature reduces fuel consumption by 6%. This means it is cheaper to run and gives the house a reduced carbon footprint.
As underfloor central heating is the enabler to maximise the use of low or zero carbon technologies for heat generation such as air source heat pumps or geothermal systems, it is key to sustainable indoor environments.
At Polypipe we manufacture the most complete range of floor heating systems for every application. Solid floor systems provide 'thermal mass' solutions and incorporate our unique floor panel, which enhances performance and requires less screed material than other systems.
The patented Overlay system provides a unique retro fit underfloor system, unlocking for the first time the massive potential for energy efficient under floor central heating in existing dwellings.
|
|
|
Pipes out of polyethylene may be applied across the range of high energy radiation. Pipes out of PE are well established for drainage of radioactive sewage water from laboratories arvj as cooling water piping systems for the nuclear energy industry. The usual radioactive sewage waters contain beta and gamma rays. PE piping systems do not become radioactive, even after many years of use. Also in environment of higher radio activity, pipes out of PE are not damaged if they are not exposed during their complete operation time to a larger, regularly spread radiation dose of < 10 i Gray.
|
|
|
|
|
|
MULTI-THERM™ 500 is the best prefabricated, preinsulated piping system for the distribution of low to high pressure steam, high temperature hot water and general fluid transportation systems. The design eliminates corrosion and reduces energy loss.
MULTI-THERM™ 500 is the best drainable, dryable and testable, prefabricated, preinsulated piping system for the distribution of low to super heated high pressure steam, high temperature hot water and general fluid transportation systems. The outer conduit is insulated with polyurethane foam insulation and has a jacket of filament wound fiberglass or extruded HDPE jacket. MULTI-THERM™ 500 is a smooth wall, spiral welded, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Leak Detection and Location system.
- Temp Range: 250°F to 750°F (standard), above 750°F (special)
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
POLYTHERM® is the best system we offer. It is a fiberglass jacketed, polyurethane foam insulated piping system for above and belowground distribution of liquids from -320°F to 250°F.
POLYTHERM® is a fiberglass jacketed, spray applied polyurethane foam insulated piping system for above and below ground distribution of liquids from -320°F to 250°F. PERMA-PIPE's multi-directional filament winding process produces a high strength fiberglass reinforced polyester resin jacket over the insulation for maximum protection from the environment. This high-strength fiberglass jacket is applied to systems having an outside diameter as large as 48 inches. Electric heat tracing is an option with this system.
POLYTHERM®'s spray insulation process assures void-free insulation. By applying insulation before the jacket is applied, complete visual inspection of the insulation is performed. This process assures void-free insulation and therefore, maximum thermal efficiency to provide optimum performance of cryogenic and heat thermal distribution systems. The POLYTHERM® system is fully engineered to job specifications, thereby reducing field costs by providing custom made, factory-fabricated fittings which reduce the number of field connections as compared to the field kit method.
- Temp Range: -320ºF to 250ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter 1/ 2" - 36" (standard), Nom. Length 20' and 40'
|
|
POLYTHERM® is the best system we offer. It is a fiberglass jacketed, polyurethane foam insulated piping system for above and belowground distribution of liquids from -320°F to 250°F.
LO-TEMP - HI-GARD™, is a designed for the distribution of fluids aboveground at temperatures up to 250 ºF. Based on customers specifications, this is a prefabricated system with all fittings attached to straight sections.
ULTRA-NW™ is an advanced prefabricated, secondary containment piping system for hazardous chemicals, process waste and general fluid transportation. It is a fiberglass clad stainless steel conduit system with no need for cathodic protection.
|
|
|
|
|
|
ESCON-A®/ FERRO-SHIELD™ is the original prefabricated, preinsulated piping system for the distribution of low to high pressure steam, high temperature hot water, and general fluid transportation systems.
ESCON-A®/ FERRO-SHIELD™ is the original drainable, dryable and testable, prefabricated, preinsulated piping system for the distribution of low to super heated high pressure steam, high temperature hot water and general fluid transportation systems. The outer conduit is coated with our Elephant Hide urethane coating which provides an outstanding corrosion resistant covering. ESCON-A®/ FERRO-SHIELD™ is a smooth wall, spiral welded, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation, but we recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Leak Detection and Location system, or Cathodic Protection (optional).
- Temp Range: 250°F to 750°F (standard), above 750°F (special)
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
ULTRA-HT™ is an advanced preinsulated secondary containment piping system for general fluid transportation that requires an insulated steel containment. No need for cathodic protection.
ULTRA-HT™ is the designed for maintaining fluid temperature while containing hazardous fluids. This system complies with Federal regulations for secondary containment of hazardous fluids, that require insulation to maintain their temperature. Drainable, dryable and testable, prefabricated this secondary contained piping system is designed for the distribution of jet fuel, radioactive waste, bio-process waste and chemical transfer. ULTRA-HT™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding .100 mils thick and designed to withstand a 35,000 volt holiday test. ULTRA-HT™ is supplied with stainless or other high alloy pipe and containment. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
PREMANT®
Ultramodern technology for efficient production
Our pipes are available in dimensions from DN 20 to DN 1000; the types of foam insulation, medium pipes and the system for the monitoring wires can be selected freely.
Thanks to our modern production facilities, we can react rapidly to your requirements.
|
|
Seamless tubes size range »
1.0mm (0.04") to 50.8mm (2") OD. Straight lengths up to 16m (51ft), seamless coiled tubing 6.35mm (1/4") thru to 25.4mm (1") OD.
Our product range consists of straight and coiled tubing. These tubes can be either seamless, welded or welded and drawn.
|
|
SEAMLESS HYDRAULIC LINE TUBES, PHOSPHATED OR GALVANISED FOR PRESSURE AND RETURN PIPING
Material SI 37.4 (E235+N), St 52.4 nbk(E355+N)
Tol. DIN 2391/C or EN 10304-4
Dimensional Range
4,00 x 1.00 mm up to 80,00 x 10,00 mm also in inch-sizes and free Chromium VI
|
|
Welded, welded and drawn tubes size range »
Up to 38.1mm (1 1/2") OD. Straight lengths up to 16m (51ft), coil tubes (with orbital joints) up to 10000m (33000ft) long.
Our product range consists of straight and coiled tubing. These tubes can be either seamless, welded or welded and drawn.
|
|
Sanpress-Pipe 1.4521, stainless steel, for drinking water installations, in 6 m rods,
Sanpress XL-Pipe 1.4521, stainless steel, for drinking water installations, in 6 m rods,
Sanpress-Pipe 1.4401, stainless steel, for drinking water- and gas installations, in 6 m rods
Sanpress XL-Pipe 1.4401, stainless steel, for drinking water- and gas installations, in 6 m rods
Sanpress-Pipe bow 15°, stainless steel
Sanpress XL-Pipe bow 15°, stainless stee
Sanpress-Pipe bow 30°, stainless steel
Sanpress XL-Pipe bow 30°, stainless steel,
|
|
WELDED CYLINDER TUBES IN STAINLESS STEEL
Material: AISI 304; 316 L; 316 Tl
Tol. OD DIN 2463
Tol. ID ISO-Tolerance Field H9-H11
Cenler Line Average of Interior Surface drawn Ra max. 1,0 µm
Dimensional Range: ID ø8 - 200 mm
|
|
|
|
|
|
High Quality Fluoropolymer Extrusion
SAT, an ISO 9001 certified company, produces tubing utilizing specially designed extruders and extrusion processes. Our tubing is made using only ultra-high purity (UHP) PFA and FEP raw materials. Thanks to laser technology and state-of-the-art systems, our tubing’s O.D. and I.D. are kept under constant control, as is electrostatic charge neutralization.
Tube cleanliness is ensured during and after extrusion as a result of our contamination control process. In fact, each tube unit receives a positive nitrogen surge and is then immediately capped and packaged in separate, heat-sealed, double polyethylene bags. The tube coils are then stocked in clean room.
Low Extractables for a High-Tech World
Contaminants are a problem you can’t afford. In fact, impurities result in lower chip yields, higher costs and lower profit margins. Why settle for anything less than high-purity products for your manufacturing processes?
SAT’s PFA and FEP Tubings have very low levels of extractable metals, and this high purity characteristic results in higher wafer yields for the semiconductor industry. Furthermore, high purity means lower costs thanks to reduced contamination, and higher profits due to fewer product defects.
SAT’s PFA and FEP Tubing Features:
* Low levels of extractable fluoride ions
* High crack resistance and strength
* Excellent chemical resistance
* High temperature resistance
* Low chemical carryover and permeability
* Non-flammable
* Low ionic attraction
* High weather and aging resistance
* Excellent dielectric properties
* Non-stick
* High mechanical abilities
* High burst pressur
|
|
|
Ductile iron pipes have the corrosion resistance of cast iron and almost the same strength and ductility of steel. Because of their high reliability, ductile iron pipes are widely used in pipelines to convey potable water, sewage water, agricultural or industrial water, gas, etc. Recently, there has been a strong demand for earthquake-resistance ductile iron pipes, especially those employing NS-type earthquake resistance joints, with about 50 percent of our current domestic-oriented shipments being earthquake-proof piping.
|
|
|
This heat transport pipe consists of an inner pipe with a layer of thermal insulating material, and a reinforcing layer formed around the inner pipe. Responding to the need for transporting heated mediums such as steam, and heated or chilled water, this product has been developed and is contributing to the efficient use of energy. For example, heat transport pipes have been installed in area-wide air conditioning systems and other facilities that utilize excess and waste heat or geothermal energy.
|
|
MJ - Metal Tube Jacketed (Single Metal Tube)
Copper Tubes:
1/4” OD x .030” Wall
3/8” OD x .032” Wall
1/2” OD x .035” Wall
Welded Stainless Steel Tube:
1/4” OD x .035” Wall
3/8” OD x .035” Wall
1/2” OD x .035” Wall
|
|
This Standard applies to seamless precision steel tubes; and, in compliance with ISO/DIS 3304, those tube dimensions have een selectied from the range of manufactura le tu e dimensions which are mainly used as design elements
If tubes having the tolerances and are produced according to the technical conditions of deivery as specified in this Standard are to e used as pipelines, then the dimensions specified in DIN 2448 may from time to time be used. These tubes must be ordered according to quality grade C.
|
|
Standard：
API SPEC 5CT Standard of American Petroleum Institute
Application：
Seamless steel tubes for oil casing and tubing in oil wells
Model N0．of steel tubes：
J55，N80，L80，P110 etc．
|
|
We can makes and markets cold-drawn and hot rolled seamless steel pipes and cold-drawn special-section seamless pipes which are widely applied in the industries of petrochemical, boiler, automobile, mechanical, construction, chain, electric of the company is 80000t. Our factories through ISO9001:2000 certificate, has aggressive leadships and outstanding professionals.
Specifications:
Size: (Φ6 - Φ680) x (0.5 - 87) mm, but we can also produce other specification according to the customers’ requirements.
|
|
ALL ENQUIRIES MUST BE WRITTEN IN ENGLISH.
UNFORTUNATELY, ENQUIRIES WRITTEN IN OTHER LANGUAGES CANNOT BE ANSWERED
|
|
Stainless Steel Pipe
Seamless to EN ISO 1127
Produced in approx. 6 m lengths
sf 800 m
Stainless Steel Pipe
sf 800 m
Capillary Tube
Microtubing
sf 800 z
Imperial
Stainless Steel Pipe
|
|
|
This pile was developed based on the ductile pipe that has long been used for water pipelines, and is usually used as a bearing pile for small buildings. The strength is higher than the commonly used structural carbon steel, and the corrosion resistance is more than two times higher. The ducpiles securely support a building, contributing to improving the safety of a house or other small structure.
|
|
|
|
