|
|
A large range of PTFE lined piping adn fittings that resist to corrosion and answering all your applications :
· PTFE lined elbow
· PTFE lined tee
· PTFE lined reduction flange
· PTFE lined cross
· PTFE lined instrument tee
· PTFE lined piping
· PFA check valves
ND 25 to ND 600.
From 100 to 8000 mm
Up to 230°C
Up to 25 bars
ASME/DIN
PTFE Antistatique (noir)
Heavy duty thickness
Vacuum designed application
|
|
Mass production, all products of the same quality, subsequent components identical.
Extraction of harmful substances like dust, steam and solvents
Our pull-ring system with U-shaped seals can be used in almost every line of business because it is tight against condensed liquids.
Certificates "shock explosion proof up to 3 bar overpressure"are available on request (angle flange connection is shock explosion proof up to 10 bar).
|
|
|
|
|
|
GALVA-GARD®, "The Ultimate Corrosion Fighter" is a prefabricated, preinsulated, fiberglass clad galvanized steel conduit system for low to high pressure steam, HTHW and general fluid transportation.
GALVA-GARD® the original "corrosion fighter" just got better. As always, galvanization is applied to the exterior, as well as the interior of the outer pipe providing a clean, corrosion resistant system for underground heat distribution. Now PERMA-PIPE® has added a thick cladding of fiberglass reinforced plastic on top of the galvanized system for maximum resistance to adverse corrosion and environmental conditions. There is no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick and designed to withstand a 35,000 volt holiday test. GALVA-GARD® is a smooth wall, hot dipped galvanized, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Energy Loss Detection and Location system and electric heat tracing.
- Temp Range: 250°F to 750°F (standard), above 750°F (special)
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
XTRU-THERM®, our "State of the Art" preinsulated piping system for fluids from cryogenic temperatures up to 250ºF. The extruded HDPE jacket results in a completely bonded system that moves as a single unit for maximum efficiency and service life.
XTRU-THERM® is a process driven product, developed to eliminate problems inherent in foam injected systems. The pipe is insulated using a special spray applied continuos feed insulating process which works in line with our extruded high density polyethylene plastic material. The JACKET remains flexible at low temperatures and has a higher temperature rating than PVC. The HDPE jacket has been specifically designed to bond to the insulation. Designed for both above and underground insulated pipe applications. The hardness, tensile and flexural strength, toughness, diameter and thickness of the jacket are controlled.
The foam insulation is spray-applied and rises, unrestricted, to its final thickness. The free rise allows cell structure of the foam to be uniform in all directions. Because the foam is spray-applied and not injected, XTRU-THERM® is guaranteed to be 100% void-free. The blowing agent (HCFC, a gas that expands the foam and creates cell structure) does not dissipate from the cell like other water-based agents. Therefore, the cell structure and thermal value is maintained and the foam will not shrink.
- Temp Range: -320ºF to 250ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter 1/ 2" - 36" (standard), Nom. Length 20' and 40'
|
|
|
|
|
|
The use of under floor heating typically allows room temperatures to be reduced by 1°-2°C when compared with radiators, while still providing the same level of comfort. Each 1°C reduction in room temperature reduces fuel consumption by 6%. This means it is cheaper to run and gives the house a reduced carbon footprint.
As underfloor central heating is the enabler to maximise the use of low or zero carbon technologies for heat generation such as air source heat pumps or geothermal systems, it is key to sustainable indoor environments.
At Polypipe we manufacture the most complete range of floor heating systems for every application. Solid floor systems provide 'thermal mass' solutions and incorporate our unique floor panel, which enhances performance and requires less screed material than other systems.
The patented Overlay system provides a unique retro fit underfloor system, unlocking for the first time the massive potential for energy efficient under floor central heating in existing dwellings.
|
|
|
|
|
|
MULTI-THERM™ 500 is the best prefabricated, preinsulated piping system for the distribution of low to high pressure steam, high temperature hot water and general fluid transportation systems. The design eliminates corrosion and reduces energy loss.
MULTI-THERM™ 500 is the best drainable, dryable and testable, prefabricated, preinsulated piping system for the distribution of low to super heated high pressure steam, high temperature hot water and general fluid transportation systems. The outer conduit is insulated with polyurethane foam insulation and has a jacket of filament wound fiberglass or extruded HDPE jacket. MULTI-THERM™ 500 is a smooth wall, spiral welded, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Leak Detection and Location system.
- Temp Range: 250°F to 750°F (standard), above 750°F (special)
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
POLYTHERM® is the best system we offer. It is a fiberglass jacketed, polyurethane foam insulated piping system for above and belowground distribution of liquids from -320°F to 250°F.
POLYTHERM® is a fiberglass jacketed, spray applied polyurethane foam insulated piping system for above and below ground distribution of liquids from -320°F to 250°F. PERMA-PIPE's multi-directional filament winding process produces a high strength fiberglass reinforced polyester resin jacket over the insulation for maximum protection from the environment. This high-strength fiberglass jacket is applied to systems having an outside diameter as large as 48 inches. Electric heat tracing is an option with this system.
POLYTHERM®'s spray insulation process assures void-free insulation. By applying insulation before the jacket is applied, complete visual inspection of the insulation is performed. This process assures void-free insulation and therefore, maximum thermal efficiency to provide optimum performance of cryogenic and heat thermal distribution systems. The POLYTHERM® system is fully engineered to job specifications, thereby reducing field costs by providing custom made, factory-fabricated fittings which reduce the number of field connections as compared to the field kit method.
- Temp Range: -320ºF to 250ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter 1/ 2" - 36" (standard), Nom. Length 20' and 40'
|
|
POLYTHERM® is the best system we offer. It is a fiberglass jacketed, polyurethane foam insulated piping system for above and belowground distribution of liquids from -320°F to 250°F.
LO-TEMP - HI-GARD™, is a designed for the distribution of fluids aboveground at temperatures up to 250 ºF. Based on customers specifications, this is a prefabricated system with all fittings attached to straight sections.
ULTRA-NW™ is an advanced prefabricated, secondary containment piping system for hazardous chemicals, process waste and general fluid transportation. It is a fiberglass clad stainless steel conduit system with no need for cathodic protection.
|
|
|
|
|
|
ESCON-A®/ FERRO-SHIELD™ is the original prefabricated, preinsulated piping system for the distribution of low to high pressure steam, high temperature hot water, and general fluid transportation systems.
ESCON-A®/ FERRO-SHIELD™ is the original drainable, dryable and testable, prefabricated, preinsulated piping system for the distribution of low to super heated high pressure steam, high temperature hot water and general fluid transportation systems. The outer conduit is coated with our Elephant Hide urethane coating which provides an outstanding corrosion resistant covering. ESCON-A®/ FERRO-SHIELD™ is a smooth wall, spiral welded, 10 gauge steel conduit. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation, but we recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a Leak Detection and Location system, or Cathodic Protection (optional).
- Temp Range: 250°F to 750°F (standard), above 750°F (special)
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
ULTRA-HT™ is an advanced preinsulated secondary containment piping system for general fluid transportation that requires an insulated steel containment. No need for cathodic protection.
ULTRA-HT™ is the designed for maintaining fluid temperature while containing hazardous fluids. This system complies with Federal regulations for secondary containment of hazardous fluids, that require insulation to maintain their temperature. Drainable, dryable and testable, prefabricated this secondary contained piping system is designed for the distribution of jet fuel, radioactive waste, bio-process waste and chemical transfer. ULTRA-HT™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding .100 mils thick and designed to withstand a 35,000 volt holiday test. ULTRA-HT™ is supplied with stainless or other high alloy pipe and containment. Single or multiple steel carrier pipes can be insulated with any type of pipe insulation. We recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
PTFE lined pipes DIN 2848/2874 DN 15 DN 600 PN 10
Standard version: 1 fixed flages, 1 lap joint flange
Carbon steel Body
|
|
- Product Code: PS1030
- Product Description: 225mm x 3m Polysewer Plain Ended Class 8
- Material: uPVC
- Length: 3
- Outside Diameter: 250
- Inside Diameter: 22
|
|
BRUGG-STAMANT®
Guaranteed environmental safety
BRUGG STAMANT Safety Pipe ® is a dual pipe system prefabricated in construction units; it is especially suitable as a pipe to transport combustible or non-combustible media and gases that endanger water.
Optical and acoustic alarms are triggered in case of a leak if the pipe is used in conjunction with a leakage indicator.
Conditions and requirements
Conventional engineering of dual-wall pipe systems to transport hazardous substances must meet the highest requirements in terms of expert design and optimal technology - especially when larger dimensions are involved. As you would expect, we guarantee compliance with all conditions for fire and explosion prevention and water protection.
|
|
|
|
|
|
ULTRA-NW™ is an advanced prefabricated, secondary containment piping system for hazardous chemicals, process waste and general fluid transportation. It is a fiberglass clad stainless steel conduit system with no need for cathodic protection.
ULTRA-NW™ is the next generation for complying with Federal regulations for secondary containment of hazardous fluids, this drainable, dryable and testable, prefabricated, secondary contained piping system is designed for the distribution of jet fuel, radioactive waste, Bio-process waste and chemical transfer. ULTRA-NW™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick, and designed to withstand a 35,000 volt holiday test. ULTRA-NW™ is supplied with stainless or other high alloy pipe and containment. Single or multiple steel carrier pipes, can be insulated with any type of pipe insulation, we recommend mineral wool that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
|
|
|
|
ULTRA-FS™ is an advanced prefabricated, secondary containment piping system for chemicals, process waste, fuel systems and general fluid transportation is a fiberglass clad steel conduit system with no need for cathodic protection.
ULTRA-FS™ is the next generation for complying with Federal regulations for secondary containment of hazardous fluids, this drainable, dryable and testable, prefabricated, secondary contained piping system is designed for the distribution of hydrocarbons, process waste and chemical transfer. ULTRA-FS™ can be used for above and below grade systems, with no need for cathodic protection. The outer conduit is clad with our filament wound fiberglass cladding 100 mils thick, and designed to withstand a 35,000 volt holiday test. ULTRA-FS™ is a smooth wall, minimum 10 gauge steel conduit. Single or multiple steel carrier pipes, can be insulated with any type of pipe insulation. We recommend mineral wool insulation that has passed a certified boiling test. Other options for this piping system include a PermAlert Leak Detection and Location system, and electric heat tracing.
- Temp Range: 32ºF to 750ºF
- Max Pressure: Determined by the carrier pipe selected
- Pipe Sizes: Nom. Diameter ½" - 44", Nom. Length 20' and 40'
|
|
Sewerdrain System
Sewerdrain Pipe and fittings to BS 5481 (EN 1401) were established in the early 1970’s, gaining recognition for a wide range of domestic and civil engineering applications, and have been have been accepted under the building regulations and ‘Sewers for Adoption’, where their performance has been well proven.
Supplied in 3 metre or 6 metre lengths, with socketed or plain ended.
|
|
Waste water disposal systems in semi-conductor, pharmaceutical and bio industry
Transport lines in nuclear, gas, oil and chemical industry
Transport lines of dangerous and corrosive
waste water in groundwater protection areas
|
|
Cold Water Supply
Polypipe manufactures blue polyethylene potable water pipes in 20mm to 63mm diameter. They are manufactured to BS 6572 and are complemented by a full range of Polyfit push-fit and Polyfast compression fittings. Adaptors are available for connections to copper, lead and imperial polyethylene pipes. Service pipes are available in coil sizes of 25, 50, 100 and 150m.
|
|
|
Ductile iron pipes have the corrosion resistance of cast iron and almost the same strength and ductility of steel. Because of their high reliability, ductile iron pipes are widely used in pipelines to convey potable water, sewage water, agricultural or industrial water, gas, etc. Recently, there has been a strong demand for earthquake-resistance ductile iron pipes, especially those employing NS-type earthquake resistance joints, with about 50 percent of our current domestic-oriented shipments being earthquake-proof piping.
|
|
|
This heat transport pipe consists of an inner pipe with a layer of thermal insulating material, and a reinforcing layer formed around the inner pipe. Responding to the need for transporting heated mediums such as steam, and heated or chilled water, this product has been developed and is contributing to the efficient use of energy. For example, heat transport pipes have been installed in area-wide air conditioning systems and other facilities that utilize excess and waste heat or geothermal energy.
|
|
|
This pile was developed based on the ductile pipe that has long been used for water pipelines, and is usually used as a bearing pile for small buildings. The strength is higher than the commonly used structural carbon steel, and the corrosion resistance is more than two times higher. The ducpiles securely support a building, contributing to improving the safety of a house or other small structure.
|
|
|
Autoclave Engineers offers Seamless High Pressure Heavy Wall stainless steel tubing for pressures above 10,000 psi (690 bar) up to over 150,000 psi (10,000 bar). Also available in specialty materials such as Inconel, Duplex, Super Duplex, and others. A complete line of Valves, and Fittings are also available.
|
|
Top Line maintains a large inventory of welded stainless steel tubing to meet your immediate needs. Our warehouse is able to quickly ship tubing in lengths up to 20 feet. Each tubing order is processed promptly and packaged in tri-wall corrugated cartons equipped with wooded ends to protect each piece from damage.
Applications which require only the finest in tubing, with close adherence to tolerances, readily prefer tubing from Top Line. We pride ourselves on providing the finest tubing at a competitive price. Tubing types 304 and 316L are available in sizes from 1/2" OD to 12" OD – produced to ASTM specifications A249, A269, A270 or A778. Other dia-meters, specifications and lengths are available on special order. Finishes available range from Bright Annealed (mill) to 240 grit mechanical ID and OD and meet all USDA and 3A sanitary standards. Pharmaceutical - Grade Tubing is also available from Top Line.
|
|
Fluoropolymer Tubing
* Stock PTFE sizes from 4mm to 12mm OD
* Stock FEP sizes from 4mm to 12mm OD
* Suitable for food use
* Non hardening
* Non stick
* Durable
* Excellent chemical resistance
|
|
|
|
|
|
Top Line Electropolished tubing sets the standard for service in applications requiring finishes to 15RA maximum. Available in sizes from 1/2" to 4" OD, this full finished stainless steel tubing is available from stock or direct from the mill in 20 foot lengths. All electropolished tubing is fully tested and marked per ASTM A450 requirements. 3
All Top line electropolished tubing is packaged using protective 6 mil poly sleeving with air tight end caps. The tubing is then packageg in wood or Tri-Wall corrugated cartons for maximum protection during shipment.
Finish: Electropolished Tubing is standard with a 15RA max ID with bright annealed/mill OD (ASME BPE surface finish code SFT4). Mechanically polished OD to 32RA or 20RA available on application. The same product is available with a 10RA max. surface finish ID.
Annealing: All tubing is Bright Annealed to a minimum of 1900 degrees F (1040° C) and rapidly quenched.
Cleaning: All Top Line electropolished tubing is rinsed with low TOC de-ionized water. The tubing is then dry purged with 99.998% pure Nitrogen which is filtered to .003 micron at the point of use. The cleaning and packaging is done in a class 100< cleanroom.
|
|
LSAW Steel Pipe (JCOE X 2 Mills)
Outside Diameter: ø 406mm - ø1829mm (16"-72")
Wall Thickness: 6.4-60mm (1/4"- 21/8")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 3-12.3m (10'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 550,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
ERW Steel Pipe
Outside Diameter: ø 114mm - ø 356mm (4"-14")
Wall Thickness: 3.0-12.7mm (1/8"-1/2")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 3-12.3m (10'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 150,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
LSAW Steel Pipe (UOE)
Outside Diameter: ø 508- ø1118mm (20"-44")
Wall Thickness: 6.4-25.4mm (1/4"-1")
Quality Standards: API, DNV, BS, ASTM, JIS, DIN, GB, ISO, DEP
Length: 9-12.3m (30'-40')
Grades: GB/T9711 L190-L555 (API 5L A-X80)
Annual Capacity: 600,000 Metric Tone
PLEASE WRITE ALL ENQUIRIES IN ENGLISH ONLY! THANKS!
|
|
Round pipes of the company h.hiendl GmbH & CO. Kg
Hiendl of round pipes are made from natural fiber strengthened composite materials of the Hiendl NFC® of material system as well as of purely synthetic thermoplastics (polypropylene, polyethylene, ABS, PVC, PP). The selection of the material is determined in each case by the characteristics, which are optimal for application. The universal products of Hiendl NFC® and of conventional plastics are manufactured for the construction industry, the interior fittings, the laboratory, charge, measurement and the furniture making. With Hiendl NFC® the fossil raw materials common with plastics are replaced to substantial portions by regenerating raw materials. This reduces the load of the atmosphere by CO2-Emissionen. In the comparison e.g. to aluminum - also this material can be replaced by Hiendl NFC® - consumption at primary energy is considerably smaller in the production and processing.
|
|
|
|
|
|
The Exel pull-winding, co-winding and prepreg wrapping techniques enables the manufacture of high-performance composite tubes while optimizing the structure and minimizing the use of raw material. The wide range of Exel tubes from 3mm to 300mm diameter, together with suitable wall thickness, different types of reinforcement and resins allow you to have an optimized product according to your needs.
The choice of reinforcing materials is determined by the technical demands, such as weight, stiffness and strength, and its ability to insulate heat and electricity. Glass fibre is a widely used reinforcing material that gives the product the following properties: light weight, durability, stiffness and is readily pigmented. Carbon fibre enables the manufacture of even lighter and stiffer tube. It should be noted that carbon fibre conducts electricity. Although carbon fibre tubes are black, they can be coloured by introducing a glass fibre surface layer. A hybrid is a product that combines more than one material. It is thus possible to optimize lightness, stiffness, strength and costs.
Tubes usually have a non-wowen surface, and the surface resin is pigmented throughout. The pigment can be selected from numerous standard colours, for instance, according to the RAL or PANTONE colour codes. If requested, the colour can be made to the customer’s requirements. Tubes may also be given a spiral surface. The customer’s name or some other information may be printed on the tube surface.
Exel quality and environment policy complies with the requirements of the standards ISO 9001:2000 and ISO 14001 (Bureau Veritas Certification).
|
|
|
|
