|
|
Standard characteristics :
- Maximum pressure : 4140 bar (60,000 psi).
- Working presure : from 500 up to 3500 bar (7,200 to 50,000 psi).
- Max. flow rate : 10 l/min at 3500 bar (50,000 psi).
- 1 SUGINO intensifier (redundancy in option), 1 UHP accumulator.
- Soundproofed casing.
- Complete hydraulic unit, with 10 µ filtration, and water cooling.
- Safety valve for automatic bleed-down of the UHP circuit.
- PLC controller : support for the maintenance and the follow-up of the functioning.
Advantages :
- Pumps perfectly adapted to all industry sectors : automotive, mechanics, aeronautics, food industry, and designed for a use in 3 shifts, 7 days a week.
- Turnkey equipments.
- Pumps with the UHP components reaching the best life times of the market.
- Decrease of the running costs.
|
|
BI30M Oil hydraulic bent pump, 32cc/rot, aplication pressure-up to 350bar, peak pressure-400bar
BI40M Oil hydraulic bent pump, 42cc/rot, aplication pressure-up to 350bar, peak pressure-400bar
BI50M Oil hydraulic bent pump, 50cc/rot, aplication pressure-up to 350bar, peak pressure-400bar
BI60M7 Oil hydraulic bent pump, 60cc/rot, aplication pressure-up to 350bar, peak pressure-400bar
BI80M7 Oil hydraulic bent pump, 81cc/rot, aplication pressure-up to 300bar, peak pressure-350bar
BI80P Oil hydraulic bent pump, 80cc/rot, aplication pressure-up to 350bar, peak pressure-400bar
BI110P7 Oil hydraulic bent pump, 108cc/rot, aplication pressure-up to 350bar, peak pressure-400bar
|
|
A majority of the variable piston pumps on the
market were designed decades ago, and very
few modifications have been made since then.
When Parker Hannifin decided to develop a new line of
variable piston pumps for the mobile market, it was
obvious to us that we needed to listen to and understand
our markets. We needed to get our hands around the
latest requirements and move the development forward.
Instead of starting the design work at the drawing board,
we went out to our customers and asked them what
characteristics they required from a new pump. Very
soon, the most important requirements became obvious.
OEM’s were looking for pumps that were easy and
inexpensive to install, had a low noise level, lasted a long
time, had a high self-priming speed and were equipped
to handle future pump controls.
With this in mind, our product team went to work on
perfecting our new line of pumps. The result: the new
Variable Piston Pump Series P2/P3.
|
|
|
|
|
|
The variable volume and pressure compensated design simplifies circuit design, and reduces heat buildup and noise. Four pump control options permit the designer to choose the most efficient means to power his hydraulic equipment. Choices include the standard pressure compensator control, remote pressure control, load sensing control, and horsepower limiting control.
Brass piston slippers pivot and rotate to equalize wear while a fluid passage through the slipper reduces loading and provides lubrication for the piston shoe and wear plate. Hardened swash plate and trunnion pins provide rugged support for the piston block and associated rotating group components.
Efficiently designed porting reduces noise at all pressure and flow levels for quiet, efficient operation that eliminates the need for noise shrouds. The rugged, cast iron body is thicker at stress points which contributes to quiet operation.
Specifications
Mountings: SAE 2 bolt mountings. SAE 'A', SAE' B', and SAE 'C'
Tandem pump drive capabilities
Capacities: 6, 10, 15, 20 29 GPM @ 1750 RPM
Displacements: .88, 1.26, 2.09, 2.62, and 3.78 cubic inches per revolution
Pressure Compensation Ranges: 200 to 3500 PSI continuous duty, up to 4000 PSI intermittent duty
Recommended Fluids:
Petroleum based fluids are recommended. Fluids should be designated by the fluid manufacturer for use in hydraulic systems. Fluids should contain inhibitors to prevent rust and oxidation and should contain anti-wear, anti-foam, and deaerating agents. For other fluid types, please contact your Continental Hydraulics representative.
Recommended Operating Viscosity
Petroleum based fluids:
Optimum - 140 sus (30 Cst.)
Continuous Minimum - 60 sus (10 Cst.)
Continuous Maximum - 750 sus (160 Cst.)
Max cold start up 7500 SUS
Fluid Cleanliness - ISO 18-16-13 is recommended
Operating Temperature - Operating temperature is determined by the viscosity characteristics of the fluid used. Control operating temperature as needed to assure that fluid viscosity is within acceptable limits. Because high temperatures degrade seals, reduce the service life of the fluid, and create scalding hazards, fluid temperatures should not exceed 180° F. (82° C.) at the case drain.
Mounting Position - Unrestricted. However, horizontal mounting is preferred.
Relief valves are recommended for all applications to help protect personnel and the system from potentially damaging overloads
|
|
THE OMEGA N PUMPS
Compact high pressure reciprocating piston pump, for reduced investment costs but manufactured according to highest Cryomec standards:
Available flow rates: 1 to 70 L/min
Pressure up to 400 bar
Available for all cryogenic gases including LNG
Low operation cost
Large scale of feature with numerous options
|
|
|
AccuStream intensifier waterjet machines give you a choice of 30-, 50-, 75- 100- or 150-horsepower units with adjustable pressures up to 60,000 psi. All AccuStream waterjet machines feature the AccuStream-built AIT Technology for maximum cut pressures and peak performance under the most demanding applications.
|
|
|
|
|
|
The direct drive pump operates in the same manner as a low-pressure "pressure washer" that you may have used to pressure wash a house or deck prior to repainting. It is a triplex pump that gets the movement of the three plungers directly from the electric motor. These pumps are gaining acceptance in the waterjet industry due to their simplicity. At the time of this writing, direct drive pumps can deliver a maximum continuous operating pressure 10 to 25% lower than intensifier pumps units (20k to 50k for direct drive, 40k to 60k for intensifiers).
Only Flow manufactures both HyPlexTM and intensifier pumps. As a result, we can offer you the pump solution that is best suited for your application. Whether you run 24 hour, 7 days a week production or prototype jobs only a few hours a day, we have the right pump for you. Best of all, no matter which style of pump you choose, you'll receive a Flow pump that is reliable, simple, efficient, and easy to maintain. The focus of all our designs is performance, reliability and longevity so that your productivity is increased.
Flow Pumps Operate At Higher Pressures
Flow intensifier pumps are rated at 60,000 psi and our systems actually run at that pressure. No backing off, no hedging. It's another big reason why Flow equipment out-produces all others. Flow manufacturers the most complete range of ultrahigh-pressure waterjet pumps in the industry. From 205 hp, 6.5 gpm diesel powered Husky pumps for surface preparation to 100,000 psi pumps used for ultrahigh-pressure food processing to intensifier and direct drive pumps for waterjet cutting, Flow has a pump to meet your needs. Flow is the only waterjet company to offer its customers a choice of intensifier or HyPlex(direct drive) waterjet cutting pump technology. The wide range of waterjet pumps Flow builds is your assurance that you and your application will be paired with a pump that is specifically tailored to meet your needs.
Our waterjet cutting pumps set the industry standard for performance and reliability that is proven in 24 hour, 365 day a year operations around the world. All Flow pumps are capable of smooth, continuous operation, year after year, at the pressure they are rated. This ensures you receive the maximum possible benefit of pump's capacity and the performance you have paid for. It's an important distinction to make, because a pump's performance is limited by the lowest pressure it reaches in a cycle. By operating smoothly with a minimum of pressure fluctuations at the highest rated pressure a Flow pump can outperform other pumps which are rated for high pressures, but don't necessarily operate there smoothly or continually.
|
|
|
CAT PUMPS specializes in portable FOAM FIREFIGHTING SYSTEMS for fast knockdown of brush and grass wildfires. Our FOAM FIREFIGHTING SYSTEMS feature a special foam gun delivering metered foam to smother the flames along with a high pressure spray to soak and deep penetrate the ground to keep fires from re-igniting. Ultra compact units are available from 4-18 HP. These units are designed for easy mount onto ATV's, pickup trucks and utility vehicles. Call for a custom quote.
|
|
|
Our CORROSION-RESISTANT STAINLESS STEEL PUMPS are the pump of choice for sea water reverse osmosis desalination, chemical injection, wastewater re-injection, DI water gas turbine misting, oil processing and CO2. Cast and Block-Style 316SS manifolds and Duplex alloy liquid-end construction provide strength and compatibility. Special flushed models permit an external flush for lubricating with low lubricity liquids and cooling with high temperature liquids. Coordinating stainless steel system accessories provide system pressure setting and overpressure protection. CORROSION-RESISTANT STAINLESS STEEL PUMPS or custom pumping systems are available from .5 GPM to 240 GPM. Request a quote.
|
|
KD716 is a serial pump in sturdy design for low viscous liquids, available in various drive and liquid end configurations.
Options
- special lubrication for inclined pump installation
- integrated water/oil cooler
- integrated gear box for direct drive
- noise hood for power end
- suction valve release for by-pass operation
- pressure gauge connection on discharge side
- suction pulsation damper
|
|
Wright Flow Technologies proudly introduces its latest innovation in Positive Displacement Pumps for the Sanitary and Industrial Markets, the new RevolutionTM the first true CIP (Clean in Place) Hybrid Circumferential Piston & Lobe Pump.
The RevolutionTM merges the benefits of Lobe & Circumferential Piston technologies into one platform. This new platform delivers:
* Increased product yield
* Increased lifetime of components
* Reduced maintenance costs
* Outstanding CIP cleanability and higher standards of hygiene.
|
|
URACA high pressure and ultra high pressure plunger pumps are outstanding in their compact design and flexible applications. Based on the industrial process pump design, the pumps are relatively unsusceptible to small particles in the tap water, even at high pressures.
Options
- Flanged housing for hydraulic drives ISO 125 / ISO 140
- Drain device
- Suction and discharge connections, optionally on left or right-hand side
- position of drive, optionally on left or right-hand side
- special designs: hot water, stainless steel, solvents
- stuffing box cooling / flushing is possible with power end cooling
- pump unit with electric or diesel drive
- pump unit suitable for pressure tests with ATEX certificate
|
|
Ideal for use in remote and/or mobile locations where electricity is scarce, the iP55-280DS is powered by a 280hp Cummins turbo diesel engine that meets Tier 3 emissions standards. It is capable of producing a flow rate of up to 4.1 gallons (15.5 liters) per minute of 55,000 psi (3,000 bar) ultra-high pressure water for waterjet cutting, surface preparation and cleaning applications.
The iP55-280DS utilizes a pressure-compensated hydraulic system to drive dual plunger-style intensifiers. The use of hydraulic fluid power provides smooth flowing UHP water resulting in long system life. Reliable and precise control of the electronically shifted intensifiers ensures superior performance standards with reduced operating costs. The pump is built on a skid-mounted frame with lifting eyes and forklift guides provided for increased mobility.
A 36,000psi model is also available.
Find out more at www.jetedge.com.
|
|
|
|
|
|
|
CAT PUMPS offers an extensive line of TRIPLEX, POSITIVE DISPLACEMENT, LIQUID HANDLING PUMPS rated from .5 to 240 GPM. Our pumps provide both high flows and high pressures up to 10,000 PSI. Liquid-end construction is available in brass, NAB, 316SS or Duplex alloy liquid-end for liquid compatibility. Our TRIPLEX PLUNGER PUMPS handle a wide variety of liquids including sea water, DI water, reclaim water, chemicals, oils, CO2, machining coolants, sanitizers, fertilizers and pesticides. Quality features like heavy-duty crankshafts, high-strength connecting rods, dual bearings, forged brass or machined stainless steel manifold heads, exclusive, unique seal design and concentric solid ceramic plungers provide exceptional life and low maintenance. Our close tolerances and 90% mechanical efficiency provide low energy consumption for high returns on your investment. Custom flushed pumps permit an external flush liquid for added lubrication with low lubricity liquids such as DI water and cooling when pumping high temperature liquids. Select models are ATEX 2 and 3 certified. Request a pump our custom pumping system quote.
|
|
P3-80 is a maintenance friendly triplex plunger pump which is manufactured in series. Nearly all components are standardized.
- Power max. 750 kW
- Pressure max. 1,020 bar
- Capacity max. 3,295 l/min at 130 bar
|
|
Together with our standard stainless steel materials matching, we can offer special stainless steels, titanium or bronze.
Temperature ranges up to 350 degrees C. e.g. pumps for thermo oils.
High capacity - external gear pump
Gear dosing pump Stainless steel gear dosing pump in special design
HP radial piston pump (closed design)
High capacity internal gear pumps with integral pressure limiting valve for low noise operation
|
|
High Pressure Pump Series HDP 485
Features
- Power ratings up to 450 kW
- Vertical 3 cylinder design
- Wide variety of complementary ancillaries
technical data
- Rod force: 200 kN
- Stroke:100 mm
- Mean piston speed at n2; 315 r.p.m. = 1,06 m/sec; 380 r.p.m. = 1,27 m/sec; 445 r.p.m. = 1,48 m/sec; 465 r.p.m. = 1,54 m/sec
|
|
HDP 25 High Pressure Pump Series
Features
- Power ratings up to 30 kW
- Vertical 3 cylinder design
- Wide variety of complementary ancillaries
technical data
- Rod force: 17,6 kN
- Stroke: 30 mm
- Mean piston speed at n2; 625 r.p.m. = 0,63 m/sec; 750 r.p.m. = 0,75 m/sec; 900 r.p.m. = 0,90 m/sec
|
|
FORDIA’s Elepumps are the best light-weight, high pressure plungers in the industry.
ELEPUMP KF
The Elepump KF is a heavy-duty high pressure water pump designed for high-demand drilling. Its triplex water plungers offers up to 45 gallons per minute. The new design of the pump features new frame design for increased life expectancy; stainless steel manifold; and new leakage free seal design. The result is a pump that promises long life, minimal down time, and greatly reduced operating costs,
Designed for simple maintenance, Elepump KF requires only periodic oil checks and changes - and worn parts can be replaced quickly and simply without special tools.
|
|
The Hypro 2535S triplex plunger pump is designed for durability, top performance, and convenient servicing. It achieves up to 38 gpm (144 lpm) and 1200 psi (83 bar). The 316 stainless steel two-piece manifold minimizes washout and corrosion. A strong power end including oversized crankshaft, bearings, and connecting rods easily handles abuse caused by start-up and intermittent operation.
Backed by the best warranty in the industry, Hypro pumps are designed for, and not adapted to, the car wash industry, resulting in pumps that deliver higher pressure and increased reliability.
|
|
|
WOMA designs, produces and sells high-pressure plunger pumps driven by electric motors or combustion engines. The can be run in stationary mode but are also suitable for mobile use. The pumps have power ratings up to 780 kW, operating pressures up to 3000 bar, and volumetric flow rates up to 1679 l/min.
|
|
GENERAL SPECIFICATIONS
/- 1% Steady State Accuracy over a 10:1 Turndown (w/constant speed drive)
Continuous Duty / Severe Service Design
Polar Crank Drive Design
Rugged Cast Iron Gear Housing
Modular Design
Multiplex Capability
Variable Stroke Length (non-last motion)
Integral Pressure Lubrication System
Double Ball Check Valves
Pressures up to 10,000 psig (690 bar g)
Flows up to 1,225 gph (4,637 lph)
Meets API Standard 675
|
|
|
|
|
|
Piston pumps are precise and – compared to diaphragm dosing pumps – almost pressure-independent metering units. The flow rate changes in proportion to the stroke length and can thus be adjusted to very small values. Fields of application are – among others – process engineering and chemical processes, i.e.: wherever the medium must be metered precisely.
The FEDOS E / DX piston dosing pumps from Lutz-Jesco are available at flow rates between 0.17 and 31.5 l/h, with or without microprocessor control. Depending on the size of the pump, maximum pressures between 30 and 200 bar are admissible.
If no control is required for constant metering, the motor is connected directly to the terminal box. In this case, FEDOS E pumps are used. To change the flow rate, either the stroke length can be adjusted mechanically, or the speed of the motor is controlled by means of a separate frequency converter.
FEDOS DX pumps are used if an integration in controls or automatic control systems is requested.
FEDOS DX pumps allow the adaption to a large number of different control systems and system monitoring equipment. The signals required for the external avtivation of the pump can be simple voltage-free closing contacts from water meters or controllers or analog 0(4)...20 mA signals.
|
|
|
Self-serve carwash and tunnel prep unit owners across the country are making the switch to Hypro’s 2300 Series plunger pumps. Backed by the best warranty in the industry, Hypro pumps are designed for, and not adapted to, the car wash industry, resulting in pumps that deliver higher pressure and increased reliability.
|
|
The Resato Powerjet PJE waterjet cutting pump is an example of our continuing commitment to research and development.
The latest generation of our skillfully designed waterjet cutting pumps offers monitor control and simple time-saving servicing possibilities. Proven reliability reduces down-time to a minimum and the operation costs will be reduced accordingly. As a result of further developments and tests in our cutting laboratory, the life cycle of high pressure seals and other parts subject to wear has been extended considerably.
To complement our extensive range of waterjet cutting pumps we offer all waterjet cutting accessories vital to the realization of a turn-key cutting system.
|
|
The Hypro 2535S triplex plunger pump is designed for durability, top performance, and convenient servicing. It achieves up to 38 gpm (144 lpm) and 1200 psi (83 bar). The 316 stainless steel two-piece manifold minimizes washout and corrosion. A strong power end including oversized crankshaft, bearings, and connecting rods easily handles abuse caused by start-up and intermittent operation.
Performance Information
- Max. flow: 38 gpm/144 lpm
- Max. pressure: 1200 psi/83 bar
- Max. rated speed: 800 rpm
|
|
TRIPLEX PLUNGER PUMPS with stuffing box and permanent washing of the plungers.
The pumps are suitable for pumping liquids with different density or kind.
Characteristics:
- gears and shafts in high-resistance steel
- steel plungers hard chromium plated
- pump casing in special cast iron
- ball valves and cap valves
- special sealing gaskets for plunger and stuffing box
|
|
Trido pumps are injection pumps with three simple effect pistons. They are compact, robust, and easy to maintain.
Use
They are designed to transfer or to inject water, drilling mud, or light slurries. They can be mounted on drilling rigs with a hydraulic motor. They also can be mounted on a frame with a diesel engine or an electric motor.
Versatility
The pumps on a frame are equipped with a handling hook. Performance The cylinder liners and the ball valves are made in treated steel. These spare parts are easily replaced. All pumps are lubricated in an oil bath. All pumps are equipped with a safety valve in order to protect the pump in case of a blocked exhaust pipe.
Safety
All moving parts are equipped with a safety cage. All pumps are equipped with an
emergency stop.
|
|
Flow rate is based on 100% volumetric efficiency and 20°C ambient temperature
min. inlet pressure depending on fluid medium
min. rpm depending on rod loading
Gear with force-fed lubrication (> 160 kw with oil cooler)
Standard gear ratios:i = 3,33 - 3,50 - 4,04 - 4,62 - 5,44
Also available to API 674
Special medium such as sea water, glycol, methanol, oils, etc. on request
|
|
Pulseless series is designed to be almost nothing of any pulsation with high accuracy by special cam and check valves.
Compact design achieved by the cylindrical cam which drives two plungers.
|
|
|
|
