|
|
Mini linear piston block-compressor not lubricated.
- Nominal capacity: 5 to 50 l/min,
- Maximum Pressure: 0,1 to 2,5 bar.
|
|
|
|
|
|
The EcoDry M incorporates a dry sliding mechanism without the need for oil or hydrocarbons.
Through the further developed and optimised compression processes, the EcoDry M 15/30 attains with three compression stages a base pressure (total) in the low 10-2 mbar range.
Since the EcoDry M 15/20/30 may be operated either vertically (as normally delivered) or horizontally, this pump is highly flexible when it has to be integrated into the customer’s system.
Advantages to the User
Low maintenance, free of oil and bearing lubrication, free of hydrocarbons
Extremely low particle emissions on the intake and exhaust sides
Rugged and most reliable
Low power consumption
Service friendly
Air cooling
Plug & play
Good pumping speed at low base pressure
High water vapour tolerance (gas ballast standard)
No grease lubricated bearings in the vacuum section
Leak tight
Compact size
Runs at 1000/1200 rpm (50/60 Hz mains)
Rugged full cross section exhaust valves
For both horizontal and vertical operation
Typical Applications
Applications in physics
Loadlock chambers
Transfer chambers
Mass spectrometers
Electron microscopes
Lighting
Thinfilm coaters
Freeze drying
Forevacuum pump for dry high-vacuum systems
Pumping of oxygen concentrations over 21 percent by volume upon request
|
|
|
|
|
|
Advantages to the User
Gas ballast facility
Easy maintenance
Good ultimate pressure with and without gas ballast
High pumping speed at low intake pressures
Compact design with flange mounted motor
High water vapor tolerance
Reliable continuous operation
Tolerant and rugged, due to non-contact rotary piston within the pump chamber
Very smooth operation due to dynamically balanced masses
Separate oil filling for the gear protects the gear against contaminated pump oil
Oil is used for sealing, lubrication and cooling
A built-in anti-reverse lock prevents incorrect rotation of the piston and also stops it being pulled back when the pump is switched off while under vacuum
Air cooling makes the pump environmentally- friendly and economic
Clear design and service-friendly due to the modular design
Typical Applications
Chemical, metallurgical and electronic vacuum processes
Impregnating, degassing and drying process-es in experimentation systems, in drying cabinets, extrusion etc.
Pressure range down to 4 x 10 E-2 mbar (2.4 x 10-2 Torr) without gas ballast or to 5 x 10 E-1 mbar (3 x 10 E-1 Torr) with gas ballast
Backing pump for Roots vacuum pumps at intake pressure down to 10 E-3 mbar (0.75 x 10 E-3 Torr)
Supplied Equipment
With DN 65 DIN flanges on the intake and exhaust sides for direct connection of DN 63 ISO-K flange components
Ready for operation, complete with oil filling
Special models for different motor voltages, motor frequencies and other protection class ratings are available - Details on these upon request
|
|
|
|
|
|
Engineered for compactness, economy and dependability- Ingersoll-Rand's Vacuum pumps are the number one choice for demanding applications, providing top operating efficiency combined with low maintenance. And best of all, these vacuum pumps are backed by Ingersoll-Rand, the world's leader in air compressor and pump manufacturing.
Features:
.Cast Iron Construction:
Cylinders and frame are designed with 100% cast iron for durability and long life.
.Cylinders:
Separately cast cylinders with deep fins allow for 360° cooling, removing the heat of compression. Individual bolting of the cylinders to the frame for easy inspection and maintenance.
.Low Oil Level Protection:
The low oil level switch protects the pump from operating without proper lubrication.
.Piston Rings:
Each piston is equipped with (2) compression rings and (2) oil control rings to maintain maximum operating efficiency and low oil carryover.
.Valves:
Stainless steel valves are readily accessible and inexpensively replaced if necessary.
.Connecting Rods:
One piece design permits precision aligned machining of both crankpin and piston pin bearings resulting in longer bearing life. Also allows for simple maintenance-no bolts to come loose or adjust.
|
|
|
Kinney KC & KTC Series Multi-stage rotary piston vacuum pumps provide pumping speeds of 5-112 CFM (8-190 m³/h) with ultimate pressures of 0.2 milliTorr (0.027 Pa). Our KTC series vacuum pumps include our exclusive triplex piston design to eliminate vibration.
|
|
|
KINNEY rotary piston vacuum pumps provide vacuum levels to 0.2 milliTorr (0.027 Pa) with long operating life. Our triplex piston designs are inherently balanced to eliminate vibration.
|
|
|
|
|
|
General descriptino
HINDHIVAC manufactures different models of Rotary Piston Vacuum Pumps. These Rotary Piston Vacuum Pumps are robust and are most reliable. They can be used in combination with Roots Vacuum Blowers.
These Piston Pumps are extremely useful in handling high volumes of gases and are provided with Gas Ballast Valves to pump out condensable vapors. These piston pumps are built to give uninterrupted service even under strenuous working conditions with economical power and oil consumption.
These Piston Pumps are water cooled to ensure continuous duty with high efficiency. The Piston Pump has a unique design in which the pump ensures that while the piston continues to rotate it maintains isolation of the compression and the suction cycle, drawing out the compressed air through the exhaust valve. The pump has a low oil charge and the gas ballast is provided to avoid oil contamination due to condensable vapors. This Piston Pump is water cooled to avoid over heating and for continuous running
|
|
| ... products without technical information |
| |
|
|
|
|
The series WA/WAU Roots vacuum pumps are provided with directly flange-mounted air-cooled standard three-phase motors. The oiled radial sealing rings of the RUVAC WA/WAU for sealing the shaft against the atmosphere are made of FPM (fluor caoutchouc).
The WS/WSU series pumps are driven by air or water-cooled canned motors.
Roots vacuum pumps of the series WAU/WSU are provided with an additional integrated pressure equalization line and a differential pressure valve.
Pumps from these series are supplied with a vertical pumping action as standard.
Advantages to the User
Two air-cooled series, each with four models
Reliable and trouble-free
Sealing rings with their housing can be readily replaced
Shaft seals and elastomer seals made of FPM/Viton
Air-cooled standard motors in accordance with IEC dimensions eg. NEMA dimensions
Easy to exchange with custom motors
Integrated pressure equalization line for protection against overloading at high pressures
Pumping direction may be changed as required
ATEX versions compliant to 94/9/EC possible
Typical Applications
For oil-free compression of gases and vapors in combination with a backing pump
Short cycle pumping processes also in the presence of large quantities of gas and vapor
Supplied Equipment
RUVAC WA/WAU are supplied as standard for a vertical pumping action, horizontal pumping action upon request
Mineral oil N 62 is used as standard
Gasket in the intake flange with dirt sieve
The required oil filling is included in separate bottles
|
|
|
Pedro Gil, S.L. is a manufacturer company for pressure and vacuum groups, root pumps and vacuum systems.
|
|
|
|
|
|
C-KLR ZEPHYR
Volume flow: 80 - 140 m³/h
Overpressure: +1.0 bar
Vacuum: -0.6 bar
With the innovative, dry-running C-KLR ZEPHYR multi-claw range from Elmo Rietschle, pressure and vacuum can be combined in a single claw stage. All operation points on pressure and suction side work almost independently from each other. The C-KLR ZEPHYR operates economically and highly efficiently thanks to the patented triplelobe design with intermediate charging of air. This new design reduces pulsation in the pipes connected to the pump, and keeps the noise level low. An integrated cooling system for compressed air allows operation in applications, where compressed air
temperatures are of importance.
Advantages:
- High efficiency, dry and frictionless compression
- Low maintenance
- Integrated air cooling without additional cooling medium
- Suitable for multiple applications
This series is also available as vacuum pump (C-VLR ZEPHYR) and compressor (C-DLR ZEPHYR).
Typical Applications:
Printing & Paper, Chemical, Environmental, Packaging, Pneumatic Conveying, Woodworking
|
|
The Mink rotary claw pumps were developed especially for use in industrial applications where constant vacuum or pressure is required, along with totally oil free compression. Mink vacuum pumps or blowers are used in all applications, which require oil-free vacuum or oil-free compressed air.
The Mink is available as a single-stage or two-stage vacuum pump.
Features
* Non-contact operation
* No maintenance
* High efficiency
* Many different sizes and models
* Speed control (option) · ATEX certified (option)
* Version for oxygen delivery
Application
Ideal for use in various industries such as Plastics, Printing and Paper, Food, Beverage, Wood, Pneumatic Conveying, Brick Making, Adsorption and Degassing, Environmental Technology, Metallurgy, Remediation and many more.
|
|
The Power Pump Portfolio.
Roots pumps for Every Low and Medium Vacuum Applications.
Our Roots pumps offer pumping speeds ranging from 250 to 25,000 m3/h. They can be safely employed for low and medium vacuum applications in the coating or semiconductor industry, in research & development, metallurgy or in chemistry and process technology.
The gear and bearing chambers in our Roots pumps are completely separate from the gas pumping chamber. Because the rotors operate without making contact, dry, hydrocarbon-free operation is assured.
A further advantage: Thanks to air cooling, operating costs are significantly lower than with water cooling. The design principle of our proven Roots pumps has also been expanded to include magnetic couplings. These hermetically sealed pumps make oil leaks a thing of the past. We have also developed special pumps for processes that take place in explosive environments or for evacuating explosive gases.
|
|
The HenaLine™ Innovation.
A Complete Line of Single-Stage Rotary Vane Pumps for Low and Medium Vacuum Applications.
We now offer you a complete line of new single-stage rotary vane pumps for all low and medium vacuum applications. These pumps offer pumping speeds of between 25 and 1,000 m3/h. Whether as a stand-alone pump or as a backing pump for our OktaLine™ in connection with medium vacuum applications: HenaLine™ means top quality at all times.
Their reliability, performance and compact size round out the outstanding features of the HenaLine™ pumps. Moreover, the principle of operation of the HenaLine™ pumps assures low operating temperatures.
And last but not least!
Oil mist separator, oil return and safety valves are integrated as standard equipment in this line of pumps. Moreover, the gas ballast valve assures pump-down of steam and other process vapors. In every respect, HenaLine™ simply shines!
|
|
|
Electric and Compressed Air Powered Vacuum Pumps, Vacuum Generators and Vacuum Stations, Vacuum Valves and Switches, Vacuum Filters and Exhaust Mufflers, Air Movers and Transfer Tubes, and a wide range of Vacuum System Accessories, all available at competitive prices.
|
|
Theis is most significant model base on the multi stage principle Low compressed air are required far massive evacuation volumes at high vacuum flow and high vacuum level rate. V-tec air saving kit is available in this pump in order to maximum reduce the energy usage. VITON & EPDM seals can be also stipulated as option.
|
|
The Kavac series of vacuum products includes a wide variety of conventional vacuum components, as well as more specialised items such as variable vacuum pumps, material transfer and air amplification units. KV's vacuum division is also able to deliver customer-specific vacuum solutions; often developing customised pumps or completely integrated vacuum control systems. A comprehensive range of vacuum cups complements the Kavac range.
|
|
* Large vacuum flows
* Short evacuation time
* Good for handling porous materials or if leakage is present
* Energy-Saving (ES) available
* Available with connection plate in aluminium (AD) and composite PPS (D).
|
|
Compact ejectors Schmalz X-Pump SXP / SXMP
Application areas :
The new generation of vacuum compact ejectors for the special tasks of the automotive sector and for use in automated vacuum systems in the sheet-metal and plastics industries.
|
|
The first ISO venturi.
The V2i is a multi-function vacuum generator with straight through design and electrical ISO 15407-1 valve for on/off and blow off control.
The valve directly mounted on the vacuum generator brings a reliable and efficient solution for all robotics applications wherever short cycle time is required.
Non-clogging V2i, that's the solution for difficult applications.
|
|
Based on the Venturi tube principle with adjustable sections
Characterised by the possibility of adjusting the volumetric suction capacity and vacuum level simply by turning the Venturi tube outlet section.
Applied for the suction and transport of products of low specific weight and also liquids like exhausted oil or oil coolants. They can also be used for suction in suckers in contact with particularly powdery and friable products, avoiding the use of vacuum pumps with easily clogged filters
Maintenance free, good filtering of the compressed air supply is recommended
Maximum vacuum level: 550 mmHg (75% vacuum)
|
|
|
|
|
|
C-KLR ZEPHYR
Volume flow: 80 - 140 m³/h
Overpressure: +1.0 bar
Vacuum: -0.6 bar
With the innovative, dry-running C-KLR ZEPHYR multi-claw range from Elmo Rietschle, pressure and vacuum can be combined in a single claw stage. All operation points on pressure and suction side work almost independently from each other. The C-KLR ZEPHYR operates economically and highly efficiently thanks to the patented triplelobe design with intermediate charging of air. This new design reduces pulsation in the pipes connected to the pump, and keeps the noise level low. An integrated cooling system for compressed air allows operation in applications, where compressed air
temperatures are of importance.
Advantages:
- High efficiency, dry and frictionless compression
- Low maintenance
- Integrated air cooling without additional cooling medium
- Suitable for multiple applications
This series is also available as vacuum pump (C-VLR ZEPHYR) and compressor (C-DLR ZEPHYR).
Typical Applications:
Printing & Paper, Chemical, Environmental, Packaging, Pneumatic Conveying, Woodworking
|
|
The Mink rotary claw pumps were developed especially for use in industrial applications where constant vacuum or pressure is required, along with totally oil free compression. Mink vacuum pumps or blowers are used in all applications, which require oil-free vacuum or oil-free compressed air.
The Mink is available as a single-stage or two-stage vacuum pump.
Features
* Non-contact operation
* No maintenance
* High efficiency
* Many different sizes and models
* Speed control (option) · ATEX certified (option)
* Version for oxygen delivery
Application
Ideal for use in various industries such as Plastics, Printing and Paper, Food, Beverage, Wood, Pneumatic Conveying, Brick Making, Adsorption and Degassing, Environmental Technology, Metallurgy, Remediation and many more.
|
|
V-VSI TWISTER
Suction capacity: 100 to 360 m3/h
Vacuum: < 0.1 mbar (abs.)
Screw vacuum pumps are easy to service and durable. They also excel when it comes to high vapor and water tolerance. Noise and vibration levels are remarkably low.
The innovative screw profile not only delivers high efficiency and an end vacuum of less than 0.1 mbar (abs.) but also maximum volume flow at high vacuum.
Advantages:
• Progressive graduation of screw pitch
• Low noise level
• Low temperatures
• Easy to service
• Variable speed available
• Dry, contact free operation
• Oil free exhaust air
• No wear inside compression chamber
• Only service needed is oil change in gearbox and bearings
• Sealing gas is optional
Typical Applications:
Ppackaging, Drying, Coating, Vacuum furnaces and Solar cell manufacturing
|
|
|
Kinney SDV Dry Screw vacuum pumps operate without any sealing liquid in the pumping chamber. Without metal-to-metal contact inside the pumping chamber, wear is greatly reduced.
|
|
This unit is able to fulfil the highest requirements for a wide range of applications. By entering the load and output into your customer system, the air supply system automatically and directly adapts to the given requirements. The frequency-controlled drive unit offers a wide control range with optimised demand matching. In addition to energy savings and higher efficiency, this also results in lower maintenance requirements. The non-contact, oil-free screw unit ensures high air flows with low pulsation and lends itself to "master/slave" operation. Integrated accessories include a non-return valve, intake filter, sound absorbers and ventilation/bleed system. An air blast cooler is also available.
|
|
|
|
see the results for the following category : 
