|
|
Wherever fluids are pumped, compressed or stirred, it is the bearings and face seal rings that concern design engineers in particular. The type of material used for these parts has a vast impact on operational reliability and durability, especially when critical media are involved.
|
|
SSIC Ceramic Bearings can be used with a standard DST permanent magnet coupling directly in the process fluid - for example in a centrifugal pump.
SSIC Ceramic Bearings are produced using new material combinations and modern manufacturing techniques such as laser technology.
The complete temperature range up to 350°C (660°F) is covered with a single bearing design.
Please note that SSIC Ceramic Bearings have no dry running properties. |
|
| ... products without technical information |
| |
The most important fields of application for the lasered, stamped, green-scored, dry-pressed and, depending on application, the metalized version of our substrates for passive components are:
Chip resistors, resistor networks, potentiometers |
|
CeramTec is one of the leading manufacturers internationally of metallized substrates on an aluminum oxide (Rubalit®) and aluminum nitride (Alunit®) basis.
The pastes developed by CeramTec are characterized by high adhesive strength, good flux and excellent stability in solder baths.
The metallizing systems developed by CeramTec enable superior adhesion, high wettability, and excellent performance consistency in soldering baths.
|
|
XLBearings good at manufacturing ceramic bearings and hybrid ceramic bearings, rings is made by Si3N4 or ZrO2, cage is made by PTFE, PEEK, Nylon, Brass and so on, 6000 series, 6200 series, 6300 series, 7000 series, 7200 series, 51000 series, 1200 series, we can manufacture ceramic bearings according to clients drawing or samples or technology information.
Tel:+86-574-8750-3999
Fax:+86-574-8750-2619
E-mail: info@xlbearings.com
|
|
CeramTec is one of the leading manufacturers internationally of metallized substrates on an aluminum oxide (Rubalit®) and aluminum nitride (Alunit®) basis.
The pastes developed by CeramTec are characterized by high adhesive strength, good flux and excellent stability in solder baths.
The metallizing systems developed by CeramTec enable superior adhesion, high wettability, and excellent performance consistency in soldering baths.
|
|
ULTRAMIC™ 600 Advanced Ceramic Heater
When you need a lot of power in a small package, the ULTRAMIC™ 600 puts the performance of advanced ceramics to work for you. Constructed of aluminum nitride (AlN), the ULTRAMIC 600 can operate up to 600°C (1112°F) and deliver ultra-fast ramping of up to 150°C (270°F) per second for rapid thermal cycling applications.
The robust mechanical structure of the high density AlN enable these heaters to exhibit exceptional mechanical stability throughout the temperature range. This makes the product especially suitable in applications where consistent part-to-part thermal contact during heating cycles is critical. Additionally, these heaters are applicable when requiring a clean, non-contaminating heat source as they are particle free, impervious to moisture and resistant to acidic attack.
Applications:
Semiconductor wire and die bonding
Analytical instrumentation
Medical devices
Packaging
Aerospace |
|
Infrared SUNRAD Emitters is suitable for great radiant efficiency, thanks to the very high temperature of its emitting surface (900°C) and to its small dimensions.
SUNRAD emitters can be installed at considerable height (up to 30 m) considering they are provided with a reflector concentrating the radiation power.
Sempre più diffuso per il riscaldamento dei luoghi di culto |
|
A RANGE OF CERAMIC GAS HEATERS ADAPTED TO ALL HEATING NEEDS IN INDUSTRIAL BUILDINGS (height of 4 meters and more).
Use: Industrial buildings, Churches, Sports halls, Car service, Terraces, ...
- a large range of heaters from 2,5 to 27 kW and more.
- a choice of 10 powers for a comfort in all type of buildings whatever the
hanging height of the heaters
- a double-speed option for a better comfort, particularly in well insulated
buildings |
|
| The DK Series is a line of 14 ceramic heaters in capacities from 30,000 to 160,000 Btu/hr, four in propane gas and ten in natural gas. Suitable for horizontal mounting or angled up to 35°, this series can meet a variety of spot and area heating requirements. |
|
U.L. Recognized - E56973 C.S.A. Certified - 016386-0-000
Applications:
Copiers, Dehumidifiers, Glue Guns, Heat Sealing Tools, Instrumentation, Resisters, Soldering and Desoldering Equipment, Valve Heaters.
Features:
-The Hotwatt Ceramic Heater is a ceramic body encasing a resistance element and packed within magnesium oxide.
-The heaters are terminated with flexible insulated lead wires.
-Temperatures to 1300°F (705°C)
Construction:
-Ceramic body
-Premium grade resistance wire element
-Magnesium oxide packing
-Ceramic end seal
-Flexible insulated lead wires |
|
| ... products without technical information |
| |
Ceramic fiber heaters intergrate a high temperature iron-chrome-aluminum (ICA) heating element wire with ceramic fiber insulation. Numerous stock, standard and/or custom shapes can be provided, achieving the "heated insulation" concept for your high temperature, non-contact applications. The ceramic fiber insulation isolates the high temperatures inside the heated chamber from the outside. The heaters are low mass, fast heating, with high insulation values and self-supported heating elements that offer some of the highest temperature heating capabilities within the Watlow family of heater designs.
Applications
High temperature furnaces
Metal melting, holding and transfer
Semiconductor processing
Glass, ceramic and wire processing
Analytical instrumentation
Fluidized beds
Laboratory and R&D
Other high temperature process applications |
|
ULTRAMIC™ 600 Advanced Ceramic Heater
When you need a lot of power in a small package, the ULTRAMIC™ 600 puts the performance of advanced ceramics to work for you. Constructed of aluminum nitride (AlN), the ULTRAMIC 600 can operate up to 600°C (1112°F) and deliver ultra-fast ramping of up to 150°C (270°F) per second for rapid thermal cycling applications.
The robust mechanical structure of the high density AlN enable these heaters to exhibit exceptional mechanical stability throughout the temperature range. This makes the product especially suitable in applications where consistent part-to-part thermal contact during heating cycles is critical. Additionally, these heaters are applicable when requiring a clean, non-contaminating heat source as they are particle free, impervious to moisture and resistant to acidic attack.
Applications:
Semiconductor wire and die bonding
Analytical instrumentation
Medical devices
Packaging
Aerospace |
|
Fiber Insulated Heater Type FIH combines a heat source with superior high temperature insulation - an ideal solution for many industrial heating applications. These heaters deliver fast, efficient and reliable uniform heat to temperatures of 1100°C (2012°F). Designed to deliver power densities up to 1500 watts/ft2, FIH is one of the most versatile embedded element radiant heaters produced. OEM furnace and thermal process equipment manufacturers plus end users alike have embraced this combination heating and insulating system.
ZIRCAR Flat Panel, Full Cylinder and Semi-Cylinder Fiber Insulated Heaters Type FIH consist of high quality helically-wound Fe-Cr-Al alloy resistance wire elements embedded in a rigid body of vacuum formed high temperature refractory fiber. The lightweight ceramic fiber insulation has very low thermal mass and thermal conductivity and thus can handle extremely rapid cycling. Elements are typically mounted flush with the heated surface. The diameter of the helically wound element coil is kept to a minimum, reducing the difference between the element and chamber temperature, thus ensuring long heater life, and enabling the design and manufacture of extremely responsive heating systems.
All ZIRCAR Fiber Insulated Heaters are 100% organic free and will not smoke or outgas when heated. ZIRCAR Fiber Insulated Heaters are available in flat panel, full cylinder and semi-cylinder shapes - with several lead styles. |
|
U.L. Recognized - E56973 C.S.A. Certified - 016386-0-000
Applications:
Copiers, Dehumidifiers, Glue Guns, Heat Sealing Tools, Instrumentation, Resisters, Soldering and Desoldering Equipment, Valve Heaters.
Features:
-The Hotwatt Ceramic Heater is a ceramic body encasing a resistance element and packed within magnesium oxide.
-The heaters are terminated with flexible insulated lead wires.
-Temperatures to 1300°F (705°C)
Construction:
-Ceramic body
-Premium grade resistance wire element
-Magnesium oxide packing
-Ceramic end seal
-Flexible insulated lead wires |
|
The original Ceramic Stone is used for fine detail polishing. The Ceramic Stone is extremely strong and thin for tight ribs and slots. The Ceramic Stone is excellent stone for EDM removal.
Our Ceramic Stones are offered in approximate grit sizes of:
100 - Green
120 - Gold
180 - Light Brown
220 - Orange
320 - Brown/Black
400 - Blue
800 - White
1000 - Red |
|
Innovative stones for polishing narrow areas, such as ribs, bosses, etc. of die and mold. No clogging, no chipping, no cracking and easy to shape. This tool enables efficient polishing and uniformed finishing, especially with ultrasonic polisher. Also suitable for removing EDM scales.
|
|
| Whether fused or sintered, our ceramic beads ensure high efficiency when microgrinding and microdispersing a whole range of industrial products such as paints, inks, pigments, dyes, mineral fillers, magnetic coatings, pharmaceuticals, agrochemicals and cosmetics. |
|
| ... products without technical information |
| |
| CoorsTek offers a wide variety of long-life, heat-stable, and corrosion-resistant ceramic hard-face seals using high-grade aluminas, silicon carbide, tungsten carbide, carbon graphite, and specialty polymers. |
|
Alumina ceramics:
AI2O3-99% AI2O3-97%
Purigy--------------------% „99.5 „97.0
Density-------------------g/cm3 3.89 3.71
Hardness Vickers1kg-------Kg/mm2 2000 1900
Modulus of Elasticity-----GPa 330 280
Fracture toughness--------Mpa*m1/2 3.8 3.5
Flexural Strength (MOR)---MPa 330 320
Compressive Srrength------MPa 2600 2300
Thermal Expansion (CTE)---10-6/K 8.2 8.0
Thermal conductivity------W/(m.K) 30.0 26.0 |
|
Chesterton’s 1210 Ceramic Stationary Seal Face may be used with 891 and 440 rotary seals to form a dual mechanical seal. The 891 is the inboard seal exposed to the process fluid. The 440 is the secondary (outboard) seal that seals barrier fluid to the atmosphere.
Can supply variable barrier pressure through the unit.
Shields the environment from the pumped fluid.
Provides a clean fluid to the inboard seal faces.
Can operate as a pre-installed "stand-by" seal in the event of primary seal maintenance. |
|
|
|
see the results for the following category
