|
|
|
Gericke offers a comprehensive range of different diverter valves for pneumatic conveying systems. Starting with simple flat diverter valves, Gericke offers for dense phase conveying systems plug diverter valves and for hygienic applications pipe selector diverter valves type PS. The PS valve is suitable for a wide range of materials and all types of pneumatic conveying systems up to 4 barg. FDA approved materials to meet stringent hygiene requirements. Fast clean version to allow frequent and safe disassembly, gas tight seal which remain inflated even during change along. This valve is suitable for both diverting and converting modes.
|
|
90° Diverter
Series 229 & 237
Compact, Abrasion Resistant
The Dynamic Air 90° Diverter is a reliable, low cost, compact and simple design of heavy duty construction. A positive rubber-to-rubber seal is created by the internal flapper which presses against the unused port. The seal improves as the conveying pressure increases, ensuring better performance against leakage in even the most severe dry bulk solids applications.
Features
Abrasion resistant
Positive sealing to 100 PSIG
Full port design
Economical
Compact, low profile
Low maintenance
Position sensors standard
|
|
Fills hoppers via cyclonic separation in the inlet load tube and
exhausting air in the outlet tube.
Valves can be stacked on top of each other allowing multiple sources to multiple hoppers.
Standard Features
- Stainless steel material contact points.
- Lightweight aluminum frame, corrosion resistant.
- Positive blade lock (PBL) between blade and cylinder rod.
- Active compression seals (ACS).
- Internal magnetic piston cushioned air cylinder.
- Stacking design for multiple conveying lines.
- Rated for 82oC (180oF).
|
|
Features:
- Seal rings at each port
- Full round port pass way design
- Heavy duty body design for pressure surges up to 90psi (6.0bar)
- Manual or pneumatic operated
- Heavy duty pneumatic actuator with integrated mechanical stops
Application:
- Suitable for granular and pellets
- For distributing or merging of product flow
- For differential pressure up to 60psi ( 4.0 bar)
|
|
|
|
|
|
The V-Diverter valve is used especially for diverting the bulk material flow in pneumatic dense- and dilutephase conveying systems.
The patented design of the plug enables application in any conveying direction.
Design characteristics
- suitable for pneumatic dense- and dilute-phase conveying systems
- smooth and gap-free transition due to patented design of inlet and outlet
- single channel design avoids plugging
- high dust and pressure tightness due to sealing pressing against the housing
- pressure tight from -1.0 to +6.0 bar (g) gauge to the outside and the non activated leg
- high reliability based on maintenance-free actuator
- solid temperature range from -20 to +120°C and ambient temperature range -20 to +40°C for standard design
- no additional safety device necessary as there are no moving parts outside the valve
- easy installation in all orientations because of integrated cast flanges and supports
- easy subsequent change of complete drive from left to right side of diverter valve
- easily visible direction indicator of plug orientation
- direct control of plug orientation by proximity switches
- all bolts in stainless steel
- low total weight
- defection angle 45°
|
|
Bulk flow has to be distributed an collected. For that diverter valves with the highest demand on functionality and operational safety are used. For product pureness deposit-free and CIP capable diverter valves are indispensable.
Their maintenance-free operation is a deciding factor for the profitability of the plant. Diverter valves from Coperion Waeschle fulfil these numerous requirements even at high pressure and temperature ranges.
|
|
|
Twin-Outlet Diverting Rotary Valve combines the function of a rotary feeder/airlock and diverter valve in one simple mechanism. Select left or right discharge by changing rotor direction via motor and reversing switch. Only one moving part. Very compact. Exclusive tapered rotor allows rotor gap to be easily adjusted. Heavy cast aluminum, iron or stainless steel valve body. Adjustable packing gland shaft seals -- purge available. Heavy duty permanently sealed outboard roller bearings. Ideal for vacuum or pressure conveying systems. Available in five sizes with capacities up to 2,500 cubic feet per hour.
|
|
|
|
|
|
The M-Diverter valve is used especially as a distributor of bulk materials.
The geometric design of the plug enables application in any conveying direction diverting or merging of the material flow from four lines to one or reversible.
Design characteristics
- suitable for pneumatic dense- and dilute-phase conveying systems
- smooth and gap-free transition due to patented design of inlet and outlet
- single channel design avoids plugging
- high dust and pressure tightness due to sealing pressing against the housing
- pressure tight from -1.0 to +6.0 bar (g) gauge to the outside and the non activated leg
- high reliability based on maintenance-free actuator solid temperature range from -20 to +120°C and ambient temperature range -20 to +40°C for standard design
- no additional safety device necessary as there are no moving parts outside the valve
- easy installation in all orientations because of integrated cast flanges and supports
- flanges easy accessible; no special connections required
- easily visible direction indicator of plug orientation
- direct control of plug orientation by proximity switches
- all bolts in stainless steel
- low total weight
- standard design with electrical connections in IP 65
- defection angle 4 x 45°
|
|
Quik-Vent™
Vacuum/Pressure Relief Valve
Series 684
Controls unsafe pressure conditions
The Quik-Vent vacuum / pressure relief valve is an excellent safety device for mounting on storage silos, bins or any other container to relieve excessive or unwanted air pressure that might be generated by a pneumatic conveying system or other process equipment.
Unsafe conditions are easily controlled by the Quik-Vent vacuum/pressure relief valve. Generous ports quickly exhaust air or gases to protect against sudden positive or negative pressure conditions.
Optional sensors are also available to provide an electrical signal to indicate when over or under pressure conditions are present.
|
|
The product range of Gericke rotary valves includes high quality valves including fall through valves, blow through valves for pneumatic conveying, fast cleanign valves with retractable endplate and rotor, autoguided by rails. Small leackage and full certification as flame containment equipment and pressure reistant units, the valves can be used in hazardous areas for explosion prevention and containment.
Hypergienic valves for isolator or glove box applications are developped for Pharma processes.
|
|
|
Integrate a Donaldson Torit Rotary Valve into your collector to create a complete system that automatically and continuously transfers dust from the hopper to the conveying system or collection container. Rotary valves are designed with a precision seal that keeps air out of the hopper and safeguards the performance of the collector. Donaldson Torit Rotary Valves are available in either AN, CI or F-Series
|
|
* Heavy duty construction
*Large inlet and outlet in relation to the rotor volume
* Outboard bearings
* Packing gland type seals
* Versions in accordance with ATEX 94/9/EC
Application: Discharge airlock valves for dust collector filters and cyclones.
Designed for a wide range of products, systems and operating conditions, they are also used as discharger and metering valves below silos and hoppers.
|
|
Airlock
- High filling efficiency
- Sheared angle inlet
- Minimum air leakage
- Explosion proof models available up to 10 bar g
- Customised solutions
- Bored flanges in accordance with PN 10, ANSI 150 lbs and JIS
|
|
Description:
The CO.RA. SANITARY ROTARY VALVE is characterized by a double rotor. The big rotor is used to transfer large quantities of product while the smaller rotor is used to obtain the pre-regulated quantity of product required. The SANITARY ROTARY VALVE is easy to disassemble and clean.
|
|
Hygienic Dairy rotary valve / USDA approved
- USDA approved
- Easy removal of rotor for fast and efficient cleaning
- Smooth product contact surfaces in food grade material
- Rotor pockets radiused and polished to Ra = 0.8 µm (150 grit)
- Rotor vanes chamfered on ail edges
- Flame proof and explosion shock resistant versions available
|
|
If controlled feeding from or into silos and hoppers in a very confined space is required Rotary Valves are the ideal solution.
The sealing of negative pressure cyclone and dust filter outlets is the other classic application.
RVS-type Blow-Through Rotary Valves have been developed in accordance with the criterion of maximum scope in application.
They have been designed for the controlled discharging of powders or granular materials from silos, bins, hoppers, cyclones or dust collectors into low- and medium-pressure pneumatic conveying lines.
|
|
Rotary Airlocks - Standard Rotary Valves
The prime function of a rotary valve is to regulate the flow from one chamber to another while maintaining a good airlock condition. The product is mainly in dry powder or granular form.
In the dust filtration field good airlocks are essential on cyclone and bag filter application in order that the manufactures quoted high dust collection efficiencies can be maintained. Airlocks are also important in the pneumatic conveying industry, where product is regulated into a high pressure conveying line while minimising air leakage.
With Rotolok there are no double standards, all our standard valves are precision machined for close tolerances and minimal eccentricities Pressure differentials to 20psi and temperatures to 400°C.
Extreme Pressures and Temperatures can be accommodated with special designs, if your application requires such considerations contact Rotolok Engineering team.
|
|
High pressure rotary feeders are mainly used for the discharge (dosing) of pellets and powders from silos. Furthermore they are used as a feeding device in pneumatic dense phase and dilute phase conveying systems with a differential pressure up to 4 bar (g).
High Pressure Rotary Feeder Type HDS
The HDS rotary feeders are mainly used for the discharge (dosing) of pellets and powders from silos. Furthermore they are used as a feeding device in pneumatic dense phase and dilute phase conveying systems with a differential pressure up to 3.5 bar (g).
|
|
|
The medium pressure rotary feeders are mainly used for the discharge (dosing) of pellets and powders from silos and hoppers. Furthermore, they serve as feeding devices in pneumatic dilute phase conveying systems with a differential pressure up to 2.0 bar (g).
|
|
Lugged Type
API 609 T2
DIN EN 558-16
* Compact design
* DN50 - 1000
* PN10 - 100
* 2" - 40"
* ANSI 150 - 900
* Data sheet (PDF)
|
|
Double Flange
ANSI B16.10
* Gate valve replacement
* 3" - 30"
* ANSI 150 - 600
* Data sheet (PDF)
|
|
Double Flange
DIN EN 558/F4
* Simple mounting
for large Diameter
* DN80 - 1600
* PN10 - 100
* 3" - 64"
|
|
Double Flange
ISO 5752/F16
* World-Wide standard
* DN50 - 1800
* PN10 - 100
* 2" - 72"
* ANSI 150 - 900
|
|
Buttweld S1
* No flange tightness problems
* DN80 - 1500
* PN10 - 100
* 3" - 60"
* ANSI 150 - 600
|
|
For feeding bulk materials into pneumatic conveying systems and discharging out of hoppers and silos.
Coperion Waeschle has worldwide the largest product range. We are able to fulfil all requirements of a modern bulk handling plant in all sizes and pressure ranges.
|
|
Bush & Wilton's IF "U" Rotary Airlocks are very cost-effective valves designed for use under gravity, pressure and vacuum conditions.They are suitable for metering a wide range of dry solids, granular, pelleted and powdered type materials from the outlets of silos, hoppers, cyclones, mixers, weighers, etc.
- HEAVY DUTY BODY
- END COVERS WITH SEALED FOR LIFE BEARINGS MOUNTED OUTBOARD
- GLANDS STUFFING BOX TYPE WITH PURGE FACILITY OPTIONS
- ROTORS ADJUSTABLE BLADED OPEN TYPE FABRICATED (CLOSED TIP OPTIONS)
- VARIED OPTIONS OF TIPS TO SUIT PRODUCT NEEDS
- BODY VENTS
- ABRASIVE DUTY TYPES (TUNGSTEN CARBIDE TYPE WITH ABRASIVE RESISTANT ADJUSTABLE TIPS)
- COMPLETE DRIVE OPTIONS
|
|
Features:
- Anti shearing device (patented) for gentle product handling
- Integrated leakage air vent for improved filling efficiency
- Heavy duty housing and bearing support for minimized rotor tolerance
- Closed end rotor
Applications
- For use with granular products and pellets
- For gravity discharge and metering
- For feeding pneumatic conveying systems
- Suitable for differential pressure up to 15 psi (1bar)
|
|
Drop-thru DIN PN10 - 1bar
* Minimum gas leakage
* Heavy duty construction
* Sheared angle inlet
* Large inlet and outlet without hindrance
* Flanges in accordance with
DIN PN10 or ANSI 150
* Versions in accordance with ATEX 94/9/EC
Application: Volumetric feeders for powders in pneumatic conveying systems or discharger and metering valves below silos and hoppers.
|
|
|
MSRT (tapered bore rotary valves) are designed for use under gravity, pressure and vacuum conditions. They are suitable for metering a wide range of dry solids, granular, pelleted and powdered type materials from the outlets of silos, hopper, cyclones, mixers, weighers etc.
|
|
|
|
