|
|
|
|
|
|
Flat-II
Flat-II nonrotating, double-acting cylinder provides the answer to applications where rotation cannot be tolerated and space is at a minimum.
Nonrotation is achieved with dual piston rods and a rod end block that insures the rods work in tandem. Eliminates the need for external alignment devices, such as guides, rods and alignment posts or pins.
Body - 304 Stainless Steel
Heads - Anodized Aluminum Alloy
Piston Rod - Ground and Polished 303 Stainless Steel
Piston Seals - Buna N (High Temperature Seals Optional)
Rod Bushing - Oil Impregnated Bronze
Rod Seals - Buna N O-ring (High temperature seals optional)
Rod End Block - Anodized Aluminum Alloy
Pressure Rating - 200 PSI Maximum (Air only)
Temperature Rating - From -20°F to +150°F (-25°C to +65°C) Buna N seals with a temperature range of -20°F to +150°F (-25°C to +65°C) are standard in all Bimba air cylinders. Fluoroelastomer seals rated for higher temperature applications are available. If cylinders are operated below -0°F (18°C) for extended time periods, special modifications may be required.
Special seal materials are available upon request!
|
|
Non-Rotating Air Cylinders
* Bimba’s new Non-Rotating Original Line stainless steel body air cylinder design consists of a unique square piston rod with rounded corners. The square rod prevents rotation better than other rod configurations, and the rounded corners provide longer seal life than conventional hexagon rods. The unusual geometry of the square rod also provides superior rotation control.
* All bore sizes have a rotational control of less than or equal to ±3 degrees. Bore sizes for the non-rotating cylinders are 9/16", 3/4", 1-1/16", 1-1/2", 2", and 2-1/2".
* The special high strength aluminum alloy rod guide provides high load carrying capability and abrasion resistance. The urethane-based rod seal provides excellent seal life and leak-free service.
* The Non-Rotating Original Line cylinder is dimensionally interchangeable with the standard Original Line stainless steel cylinder.
* Available in Double Acting and Reverse Acting models.
|
|
|
|
|
|
These products offers a wide range of traditional cylinders and innovative ones as well:
Cartridge Cylinders : Threaded piston rod, No-threaded piston rod. Bore size: 6 - 10 - 16.
Mini Cylinders Iso 6432: Single and Double-acting cushioned, Single or through piston rod. Bores: 8, 10, 12, 16, 20 and 25.
Mini Cylinders Inox ISO 6432: Double-acting magnetic; Double-acting without magnet. Bores: 16, 20 and 25.
Cylinders A95: Single and Double-acting cushioned; Single or through piston rod. Bore size: 32, 40, 50 and 63.
Compact Cylinders: Single and Double-acting magnetic; Single or through piston rod magnetic; Antirotation magnetic. Bore size from 12 to 100 mm.
Short Stroke Cylinders: Single and Double-acting magnetic; Single or through piston rod magnetic; Antirotation magnetic. Bore size from 12 to 100 mm.
Cylinder VDMA ISO 6431: Double-acting cushioned magnetic; Single-acting magnetic; Single or through piston rod magnetic; Tandem. Bores from 32 to 125 mm.
Rotary Cylinders : Double-acting cushioned and magnetic with male pinion; Double-acting cushioned and magnetic with female connection. Bores from 32 to 100 mm.
Magnetic Switches, Guide Units, Piston Rod Lock, Mounting Accessories.
|
|
Our Bansbach Feinmechanik AG Swiss facility manufactures special pneumatic cylinders and pneumatic accessories. Our Quality, Reliability and Durability is second to none!
Our contract manufacture business is the third main pillar of our company. Our customer's satisfaction is the Center point of this business. All products are customer specific and correspond exactly to the requirements of the application; even for very low quantities we maintain the highest quality cylinders.
Special pneumatic cylinders:
Custom products are designed, developed and manufactured according to the customer's request. That means we can help you with any application. Any project, Any time!
|
|
ISO Cylinders
Conforming to ISO 6431/6432 Standard Specifications, Bimba's ISO cylinders are designed to be easily interchangeable throughout the world. Bimba meets your needs.
Reliable service from a world-wide leader producing millions of actuators each year
Pre-lubricated for longer, maintenance free operation
Shock absorbing bumpers
Roll formed threads
High strength pistons permanently rivetted and sealed
Roller burnished stainless steel rods
Advanced bearing and seal materials for higher speed applications
Double rolled construction
Permanent mechanical retention; needles cannot blow out under pressure
Space savings available resulting from smaller external dimensions
Heads available i n Aluminium, Stainless Steel and Delrin®
Rapid design and delivery time for custom modifications
|
|
Standard Air Cylinders
* The "Original", with a "mirror finish" 304 stainless steel body, double-rolled end caps, sintered bronze rod bushing, Buna N "U" cup seals and our specially formulated HT-99 lubricant.
* Bore sizes: 5/16", 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", 1-3/4", 2", 2-1/2", 3". Wide variety of mounting styles. Many standard catalog options: bumpers, extra rod extension, Magnalube® G lubrication, heavy spring, rotated ports, low and high temperature options, magnetic piston, rod wipers, no-thread rod and more!
* Quick delivery of catalog models -- we stock more than 150,000 and can make any catalog model in 5 days or less.
* If you need something a bit different than what's in the catalog, call us! More than half of our business is "special" cylinders that we designed for specific applications.
|
|
Original Pancake® Cylinder available in 8 bore sizes Multi-Position Series PD3
Square 1® Series Cylinder offers space saving design "F" Series Stainless Steel Body Cylinders
Global SeriesTM Cylinder is a true metric interchange Hi-PowerTM Cylinder offer strokes to 42"
"GT" Series Guided Toolplate Cylinder is based on the Global SeriesTM Cylinder LongstrokeTM Cylinder offer strokes to 42"
Pancake® II Standard Series PSD, PSR, PSX, PWD & PTD
NFPA Air Cylinders
Pancake® II Nonrotating, Twin Rod Series PND
Swing Clamp Cylinders
Stopper Cylinders
|
|
High performance, long life, low maintenance: the top quality of Parker-Origa`s rod type cylinders is a result of decades of experience. Special customer specific solutions are part of our daily business.
Innovative cylinder concepts with excellent characteristics are the basis of the Parker-Origa cylinder programme. The inherent advantages are important factors for operation in system solutions. Modern automation with high efficiency is no longer a dream. Special solutions, which are developed for individual projects, guarantee optimal efficiency.
|
|
Air Cylinders with Adjustable Cushions
The Bimba Air Cylinders with adjustable cushions have a readily accessible cushion needle for easy adjustment, double acting models, and a 304 stainless steel body with mirror finish I.D.
High strength aluminum alloy porting ends and ground and roller burnished 303 stainless steel piston rods come standard. Also, the air cylinders have Buna N "U" Cup Seals, low breakaway friction - less than 5 PSI - and special stroke lengths available on request.
Air cylinders come in 3/4", 1-1/16", 1-1/2", 2", 2-1/2", and 3" bore sizes.
Bimba's cylinders with air cushions provide a possible solution to destructive energies. The air cushion traps a small amount of exhaust air at the end of stroke, providing an air pocket that decelerates the load. This reduces the potentially destructive energy being transmitted to the cylinder and other components.
|
|
|
Agroalimentary jack ICL Specific ISO 6431 Diameters: 32, 40, 50, 63, 80, 100 and 125 mm Races: 25, 50, 80, 100, 125, 160, 200, 250, 320, 400, 500 (longer races on request) Corrosion resistant, including fixings Measurements according to the standards ISO Sensor easy to install and adjust
|
|
Extruded Flat Lift Table
EF1-based, guided cylinder with four shafts for maximum rigidity. It is designed for lifting applications where other non-rotating cylinders cannot handle an overhung load and space is at a premium.
Four-shaft support withstands offset loads and moments.
Simple, efficient design provides economical alternative to other costly guided actuators.
Joins the EF family of products, so shares all the same benefits--long service life, low friction operation, fast delivery.
Convenient wide tooling mounting surface.
Intended for vertical lifting applications (should not be mounted horizontally or with tooling plates facing down).
|
|
Z Line Air Cylinders
The Bimba Z Line Air Cylinders are for extremely tough applications.
The Z-Line air cylinder has the rolled-in construction of the Original Line but features the following: Larger diameter, two-piece 303 stainless steel piston rod HEX-STUD rod end thread of heat treated alloy steel - easily removed in case of failure due to overload, and cushion quiet elastomer bumpers.
No charge options include the Magnalube G, Molycoated body, and magnet.
Bore sizes for the Z Line cylinders are 3/4", 1-1/16", 1-1/2", and 2".
|
|
|
Stroke is contained within the cylinder itself for space saving advantage. Allows force to be applied in both directions. Single acting, double acting, double purchase and track models available. Wide range for bore sizes and options
|
|
Ultran Rodless Cylinders
The Bimba Ultran rodless cylinder provides one of the highest coupling strengths available. This means it can carry higher loads without causing the piston to uncouple from the carriage.
Bimba also offers two magnetic coupling strength options (Gold and Silver) to suit a wide variety of applications. The Silver option uses two sets of magnets instead of three.
Bore sizes are 5/16", 7/16", 9/16", 3/4", 7/8", 1-1/16", 1-1/4", 1-1/2", and 2".
Bimba offers a model with built-in guides (Ultran Slide) and an unguided unit (Ultran).
Save space and streamline your design with the Bimba Ultran rodless cylinder! Application possibilities include transferring, feeding, door opening, cutting, silk screening and overall length savings.
|
|
Guiding cylinder
with two slide guides
with short slide guide
with safety unit
with slide guide underneath
Technical Information
· ZSS and ZKS have been designed for higher loads.
· By mounting a linear guide way on the bottom side of the cylinder, very high loads and moments can be carried forward
· Maximum stroke 3000 mm, longer on
· ZSS with two guiding carriages and a fitting length just like the ZS standard cylinder
· ZKS with a guiding carriage
|
|
All Stainless Steel Non-Repariable Cylinder
Corrosion resistant 303 Stainless Steel end caps.
304 SS body with mirror finish ID for long, reliable seal life.
Urethane rod wiper designed to withstand exposure to harsh chemical solutions while limiting ingress of the solutions and application matter into the cylinder.
PTFE-based rod and pivot bushings selected for their resistance to many commonly used cleaning solutions.
Nitrile seals are standard with optional high temperature or other materials available.
|
|
All Stainless Steel Repairable (Bell Ring Style)
* The new all stainless repairable Original Line cylinders are ideal for food processing, chemical, medical, pharmaceutical, offshore or marine equipment, and energy production or waste management applications. The bell ring design also offers the added benefit of full repairability without the need for hand tools by securing the body to the rod guide with a knurled, threaded nut.
* Bore sizes for the all-stainless steel repairable cylinders are 3/4" and 1-1/16".
* Engineering specifications include 304 Stainless steel body, low friction Buna N "U" Cup seals and rod wiper, 303 Stainless steel endcaps, piston rod, and bell ring nut, and Composite FDA approved rod bearing and FDA approved lubricant.
|
|
Styles:
- Tie Rod "Clean" Round Body
- Clean Round Body
Ports:
- BSP and NPT
Materials:
-316 Stainless Steel
Action:
- Single acting/ spring return and double acting
Rod Styles:
- Single and double rod ends
Mounting Styles:
- All popular styles
Bore Sizes:
- Tie Rod:
- Metric: 25mm to 102mm
- Imperial: 11/2" to 4"
- Clean Round:
- Metric: 25mm to 76mm
- Imperial: 1" to 3"
Pressure Ratings:
- 10 Bar Pneumatic
|
|
Three-Position Cylinders
Bimba's Three-Position Original Line stainless steel body cylinder provides three positions with a single cylinder.
Bimba offers the performance and quality of the unitized Original Line cylinder design along with three positive stroke positions.
|
|
TRD Manufacturing
TRD Manufacturing Cylinders are recognized for their durability, high quality construction and long-lasting performance. Manufactured in several different types including, NFPA-interchangeable cylinders, specialized cylinders and accessories, TRD Cylinders represent a significant step towards Bimba's strategy to expand their industry-leading line of actuators.
Advantages of TRD Cylinders Include:
* Space saving design
* Many cylinder options to choose from
* Precision designed to provide accurate linear movement and positioning
* Other models include all stainless steel (SS) and electroless nickelplated (EN), and low friction for smooth operation (LF)
|
|
Series of round jacks:
MECSTREME Æ25 with 125mm resists corrosion
(stainless 304)
and REXTREME Æ32 with 80mm resists the acids
(stainless 316)
Conform to the standard ISO 15552.
|
|
Morin Series S Pneumatic Actuator
Stainless Steel Quarter-turn
Spring Return and Double Acting Actuators
Output Torques to 238,000 lb. in. (26,894 Nm)
General Application
Designed for 'on-off' or modulating control of any quarter-turn ball, butterfly, rotary plug or damper style valve applications. To be used in chemical process, food & beverage, iron & steel, off-shore marine, pharmaceutical, power, oil & gas, pulp & paper, and textile industries.
|
|
ISO 6431/ 15552 - VDMA 24562 - NF E 49-003 compatible cylinder - PEC type
Available functions :
* single acting
* double acting
* double acting, through rod
* ollow through rod
* supply on the same extremity
* rotation-proof device
65% volume saved compared to an ISO 6431 cylinder
|
|
Series KPZ Dia. 16 with 100mm, race 5 with 100mm.
Double jack and simple effect, tandem and multiposition, possible antirotation.
Crossing, hollow or hexagonal stem. Food by the back. Small overall dimensions.
|
|
|
|
|
|
PS Series Linear Slide
The PS series is a compact lightweight unit with a replaceable air cylinder. Floating piston rod coupling eliminates cylinder binding. Units are permanently lubricated for non-lube air operation, allowing for OSHA compliance. Aluminum body and end blocks contain tapped holes and dowel pin holes for precision mounting or fixturing. Standard end plate to stop shaft vibrations.
Features:
Body: Anodized aluminum for reduced weight with multiple mounting surfaces with dowel location holes. Compact size for added space savings
Air Cylinder: Standard stainless steel body and rod for corrosion resistance and permanently lubricated for non-lube service.
Alignment Coupler: Isolates piston rod from side loading, increasing service life.
Optional Shock Absorbers: Recommended for high cycle applications to absorb shock loading, and provides end of stroke adjustment.
Optional Proximity Switch Sensing: For applications requiring end of stroke verification, available for extend and retract positions.
Rear Tooling Plate: Dampens guide rod vibration for smooth operation, and houses shock absorber for extend position.
Bearings: Four recirculating linear ball bearing for maximum load capacity that are sealed from contamination. Self-aligning for maximum guide rod support.
Guide Rods: Hardened steel to Rc60-65, precision ground and polished.
|
|
|
For over 25 years, Compact®Automation has been developing custom solutions to meet the unique requirements ofour customers. From repositioning part locations to 100% custom products, Compact®has engineered over 22,000custom designs and can offer our customers effective and efficient solutions regardless of the complexity. Our designexpertise, coupled with the highest quality standards, enables us to provide you with superior automation products.
|
|
Pneumatic cylinders M (Metallurgy)
Double acting pneumatic cylinders - single rod Series C: with pneumatic damper at the end position on the both ends cylinder
Series A: without stop end stroke damper
|
|
HJDAL
Double Acting. The square rod style accomplishes the non-rotating function in an extremely simplified design. The square rod eliminates the need for rod end quide blocks or internal guide pins common to double acting, non-rotating cylinders. Wide range of bore sizes 3/4" to 2 1/2". Unique body allows sensor switches to be mouted on 3 different sides when magnet type is required. Four different sensor switches available including hall effect or reed types, and indicator light (LED). Other options include bumpers, male rod thread or no rod thread, foot mount, and flange mount.
|
|
Double acting, Single End Rod; Compact; with Magnetic Scan; with Female Thread
Other stroke lenghts and piston-Ø to 100 mm upon request.
Ø 12 - 25: max. 200 mm stroke length
Ø 32 - 40: max. 300 mm stroke length
Ø 50 - 100: max. 400 mm stroke length
|
|
Morin Series B Pneumatic Actuator
Ductile Iron/Stainless Steel Quarter-turn
Double Acting and Spring Return Actuators
Output Torques to 238,000 lb.in. (26,984 Nm)
General Application
Designed for 'on-off' or modulating control of any quarter-turn ball, butterfly, rotary plug or damper style valve applications. To be used in chemical process, food & beverage, iron & steel, off-shore marine, pharmaceutical, power, oil & gas, pulp & paper, and textile industries.
|
|
|
|
