|
|
The Diaphragm Amplifiers are miniature interface devices which perform the same function as a piloted three-way valve, but at low outlet flow rates. Pneumatic signals of several inches water gauge applied to the input will control the output pressure up to 35 PSI in both digital and analog systems.
Diaphragm Amplifiers are very suitable for providing pneumatic signals to air-piloted valves for powering small cylinders. They are also used at fluidic signal levels for providing isolation and in timing circuits.
|
|
The TESCOM VT 3-way air operated valve provides high cycle life in a compact design in stainless steel or brass body construction with pressure ratings of 10,000 psi and 6,000 psi respectively. With its balanced poppet valve design, the VT minimizes seat wear in high cycle applications and can be actuated with a minimum/maximum range of 80 - 110 psi. The bi-directional balanced valve allows for versatility with flow direction and functions as normally closed, normally open and as a two source selector valve.
Advanced Features:
• 1/4" & 3/8" ports
• Cv = .75
• Balanced main valve
• Optional solenoid valve
• 3 way, 2 position
• Universal operation
• Leak tight integrity - Class VI shut-off (bubble-tight)
• Pneumatic & hydraulic applications
Typical Applications:
• Component pressure cycle testing
• Two source selector valve
• Fill and dump applications (e.g. airbag canister filling, gas spring filling)
• Emergency shut-off
|
|
2, 3 port valve
4S1 series
4.5
M(D)3SA1
46
(small pneumatic valve)
M3GA
156
4G series
4.0 to 16
MN3GA
248
Pilot operated
soft spool valve
MN3S0
4.0
MN4S0 series
368
One side solenoid type
MT3S0
3.0
4K series
M3KA
516
M3MA0
3M series
0.1 to 0.5
686
(small pneumatic valve)
M3MB0
Direct acting
poppet valve
M3PA
1.9 to 5.4
3P series
710
M3PB
B * P51
742
Pilot operated
P/M/B series
0.45 to 0.84
poppet valve
(miniature pneumatic valve)
N * P512/3/4
746
|
|
|
These 3/2-way normally closed valves in base-mounting design are available as a complete Series in Sizes 4, 8, 12 and 30 (outlet ports G 1/2 to G 2, on both sides for more piping flexibility). valves offer the design features of the well-proven ROSS poppet valve technology and fully comply with the relevant criteria of DIN EN 692 as well as DIN EN 954 (Cat. 3 and 4). The valves provide dynamic, cyclic and internal monitoring during each actuating and de-actuating movement. DM2™ valves have been approved by Deutsche Berufsgenossenschaft (BG-PRÜFZERT, MHHW, Cert.-No.s 06 008 / 06 021).
|
|
|
Directional control and failsafe function in valve actuator circuits in corrosive and hazardous environment. 3/2 direct operated solenoid valves available in two versions: A/ Normally closed (U131 types) - NAMUR interface for direct adaptation to the actuator including integrated flow regulators. B/ Universal (U133 types) with NPT 1/4 pipe connection and also with Manual Reset function (U033X types).
|
|
|
|
|
|
The Pneumatic Solenoid Valves 720 Series are available in both NC and NO version. They include all innovations, which are present in Matrix solenoid valves, both in materials and operating principles.
They couple simplicity and reliability with high dynamic performance. Response times are of milliseconds range, while their operating life is over 500 million cycles. The Series comprises Vacuum versions designed for uses with vacuum technique.
Due to the facility to be speed-up controlled,dynamic characteristics become even more improved: standard solenoid valves equipped with 24 VDC control present response times lower than 5 ms in opening and 2 ms in closing, with a maximum operation frequency 200 Hz. On the contrary, solenoid valves equipped with speed-up control present a response time both in opening and closing lower than 2 ms, with a maximum operation frequency 300 Hz.
Besides high-speed characteristics, solenoid valves 720 Series offer flow rate value to 100 l/minute (ANR), with supply pressure from 0 to 8 bar.
720 Series is available both in line assembly version and on sub-plate and is equipped with a range of accessories such as multi-position manifolds and speed-up driver boards.
|
|
|
|
|
|
750 Series 3/3 presents a small-sized single body with four utilities, assuming, according to the different models, the following configurations:
In the present model, all the innovations offered by Matrix technology, this combines special dynamic performance to the simplicity and reliability of manufacture, are present. Response times are of millisecond range, while operation life is over 500 million cycles.
With a speed-up kind control, dynamic characteristics are even more improved. Standard 24 VDC control solenoid valves have a response time lower than 5 ms in opening and than 2 ms in closing, with a maximum operation frequency 200 Hz. Speed-up control solenoid valves have a response time lower than 2 ms both in opening and in closing, with a maximum operation frequency of 300 Hz.
Besides high-speed characteristics, 750 Series solenoid valves offer flow rate values up to 100 l/minute (ANR) for every single outlet, with feeding pressure from 0 to 4 bar.
For 750 closed centres series, a lot of accessories is available, such as IP 52 or IP 65 connectors, manifolds with different positions and speed-up driver boards.
|
|
| ... products without technical information |
| |
3 WAY/4 WAY BALL VALVE
THREADED END OR FLANGED END
WITH OR WITHOUT (DIRECT) MOUNTING PAD ISO 5211
1000 WOG OR DIN PN16/40/ANSI 150L
STANDARD /FULL BORE
PORT TYPE: L/T/X
|
|
Series 100 - DN04 to DN50
Body, ball, stem : steel
Fields of application:
hydraulics, particularly in construction industry and agricultural machinery, mining industry, paint industry. (Seats and seals adapted to application)
|
|
TRIFLUX series is available both with L and T bore and allows to divert the flow in all directions including the inlet shut off, applicable to each of the three threaded ends. It is suggested for gas and water distribution, industrial and civil heating, water plants at medium pressure, hydraulics and pneumatic, non aggressive media and vacuum.
|
|
|
|
|
|
Flow Patterns:
Hayward Manual Three-Way Ball Valves come standard with a two port "TW" ball allowing for three flow configurations within 180 degrees of rotation. With the bottom port as the inlet, the flow can be directed out the left port, out the right port or shut off. Hayward Actuated Three-Way Ball Valves come standard with a three port "NT" ball allowing for two flow configurations within 90 degrees of rotation. With the bottom port as the inlet, the flow can be directed out the left port or out the right port, there is no shut off position. A "TW" ball, used with with the proper electric actuator, adds what is typically called a "center off position" to the "NT" flow pattern of actuated valves. An optional "TP" ball, used with either manual or actuated valves, allows flow through all ports at the same time or flow shutoff.
True Union Design:
This makes these valves very easy to maintain by allowing for easy removal from a piping system without breaking down the piping connections. Just unscrew the three assembly nuts and lift the valve body out of the line.
Easy to Actuate:
A manual valve can be easily automated. Just remove the handle and install the optional actuator mounting kit. The mounting saddle is integrally molded into the valve body. For rock-solid actuator mounting, the valve incorporates a unique design whereby the mounting bracket mounts directly to the valve body. This assures proper alignment of the actuator to the valve without creating any damaging side loads to cause premature stem seal failure.
No Metal, No Corrosion:
Hayward all plastic three-way valves contain no metal parts. The valves will never fail because of corrosion and they do not require painting or epoxy coating to stand up to aggressive environments.
|
|
GENERAL DESIGN
The floating ball is held between two pre-compressed
seals which ensure a tight, non-leak fit at both positive
and negative pressures. The ball’s rotational angle is
constrained by a stop pin and disc.
Cranked handles are incorporated to provide good
clearance for the operators hands.
Flat handles can be provided on request.
FEATURES Full bore valves provide an unrestricted flow path for
negligible pressure drop. Floating ball on pre-compressed seals minimises
wear and provides an excellent seal at positive and
negative pressures. High working pressures - see table on page 59. Operating temperatures from -20°C to +100°C.
1
4 Open to close in
/ turn (90°).
|
|
3-way Plug Valves
TUFLIN® 3-way Plug Valves for complex piping systems
The design and sealing principle of the TUFLIN® 3-way plug valve is based on the proven 2-way plug valve design. All configurations are suitable for more flexible and complex piping systems and applications.Typical applications of multiport plug valves:
* as changeover valves for pressure relief duties
* for by-pass or mixing operation purposes
* as switchover valves for filtration circuits
* in the pulp and paper industry
* in filtration or drying plants
|
|
| ... products without technical information |
| |
The Advantages at a Glance
Customer-specific design
Compact design and smaller envelope dimension is achievable with the Steripur Series actuators
Combination of many different nominal diameters
Optimized drainability
Minimized dead leg
Reduces surface contact, hold up volume and cross contamination of the product
Reduction of fittings, tubing and field welds in the system
Reduces qualification and validation documentation requirements
All end connections and materials are
|
|
The Solution For High Flow& High Pressure Requirements
- Flows up to 240 gpm
- 5000 psi (6000 psi intermittent)
- Pneumatic, hydraulic or solenoid operated
- Full Cartridge Style Valving
- Low Leakage
|
|
|
Multiport gauge valves facilitates different positioning of the pressure gauge or pressure switch without disturbing the main line. One 1/2" male or female inlet & three 1/2" NPTF outlets ports is the standard configuration of any multiport guage valve
|
|
Solenoid valve with BRASS and STAINLESS STEEL 316 body.
3 ways Normally closed and universal.
Seals: Buna (NBR), Viton (FKM), EPDM, Ruby.
Coils: Standard, Bistable, Explosion proof
Port size 1/8", 1/4" and socket.
Fluid temperature up to 180°C.
The 3 ways direct acting range is suitable for actuators control, and in application directly in contact with the process fluid (ais, gas compatible with valve materials, water, steam, liquids compatible with materials). THe class H coils permit to work up to 180°C and bistable coils allow low energy consumption for portable applications or where temperature increase must be avoid. The explosion proof coils works in potential explosive environments.
|
|
Technical data
Fluid: water, air, neutral fluids
Ambient temperature: -10 to +50 [°C]
Voltage: 230 [V], 50 [Hz]; 24 [V] DC
Coil power: 8,5 [VA]; 6 [W]
Protection enclosure: IP 65
Duty rating: always
Mounting position: optional
Materials
# seal - NBR
# body - brass
|
|
|
|
|
|
In an ever increasing typology of applications, is by now necessary avoid the oxidation involves any part of plant and instrumentation.
To meet this requirement, SIRAI® has designed a new solenoid valves series, characterized by the high quality of body material, made in PPS.
Besides solving definitely the problem of oxidation, these solutions allow to reduce the limescale.
The choice of an high quality polymer, particularly resistant to chemical and physical aggressions, allows to use these valves for a wide range of fluids, including low-pressure steam. PPS, furthermore, offers a good level of tolerance to ultraviolet rays and flames exposition.
These features, together with other peculiarities of the project, make these valves the best solution for several applications, especially in the field of small sterilizing autoclaves.
Solenoid valves are available in different versions: 2/2NC, 2/2NO, 3/2, 1/8” threaded or barbed ports. Also the electrical part draw up at the same level of high quality standards.
The compact coil, with a perfect balance between power absorption and magnetic performance, is available in “F” or “H” class, also homologated according to the main international standards.
|
|
|
Alcon 3-way General Purpose Solenoid Valves are ideal for mixing, diverting and venting applications. The U31, U32 and U33 Series feature a compact design available in a wide range or orifices. These valves are zero pressure rated and offer a choice of valve materials for its body and seals.
|
|
normally closed
TYPE: B919/920/921
TECHNICAL SPECIFICATIONS
Media: water, oil, air
÷ +130°C
Media temperature: -10°C
Ambient temperature: -10°C
÷ +50°C
Body material: brass (CW617N EN 12165)
Orifice material: stainless steel (AISI 303 EN 10088-3)
Operator material: stainless steel
Seal material: FKM
Coil power: AC 10VA (holding)
AC 16VA (inrush)
DC 7W
Protection class: IP 65 (with connector)
Standard manual override
|
|
|
The VV061 series is a direct operated 3-way solenoid valve designed for 4 and 8 station units with integrated compact manifold, valve, circuit board, base and fittings forming a single compact unit. VV061 series model has an optional power saving circuit that can be used for long-term continuous duty. This unit is available with one-touch or barb fitting and an optional connector cable with lengths of 300, 600, or 1000mm.
|
|
Media: air – water – gas – light oil - vacuum
Pressure range : 0 to 15 bar max
Media temperature : 100° C max
Ambient temperature : -10° to +50° C max
Media viscosity : 40 centistokes max
Mounting : any position
Weight (including coil) : 280 g
Opening or closing time : 20 milliseconds maximum
|
|
|
3/4" high capacity (DN22, kv=105 l/min) universal solenoid valve, operating pressure up to 2 bar in all directions (3/2 NC, 3/2 NO, collector, diverter).
|
|
3/2 way Solenoid Valve
direct acting solenoid valve DN3, fast acting, for neutral medium like air and water
port connections G1/4, body in brass, NBR seal,
circuit function: power free - outlet balanced, Pressure range 0 - 10.0 bar, Voltage tolerance ±10%,
Ambient temperature max +55°C / 131°F, with flat seal and fixing screw
Standard version
Protecting class IP65, with cable plug for cable-ø7 mm, Medium temperature: 0°C / 32°F up to +80°C / 176°F
|
|
Features :
‧ATEX Ex certified components approved for hazardous locations:
‧Corrosion resistant construction with standard manual override.
‧Direct mounting conforms to Namur VDI / VDE 3845 standard.
‧5/2 and 3/2 function selectable via 180° rotation of single adapter plate.
‧Exhaust feedback - provides spring chamber with instrument air preventing corrosion.
‧Wide operating temperature range -4°F to +122°F [-20°C to +50°C]. Optional Low Temp to -40°F [-40°C]
‧Also available: Intrinsically Safe and CSA/FM Explosion proof.
|
|
| ... products without technical information |
| |
|
|
