|
|
|
The fine threads of the needle valve permit excellent adjustment for precise control of flow. The flow is restricted in both directions and is adjustable from 0 to the equivalent flow of a 0.025" diameter orifice. The 7-turn adjustment needle valves are available in two models, the standard model and the fine adjustment model. The standard adjustment model has a pin angle of 6° with 10-64 threads; the fine adjustment model has a pin angle of 4° with 10-80 threads.
|
|
Connection guaranteed: a wide range of functions and variants - always harmonised to the respective requirements.
• Exhaust air/supply air flow control or without non-return function
• Flow rate 15 ... 4,300 l/min
• Threaded connectors M3 ... G3/4
• Push-in fittings QS3 ... QS 12 or PK-3 ... PK-6
• Variants with increased corrosion resistance
|
|
LS-V05C
Proportional Pneumatic Control Valve
The LS-V05C is an enhanced version of the LS System proportional, directional control pneumatic valve for high performance applications such as medical equipment, test & measurement systems, advanced automation and animatronics. The valve is designed to be paired with Enfield Technologies driver or controller/driver electronics such as the LS-C10, LS-C41, and C2s.
Features:
* Proportional
* High Speed and Flow
* Whisper Quiet
* Vacuum Capable
* High Linearity
|
|
General Description
Uni-directional
316 Stainless Steel or Brass in-line flow regulators for uni-directional operation (free flow return).
Bi-directional
316 Stainless Steel or Brass in-line flow regulators for bi-directional operation (separate flow control in each direction).
Operating Fluids
- Gases
Filtered lubricated or non-lubricated air, inert gas, sweet (natural) gases.
Sour gas option available
- Liquids
Low pressure hydraulic, mineral oil or water.
|
|
|
Angle Flow Control valves are designed to provide accurate flow control in a compact, labor saving package. Features like built in push-in fittings, pre-applied thread sealant, convenient swivel design and unique needle design all add up to a package that will save time, money and energy when accurate control is needed on pneumatic actuators.
|
|
The miniature Preset Flow Control is ideal for many applications involving pneumatic systems, including the control of cylinder speed.
The operation of the flow control is based on the movement of a small disc. The flat surface on one side of the orificed disc seals and permits flow through the orifice. The amount of flow permitted in the reverse direction is determined by the orifice size. In the forward direction full flow is permitted. The flow controls design allows a maximum supply pressure of 75 PSI with a minimum cracking pressure of less than 10” H2O. Orifice sizes are available from .004” to .040”.
|
|
|
EExPress™ is a new concept of 5/2 valve manifold to control pneumatic actuators in dangerous environments like chemical, petrochemical applications. The concept consists in an patented "integrated protection", a unique feature on the market today, which permits to install the manifold directly close to the actuators without being mounted in expensive explosion-proof pressurised cabinets.
|
|
|
Directional control and failsafe function in valve actuator circuits in corrosive and hazardous environment. 3/2 direct operated solenoid valves available in two versions: A/ Normally closed (U131 types) - NAMUR interface for direct adaptation to the actuator including integrated flow regulators. B/ Universal (U133 types) with NPT 1/4 pipe connection and also with Manual Reset function (U033X types).
|
|
NAMUR MOUNT 4 WAY PNEUMATIC VALVES (VAP)
PIPE MOUNT 4 WAY PNEUMATIC VALVES (VAP)
SUB BASE MOUNT
316L STAINLESS STEEL 4 WAY PNEUMATIC VALVES
|
|
2005 Series
Modular reality, plug together flexibility in design! 4-way solenoid air pilot actuated valves. Available in manifold & base mount. Supported electronic interface/bus protocols include DeviceNet, Allen-Bradley, Remote I/O and Profibus DP.
2012 Series
Modular reality, plug together flexibility in design! 4-way solenoid air pilot actuated valves. Available in manifold & base mount. Supported electronic interface/bus protocols include DeviceNet, Allen-Bradley, Remote I/O and Profibus DP.
2035 Series
Modular reality, plug together flexibility in design! 4-way solenoid air pilot actuated valves. Available in manifold mount. Supported electronic interface/bus protocols include DeviceNet, Allen-Bradley, Remote I/O, and Profibus.
|
|
|
|
|
|
2002 Series Valve
Modular reality, plug together flexibility in design! Sub-miniature 3-way and 4-way solenoid air pilot actuated valves. Available in manifold & base mount. Electronic interface options include DeviceNet, Profibus-DP, 1771 Remote I/O, and DeviceLogix.
Standard Specifications:
Cv: 0.20 to 0.25
Port Sizes: 1/8 NPTF, 4mm, 6mm
5 ported, 2 & 3 position, 4 way
Flow Capacity: 11.5 SCFM @ 80 PSIG / 246 NI/m @ 6 bar
Operating Pressure Range: 28" Hg. Vacuum to 150 PSIG / Vacuum to 10 bar
Pilot Pressure Range: 35 to 115 PSIG / 2.5 to 8 bar
Temperature Range (Ambient): -10°F to 115°F / -23°C to 46°C
2004 Series Valve
Modular reality, plug together flexibility in design! Miniature direct solenoid and solenoid air pilot actuated valves. Manifold mounting with DIN rail option. Electronic interface options include DeviceNet, Profibus-DP, 1771 Remote I/O, and DeviceLogix.
Standard Specifications:
Cv: 0.35 to 0.40
Port Sizes: 1/8 & 1/4 NPTF, 4mm
Flow Capacity: 16 to 18 SCFM @ 80 PSIG / 345 to 394 NI/m @ 6 bar
Operating Pressure Range: 28" Hg. Vacuum to 150 PSIG / Vacuum to 10 bar
Pilot Pressure Range: 20 to 115 PSIG / 1.5 to 8 bar
Temperature Range (Ambient): -10°F to +115°F / -23°C to +46°C
|
|
|
|
|
|
CL18 & CL26
Our CL18 & CL26 Series valves offer a low-cost alternative! 4-way solenoid air pilot actuated. Conform to ISO 15407-1. Simple wiring connectivity using 17mm DIN connectors. Available on bar stock manifolds, up to 12 stations.
ISO 5599/2 & 15407-2 Series Valve
Numatics ISO series valves are high speed, heavy duty valves, designed for general service on all types of automation. Valves comply with ISO standard 5599/2 for valve unit to base interchangeability. Direct solenoid and solenoid pilot actuated models available. They are true multi-purpose valves and employ the patented Numatics spool and sleeve assembly.
ISO 5599/1 Series Valve
Numatics ISO series valves are high speed, heavy duty valves, designed for general service on all types of automation. Valves comply with ISO standard 5599/1 for valve unit to base interchangeability. Direct solenoid, solenoid pilot and air pilot actuated models available. They are true multi-purpose valves and employ the patented Numatics spool and sleeve assembly.
|
|
| ... products without technical information |
| |
|
|
|
|
PS Series Linear Slide
The PS series is a compact lightweight unit with a replaceable air cylinder. Floating piston rod coupling eliminates cylinder binding. Units are permanently lubricated for non-lube air operation, allowing for OSHA compliance. Aluminum body and end blocks contain tapped holes and dowel pin holes for precision mounting or fixturing. Standard end plate to stop shaft vibrations.
Features:
Body: Anodized aluminum for reduced weight with multiple mounting surfaces with dowel location holes. Compact size for added space savings
Air Cylinder: Standard stainless steel body and rod for corrosion resistance and permanently lubricated for non-lube service.
Alignment Coupler: Isolates piston rod from side loading, increasing service life.
Optional Shock Absorbers: Recommended for high cycle applications to absorb shock loading, and provides end of stroke adjustment.
Optional Proximity Switch Sensing: For applications requiring end of stroke verification, available for extend and retract positions.
Rear Tooling Plate: Dampens guide rod vibration for smooth operation, and houses shock absorber for extend position.
Bearings: Four recirculating linear ball bearing for maximum load capacity that are sealed from contamination. Self-aligning for maximum guide rod support.
Guide Rods: Hardened steel to Rc60-65, precision ground and polished.
|
|
|
|
|
|
ISO/VDMA Series Metric Standard Interchangeable Cylinder
The ISO/VDMA Series is an aluminum body air cylinder line that is designed to meet all your international cylinder requirements. In fact, our ISO/VDMA Series cylinders are designed to meet the requirements of ISO 6431 (International) and VDMA 24562 (Germany). The combination of lightweight aluminum construction and proven reliability makes our ISO/VDMA Series the Superior Interchangeable metric, international standard air cylinder line.
GeoMetric® ISO/VDMA Cylinder
The GeoMetric® Series conforms to the following cylinder specifications: VDMA 24562, DIN/ISO 6431, and ISO/FDIS 15552. One of the most desirable features of the cylinder line is the dual switch/sensor groove design that is a standard offering on all GeoMetric®cylinders. The dual groove design offers great flexibility when mounting switches and sensors to the cylinders. One groove is a traditional round groove and the other is what we call the CombiGroove®. The CombiGroove® is a unique design that will accept round and angular switches/sensors.
|
|
GeoSlide Series Guide Unit
The GeoSlide guide units utilizes Numatics GeoMetric ISO 6431 VDMA cylinders. The FHG & FHK series offers high load carrying capabilities in a metric package.
Features:
Bore sizes range from 32mm to 100mm.
Strokes up to 500mm.
Linear ball or bronze bushings option.
Available in a "U" style body.
LCX Series Linear Slide
The LCX Series linear slide combines cost-effectiveness with proven dependability. An economical alternative with greater load carrying capabilities.
Features:
Low Cost
High Load Capability
Stainless Steel Shafts Available
Engineered Plastic Polymer Bearing
Available in 3 Bore Sizes
|
|
R Series Rack and Pinion Style Rotary Actuator
The R Series is a heavy-duty rack and pinion style rotary actuator that is designed to excel in the most rigid applications. The R Series includes a high torque-to-size ratio as well as accurate positioning.
RW Series Rotary Actuator
The RW Series Rotary Actuator design utilizes two independent piston cylinders, each piston has a crank arm attached to a crankshaft. As the piston strokes in its bore, the crankshaft rotates, pressurizing the opposite bore reverses rotation. This unique design has many features and benefits over conventional rotary actuators.
LR Series Low Profile Rotary Actuator
The LR Series rotary actuator is a low profile rack and pinion design. Two independent pistons drive their corresponding racks against the pinion thereby rotating the platform.
|
|
| ... products without technical information |
| |
Mistral
Wichita's Mistral pneumatic tension brake is attuned to the needs of the corrugating market for which it was originally designed. It is also a versatile product which is finding favor in additional tensioning applications. Wichita designers and engineers consulted extensively with mill roll stand manufactures and users to offer a tension brake ideally suited to needs of this particular market. The result is a compact, high performance, versatile brake capable of handling the tensioning needs of the latest machine designs, as well as existing equipment. The Mistral paves the way for increasing line speeds by 5.4 feet/sec. from 810 feet/min. (or slower) to 1,140 feet/min.
|
|
|
|
|
|
Get More for Less in E-Stop Braking — By Breaking from Convention
# 28 Torque Ranges
# Three Frame Sizes
# 6 Disc Configurations
High Torque, Low inertia Engineering
Innovators at low inertia brake engineering, Force Control Industries, Inc. reduces size and mass to deliver more of what you need from an E-Stop brake - fast acting response - while paring away what you don't want.
Compact, Action Packed Design
Highly compact, space efficient designs, Force Control Industries, Inc. E-Stop Brakes feature a small diameter, multi-stack brake stack. This minimizes cyclic inertia of the brake itself for faster stopping, while multiplying braking surfaces. The brake stacks are fitted with unique dry friction facing material rated for heavy duty performance. Exceptionally durable, the material provides a high-coefficient of friction for high stopping torque in a small package.
Purpose Built Design
Unlike general purpose brakes adapted for E-Stop applications, our purpose built design doesn't need to be large and heavy to dissipate high heat loads, because it isn't subjected to frequent braking cycles. You only need one stop per episode - but then with the fastest possible response time.
So, we designed our E-Stop Brake with small diameter, multiple discs for high braking torque with low inertia. It's the same formula we have applied for years in our high performance oil shear brakes.
Multiple springs provide fast response and balanced braking torque, plus enhanced safety factor in event of a broken spring.
|
|
Posistop® Oil Shear Brakes are designed to dissipate the heat buildup that destroy conventional braking devices. The Posistop® absorbs the energy generated by the braking action and controls the heat buildup - thus providing greater reliability and repeatability, as well as heat dissipation.
|
|
|
|
see the results for the following category : 
