|
|
|
Aquasorb A-30B/Bp is a sorption dehumidifier that condenses out the moisture. The chassis is made of stainless steel, which is especially important in condensing units. The rotor is, as always, washable, all energy is accumulated in the dry air. Aquasorb operates at dew-points below 0°C.
|
|
Clean and dry compressed air: it is vital to power up your busy production environment. Containing moisture, aerosols and dirt particles, untreated compressed air poses a substantial risk as it can damage your air system and end product.
Incorporating unique, patented technological innovations and extra energy-saving options, Atlas Copco's CD dryers provide you with the clean, dry air you are in need of to expand the life of your equipment and ensure the quality of your end product.
|
|
|
Eliminating dust, oil, moisture, carbon monoxide and any other harmful particle, the MED make respirable the most difficult environments. Certified THIS Medical, these treatment units of the compressed air are composed of a drier by adsorption, filters and catalysts. They fontionnent starting from any electrical motor compressor and can feed to 15 people in respirable air in conformity with standard NF INTO 12021.
|
|
Boreas Refrigeration Compressed Air Dryers with Variopulse
The proprietary design of Boreas heat exchangers incorporates large flow channels for low pressure drop, which translates into low operating costs. A built-in cyclone separator with our Ultramat zero-loss drain valve allows for the removal of condensed water without wasting any compressed air. The space-saving design brings cooling air in the front and out the top, allowing the unit to be placed next to a wall with other equipment on either side. All Boreas dryers utilise environmentally friendly R-134a refrigerant and are available in either air- cooled or water-cooled configurations. Volume flows of 1.800 to 28.500 m³/h are covered by the Boreas series.
|
|
The operation of compressed air systems with conventional adsorption dryers suffers from system-related pressure drop. This deficiency needs to be compensated via an increased compressor performance, this requiring a higher energy demand.
Cold-regenerated DRYPOINT® AC adsorption dryers offer a convincing solution to the problem:
BEKO has developed an adsorption dryer which limits the pressure drop to an average of only 0.25 bar, including the pre- and final filters.- Compared with conventional constructions, this represents an improvement of over 50%.
|
|
Compressed air always contains moisture, traces of compressor oil and dust particles.
These impurities can lead to serious problems. Corrosion pockets or deposits build up in air tools and equipment. This makes them operate less efficiently and reduces the quality of the products manufactured. Maintenance work becomes necessary and costly downtimes occur.
|
|
|
Dryers for compressed air with refrigerant circuit of the “LB - Little Bear”, “GB - Great Bear" and “Pole Star” series. There are 22 models whose capacity ranges from 36m3/h up to 10.800 mc/h. Either the R 134A or R 407C or R404a ozone-friendly refrigerant is normally used. The program is completed with Filters for compressed air "FH" series, , Manual, Electronic and Capacitive condensate drains.
|
|
The demand for 100% clean and dry air is becoming more and more essential because of both environmental demand and in order to prolong the lifetime of your equipment requiring compressed air.
To ensure both clean and dry compressed air, JUN-AIR offers three types of dryers: adsorption dryers, membrane dryers and CO2 dryers, which are - unlike many types of dryers in the market - designed for continuous operation.
|
|
DHA Series and CDA Series Heat-Les™ Dryers (60-1,600 scfm)
Critical applications and hostile environments challenge common industrial dryer designs. DHA Series (-40°F) and CDA Series (-100°F) dryers deliver unrivaled performance and reliability through standard and customized orientations. Pre-configured dryer packages range from a basic fixed-cycle unit to a high pressure, corrosion-resistant model. Every unit we build incorporates our AMLOC® energy management system to assure long component life cycles and maximum energy savings
|
|
ADR 100 ADR 140
Capacity (l/min.) 10.000 14.000
Electric tension (Volt/Hz/Ph) 400/50/3 400/50/3
Air connection ('') 2 2
Dimensions (l x w x h, cm) 86.5x101.7x110 86.5x107.7x110
Weight (kg) 260 293
Coolant R 134 a R134 a
Ordernr: Code
39629 ADR 100 B
39630 ADR 140 B
|
|
CNG Series
Single Tower Natural Gas Dryers
CNG Series adsorbers are single tower dryers designed to remove water vapor from Compressed Natural Gas in small to medium gas flow rates. Located at the inlet of the booster compressor, our unique binderless molecular sieve insures dry, pipeline quality gas (-80°F dew point or better) with minimal odorant fading.
Mobile, stationary and contracted regeneration packages available.
Single tower adsorption towers are an economical alternative to twin tower drying systems in CNG vehicular fueling stations which see intermittent or small gas flow rates (up to 300 scfm).
Down-flow design minimizes fluidization of the adsorbent insuring maximum life.
Optional Moisture Monitor & Alarm package for early performance degradation alert.
|
|
BD : "The industry benchmark for desiccant dryers"
Incorporating unique, patented technological innovations and extra energy-saving options, Atlas Copco's BD desiccant dryers provide you with the clean, dry air you are in need of to expand the life of your equipment and ensure the quality of your end product.
- Dry air at any time
- Supreme energy efficiency
- Easy installation, Complete design, Plug & Play
- Advanced Control & Monitoring Solutions
- The Reliable choice
- Proven Peace of Mind
- Built for Endurance
|
|
|
Ingersoll Rand’s heatless desiccant dryers deliver superior compressed air quality at a constant -40°F to -100°F (-40°C to -70°C) pressure dew point. Our heatless dryers are simple to operate, dependable and very economical.
|
|
Champion Dessicant Dryers
CDT Series
Heatless Desiccant Compressed Air Dryers For pressure dew points of +38°F to -100°F, (+3°C to -73°C)
Basic Controller:
* The basic controller presents a traditional heatless drying
system.
* Using a simple timer based controller, it offers a reliable
fixed cycle operation.
* Automatic time controlled bed regeneration cycles offer
consistent performance.
* The controller LEDs reflect: power on, left tower drying,
right tower drying.
Standard Controller Features:
* Four dew point selections
* State-of-the-art Controller
* Purge Optimizer
* Programable shut-down capabilities
* Dew point performance per ISO 8573.1
|
|
BD : "The industry benchmark for desiccant dryers"
Incorporating unique, patented technological innovations and extra energy-saving options, Atlas Copco's BD desiccant dryers provide you with the clean, dry air you are in need of to expand the life of your equipment and ensure the quality of your end product.
- Dry air at any time
- Supreme energy efficiency
- Easy installation, Complete design, Plug & Play
- Advanced Control & Monitoring Solutions
- The Reliable choice
- Proven Peace of Mind
- Built for Endurance
|
|
Benefits:
- extremely small total height
- easily compatible with CLEARPOINT® filters
- top-grade design
- all functional components are built-in and well protected inside the housing
- guaranteed drying, as humidity is removed in any case
- no alteration of the usual compressed air composition
- low purge air demand
- service-free, as there are no wearing parts in the dryer (merely the regular change of the filter elements is required)
- no ecologically undesirable drying agents
|
|
|
The extremely efficient design ensures cost-saving and reliable operation. The technical highlights include: vertical heat exchanger arrangement with condensate flow from top to bottom (correct physics!), stainless steel demister for reliable separation, and a large calming space to prevent condensate carry-over.
|
|
Capacity Range: 10-150 cfm (0.28-4.2 m3/min)
Pressure Dew Point: 38°F (3°C)
ISO Class 4
Cooling Method: Air-cooled
Voltage: 115/1/60, 230/1/60, 230/1/50
Maximum Pressure: 230 psig (16 barg)
Maximum Ambient (air cooled): 113°F (45°C)
Maximum Inlet Temperature: 120°F (49°C)
Refrigerant: R-22 and R-404A
|
|
|
|
|
|
To customize the total air system for optimum efficiency, Quincy provides both Cycling and Non-Cycling refrigerated air dryers. Cycling dryers are of particular interest for larger systems with fluctuating loads, whereas Non-Cycling dryers are typically best suited for smaller systems or systems expecting fairly constant loads. Either way, one need not look any further than Quincy for time-proven and reliable compressed air dryers.
• Balanced refrigeration control systems
provide reliable and consistent performance
• User friendly control panels provide
operation data and instrumentation
• Microprocessor control on all noncycling
units over 600 cfm and all
cycling units 325 cfm & up allows
system versatility
• Application specific heat exchangers
render low pressure drop and optimum
performance
• Model specific Electronic no loss and
timer drains provide positive condensate
removal
• R-134a and R-404a refrigerants ensure
environmentally friendly operation
• Cold surface insulation improves
thermal efficiency
|
|
|
The ambient air given off by any compressor always contains water vapour. This depends on the ambient temperature and the relative humidity. When air is compressed, the volume decreases proportionally. This results in condensate formation. Condensate causes corrosion in compressed air pipe line, increases tool wear, faults in pneumatic controls, delayed response time, expensive down time, etc. Compressed air driers are used to separate the condensate and contaminants.
|
|
Champion Refrigerated Dryers
CRN Series 10-3000 scfm
Heat Transfer
RNC 10-15 models have the patented static condenser technology that eliminates the need for a cooling fan. These models include an on/off switch, longer power cord (8 ft), a timer operated drain with isolation valve on RNC, a float trap on RNC, and deliver heated outlet air to eliminate sweaty piping.
RNC models 25-50 benefit from our smooth handcrafted all copper heat exchangers.
Only large bore multiple tubes-in-tube designs efficiently split the airflow to acheive the
low pressure drop, high heat transfer.
RNC Series models 75-3000 incorporate heat exchangers crafted from multiple offset layers of press formed AISI 316 stainless steel. Press forming creates peaks and valleys that form media channels that are rich in fluid turbulence. This prevents fouling and maximizes engery efficiency.
|
|
|
|
|
|
Legendary CHA Series Heat-Les™ Dryers (1,800-12,100 scfm)
CHA Series Heat-Les™ desiccant compressed air dryer is the most reliable, energy efficient, large-flow heatless dryer available. Standard designs are offered for flows ranging from 1,800 to 12,100 scfm, pressures from 60 to 150 psig, and pressure dew points of -40°F to -100°F. Other sizes and pressures are available upon request. These dryers can be used in continuous or intermittent service, downstream of oil lubricated or oil-free compressors, and are compatible with corrosive, toxic or explosive environments. Every unit we build incorporates our AMLOC® energy management system to assure long component life cycles and maximum energy savings.
Simple design with few moving parts for economical first cost and dependable operation.
Legendary Century Series control valves feature stainless steel internal parts designed specifically for desiccant dryer service and tested to 1,000,000 cycles, bubble-tight.
Patented AMLOC® Energy Management System for maximum energy savings.
Advanced Dryer Control System (ADC) includes a functioning schematic for easy reference to system operation.
Down-flow drying extends desiccant life 5 to 7 years and prevents desiccant attrition during upset (fluidization) conditions.
|
|
Clean and dry compressed air: it is vital to power up your busy production environment. Containing moisture, aerosols and dirt particles, untreated compressed air poses a substantial risk as it can damage your air system and end product.
Incorporating unique, patented technological innovations and extra energy-saving options, Atlas Copco's FD refrigerant dryers provide you with the clean, dry air you are in need of to expand the life of your equipment and ensure the quality of your end product.
|
|
- Reliable operation with standard components tested for continuous service.
- The compact dryer can be installed on the fl oor (fl oor mounted kit as standard).
- The inlet prefi lter FMM and the outlet postfi lter FPRE, have to be mounted on the air distribution line. The fi lters are included but not pre-mounted.
Technical Info
- Capacities from 1917 up to 7800 l/1’ at 7 bar.
- Standard dew point -40°C.
- Max. working pressure 16 bar.
- Working pressure range 4 - 16 bar.
|
|
Xebec's line of adsorption dryers makes it easy to comply with evolving energy conservation requirements. A base model design supported by three progressive upgrades makes ADX Solutions a smart investment that pays off in world class performance and long-term peace of mind.
DESIGNED TO MEET ENERGY CONSERVATION NEEDS TODAY
Xebec's common platform design allows any dryer to be upgraded to the most efficient model available while maintaining the same outlet flow. Select a low cost Heatless model today and upgrade to an energy efficient Vacuum Regenerated Dryer tomorrow.
|
|
Solid performance
_Steady pressure dew point
_No freezing of condensed moisture
_No chance of moisture entering the compressed air system.
Simple reliability
_Quality components, generously sized
_Simple and proven design
_Effective control system (hot gas bypass).
|
|
As quality air from an oil-free air compressor is the requirement for your application, so dry air is equally desirable. For a quality end product and reliable production process Atlas Copco offers the unique range of MD adsorption dryers, specially designed to work with proven oil-free air Z-compressors.
Clean, oil-free, dry air
A reliable production process
A quality end product
Easy installation, delivered complete with piping to reduce costs
No loss of compressed air
Oil-free air condensate
Safeguarding the compressed air net
Oil-free Z-compressor / MD dryer - a proven and reliable combination
A cost-effective design
|
|
|
|
|
|
Technology : Adsorption Dryers.
Operating principle: Designed for extracting humidity from compressed air, these dryers consist of aluminium columns each of which contains two twin chambers filled with a desiccant agent which dries the compressed air crossing over it. When a chamber is in service (drying phase), the other is in regeneration mode.
Flow rates treated:
From 40 m3/h to 2040 m3/h
Values given for a pressure of 7 bar and aspiration at 1 bar and at 20°C.
Pressure Dew point:
- 40°C as standard (SM and SMH models)
- 20°C optional (SM230 to SM1200 models only)
- 70°C optional (SM and SMH models)
Standard equipment:
High resistance extruded aluminium construction. Humidity indicator for monitoring the quality of air supplied. Fast re-pressurisation valve providing easy commutation and improving reliability.
Regeneration method: By pressure variation (SM models) and temperature variation (SMH models): the saturated desiccant agent is regenerated using a small quantity of the treated compressed air (SM models) with an additional heat contribution through heating elements (SMH models only). The dilatation of that warm air which is changed from the circuit pressure to atmospheric pressure provides the means for extracting the humidity absorbed by the desiccant agent and thus for regenerating it. The heating elements (SMH models only) provide the means for significantly reducing the quantity of dry air used and at the same time the dryer's operating cost.
|
|
|
|
|
|
Technology: Adsorption Dryers.
Operating principle: Designed for extracting humidity from compressed air, these dryers consist of aluminium columns each of which contains two twin chambers filled with a desiccant agent which dries the compressed air crossing over it. When a chamber is in service (drying phase), the other is in regeneration mode.
Flow rates treated:
From 5.1 m3/h to 34 m3/h
Pressure Dew point:
- 40°C as standard
- 70°C optional
Standard equipment:
Integral high efficiency oil removal SCH filter and 2-in-1 type cartridge (consisting of SCR anti-particle filter and desiccant).
Electronic display with operating condition by LED and audible alarm. Condensates removal by integral pipes.
Corrosion-resistant protection by epoxy painting and alocrom treatment.
Regeneration method:
By pressure variation: a small quantity of the treated compressed air is taken to regenerate the saturated desiccant agent. The dilatation of that air which changes from the circuit pressure to atmospheric pressure provides the means for extracting the humidity absorbed by the desiccant and thus for regenerating it. The humidity is then dispersed into the atmosphere through the exhaust silencers.
Key points: Installation at the point of use: supply of dry air right where it is needed. Easy installation, small dimensions and reduced noise level. Fast, simple maintenance.
Applications:
Suitable for all users wanting to obtain dry compressed air for a specific application, thus avoiding unnecessary and costly full treatment of the whole of the air network.
|
|
KZP Series
Blower Purge Desiccant Air Dryers
(500 - 4,300 scfm)
KZP Series, Blower Purge Desiccant Dryers are 100% efficient at delivering full supply-side compressor capacity. As compressed air generation tends to be the most costly utility within a facility, KZP Series users benefit from the ability to purchase a less expensive air compressor and a 20% reduction in air compressor energy consumption. Eliminate purge air loss to align supply-side equipment with demand-side requirements to optimize your air system.
* Ambient air used for regeneration - no process gas lost to purge
* Quality process control valves provide dependable operation
* Optional Energy Management System for maximum energy savings
* Pre-mounted prefilter and afterfilter (other mounting options are available: duplex, block and bypass valves)
|
|
|
|
