|
|
Features
The Model 10BP is a high capacity regulator
that relieves excess pressure in a pneumatic
system.
The Model 10BP provides greater accuracy
than relief valves over a narrow pressure
range. The Model 10BP is an excellent choice
for a wide range of precision applications.
The Model 10BP has the following features:
- Control sensitivity of 1/8" water column
allows use in precision applications.
- A separate Control Chamber and Aspirator
Tube isolate the diaphragm from the main
flow to eliminate hunting and buzzing.
- Unit construction lets you service the Model
10BP without removing it from the line.
- Mounting Bracket is available.
|
|
74-3000 Series: Pressure Reducing Regulator
Semiconductor grade pressure reducing regulator. Available with inlet pressures up to 3,000 psi. For high flow applications. With several outlet pressure ranges up to 150 psi. 10 or 5 Ra internal surface finish. Tube stubs or metal face seal type connections.
|
|
Features
- Control sensitivity of 1/4" water column
variation allows use in precision applications.
- A compensating diaphragm lets the
regulator remain unaffected by supply
pressure changes.
- Flow of up to 40 SCFM with 100 psig
supply allows use in applications with high
flow requirements.
- An aspirator tube compensates downstream
pressure droop under flow conditions.
- A separate Control Chamber isolates the
diaphragm from the main flow to eliminate
hunting and buzzing.
- Unit construction lets you service the Model
30 without removing it from the line.
- Canadian Registration Number (CRN)
Certification for all territories and provinces
|
|
B3000
filter regulator, stainless steel throughout
5 and 50 µm, G1/8 - G1
outlet 0 - 3 / 50 bar, max. 6000 l/min
|
|
Features
- The no-brass construction is well suited to
harsh environments.
- Internal and external epoxy finish for
superior corrosion resistance
- Non-bleed design to reduce consumption
- Integral Relief Valve
- A Gauge Port provides convenient
pressure gauge mounting.
- The standard 5-micron filter minimizes
internal contamination.
- The Filter Dripwell contains a Drain Plug
to easily drain trapped liquids.
- Standard Tapped Exhaust
- Soft Relief Seat minimizes air loss
- Canadian Registration Number (CRN)
certification for all territories and
provinces.
|
|
|
The Type-100 is a high precision, multi-stage pressure regulator. This pressure controller provides the highest level of regulation accuracy and repeatability available. The Type-100 is ideal for applications that call for the utmost of control and maximum stability under variable operating conditions. A stainless steel measuring capsule is used as a sensing element to activate the high gain servo balanced control mechanism in which the main valve is controlled by a pilot valve.This allows for greater accuracy and eliminates many of the problems associated with conventional regulators using range springs and diaphragms.
|
|
|
The ControlAir Type-850 and Type-860 are compacts unit that provide low-cost, high performance pressure regulation of compressed air (Type 850 and Type 860) or water (Type 860). Designed specifically for the OEM market, these units are ideal for compressed air or water pressure control applications. The highly sensitive diaphragm-operated design delivers accurate downstream pressure by eliminating the problems caused by sticking in piston designs utilized by competitors. A molded rubber supply valve provides accurate regulation and prevents leakage.
|
|
C3
of plastic, modular design
5 and 20 µm, G1/4 - G1
outlet 0 - 8 bar, max. 8500 l/min
|
|
Filters, Regulators, and Lubricators (FRLs)
27 Modular Series Assemblies and Accessories
Filter, Regulator, Lubricator, trio (pictured)
- traditional trio design
- gauge packaged uninstalled for installation on either side
- bowl guard supplied standard
- filter, regulator, and lubricator options available
27 Series combo units offer pre-assembled units for fast installations. The integral filter/regulator offers space saving design. Duo and trio assemblies utilize the modular clamping system to ease installation.
Other Filters, Regulators, and Lubricator Products offered by Coilhose Pneumatics:
Economy Regulators
Pre-Set In-Line Pressure Regulators
Adjustable In-Line Pressure Regulators
In-Line Series F, R, Ls
Miniature Series F (also in Coalescing), R, Ls
Miniature Pro Line F, R, L, Assemblies and Accessories
25 Series F, R, L, A and A
26 Series F (also in C), R, L, A and A
27 Series Modular Series F(also in C), R, L, A and A
Heavy Duty Series F (also in C), R, L, A and Accessories
General Purpose Series F (also in C), R, L, A and A
Dessiccant Air Dryers
Mechanical Condensate Drains
Solid State Automatic Drain
Pressure Gauges
Vacuum and Hydraulic Gauges
|
|
THREE-UNIT CLOSE NIPPLED COMBINATION
14A Miniature Series
FEATURES:
Unique Deflector Plate Ensuring Maximum Water & Dirt Separation
Solid Control Piston with Lip Seal for Extended Life
Non-Rising Adjusting Knob
Proportional Oil Delivery Over a Wide Range of Air Flows
Generates Oil Particles of 5 Micron or Smaller Downstream to Lubricate Systems Having Complex Piping Arrangements
|
|
|
Compressed air is the lifeblood of every sprayshop and its effective management is vital to operator safety, efficiency and maintaining ultimate finish quality. The DeVilbiss DVFR range of air filter regulators and coalescers are manufactured using super resistant technopolymer materials used in the construction of the filter bodies ensuring total solvent resistance, while the state of the art rolling diaphragm technology ensures optimum air flow and precision control.
|
|
The FRL range is a complete line of components for the treatment of the compressed-air.
FILTER: Thread from 1/8 to 1". Filtration Grade from 5µm to 50µm. Maximum Pressure 15 bar.
REGULATOR: Thread from 1/8 to 1". Regulation Range from 0-2 to 0-12 bar. Max. Pressure 15 bar.
FILTER REGULATOR: Thread from 1/8 to 1''. Regulation Range from 0-2 to 0-12 bar. Filtration Grade from 5µm to 50µm. Max. Presssure 15 bar.
Condensate Exhaust System: Semi automatic - Manual or Automatic to vacuum-operated.
QUICK EXHAUST REGULATOR: Thread 1/8-1/4. Regulation Range from 0-2 to 0-12 bar. Max. Pressure 15 bar.
LUBRICATOR: Thread from 1/8 to 1''. Max. Pressure 15 bar. Oil Loading System: Manual or Automatic to vaccum-operated.
SHOT OFF VALVE: Thread from 1/8 to 1''. Max Pressure 15 bar. Drive System Manual, Pneumatic, Electropneumatic.
SOFT START VALVE: Thread from 1/8 to 1''. Max. Inlet Pressure 3-10 bar. Drive Sytem Electropneumatic.
FR-L, V-FR-L, F-R-L, V-R-L, F-L are available.
|
|
Assembled Combinations
Sizes Available: Miniature Series 1/8", 1/4" NPT and Compact Series 1/4", 3/8", 1/2" NPT
An assortment of filter, regulator, and lubricator combinations available.
|
|
Supply only "compressed air".
For compressed air, always use clean air chat does not contain corrosive gas.
Be sure to use non lubricated, filtrated dry air (équivalent to Class 1, 3, 2 - ISO 8571-3).
With a thorough understanding of compressed air characteristics, design a pneumatic circuit.
%u25A0 Where instantaneous stop holding at emergency stop is required, the same function as in the mechanical or hydraulic or electrical units cannot be expected.
%u25A0 There arise pop-up, jet-out and leaking phenomena caused by compressibility and expansibility, which are air characteristics.
Prior to use, always ensure that the product withstands the operating environ ment.
%u25A0 The product cannot be used in corrosive gas, chemical liquid solvent, water, water vapor (steam) and ozone atmosphère. When a product is exposed to water droplets, oil or metallic powder, such as spatters and chips, be sure to protect it.
%u25A0 No product can be used in the explosive gas atmosphère.
Always pay extra attention to the electric circuit during emergency stop, and cylinder opération, etc. during power failure.
Attach a "pressure switch" and "residual pressure discharge valve" to the compressed air inlet of the equi pment.
|
|
FRL's - 50 Series
High flow capacity FRL line - Filters, Regulators and Lubricators.
Features:
High Flow
High Pressure
T Handle Adjustment Regulator
Pilot Regulators to 2-1/2 NPT
Rugged Design
Metal Bowls with Sight Glass
1/4 to 1-1/2 NPT Size Range
Assemblies Available
FRL's - FlexiBlok FRL 14/22/32/42 Series
The Numatics 14, 22, 32, and 42 Series FlexiBlok¨ line is a series of high performance air preparation products. Introduced in 1997, the FlexiBlok¨ line is made from sturdy but light weight aluminum; perfect for applications such as robotic arms which cannot afford extra weight and less expensive to ship than zinc. The block head design with integrated mounting holes eliminates costly mounting plates and adapters, making the product easier to use and install. Private labeling is easy thanks to the special templates which snap securely in the front and back of the heads. These templates can be customized with names and/or logos; perfect for OEM applications.
The 14,22,32 series conforms to ISO 1179-1 and 228-1 requirements.
The 42 series will soon also conform to these requirements.
|
|
|
Norgren carries a complete range of air preparation products to fit any application. The most recent addition is the Excelon Pro, a no tools required, light weight FRL. Visit www.norgren.com/excelonpro for more information. All accessories are also available.
|
|
Max. primary pressure: Transparant bowl 12 Bar/170 PSI
Metal bowl 18 Bar/255 PSI
Temperature: 0-60° C
Water separation capacity: min 90 %
Effective bowl volume: Filter: 20 cc
Lubricator: 45 cc
Material: Housing: Zinc
Transparent bowl: Polycarbonate
Metal bowl: Zinc
Filterelement: Plastic
Top cover: Glassreinforced Polyamid
Diaghragm: Chloroprenerubber with nylon reinforcement
Other parts: Brass, nitrile rubbe
|
|
Max. primary pressure: Metal bowl 18 Bar/255 PSI
Temperature: 0-60 oC
Water separation capacity: min 90 %
Effective bowl volume: Filter 45 cc
Lubricator 120 cc
Material: Housing: Zinc
Metal bowl: Zinc
Filterelement: Plastic
Top cover: Glassreinforced polyamid
Diaghragm: Chloroprenerubber with nylon reinforcement
Other parts: Brass, nitrile rubber
|
|
airfit comfort (G3/8 - G1/2 - G3/4)
Operating comfort at the highest level. Down to the smallest detail.
That was the main challenge for HOERBIGER-ORIGA in the development of a new G1/2 series. The result is called airfit comfort - and it lives up to its name.
Advantages:
optimum price/performance ratio
high operating reliability
fast bowl change with bayonet fitting
direct wall-mounting possible
connects to G3/4 air lines using special adapter
corrosion resistant through high quality surface treatment of the zinc die-cast housing
modular design for easy interlock between components
comprehensive range of accessories
all environmentally relevant materials are identified
|
|
A range extended for the air conditioning:
Complete unit FRL, governor automatically-controlled, filters, membrane drier, pressurization progressive, gate valve. Flow from 150 to 10.500 possible Nl/min.
Many accessories for all applications
|
|
Connection guaranteed: a wide range of functions and variants - always harmonised to the respective requirements.
• Exhaust air/supply air flow control or without non-return function
• Flow rate 15 ... 4,300 l/min
• Threaded connectors M3 ... G3/4
• Push-in fittings QS3 ... QS 12 or PK-3 ... PK-6
• Variants with increased corrosion resistance
|
|
|
A family of in-line composite body flow controls, needle valves, and check valves that are tough and corrision resistant. Four stage, tapered needle design provides infinite control. Tamper resistant locking ring prevents unwanted adjustments to the valves. These can be used in-line or be panel mounted. ARO's 360 degree Swivel Right Angle Flow Controls are ready for installation on all ARO Cylinders.
|
|
The miniature Preset Flow Control is ideal for many applications involving pneumatic systems, including the control of cylinder speed.
The operation of the flow control is based on the movement of a small disc. The flat surface on one side of the orificed disc seals and permits flow through the orifice. The amount of flow permitted in the reverse direction is determined by the orifice size. In the forward direction full flow is permitted. The flow controls design allows a maximum supply pressure of 75 PSI with a minimum cracking pressure of less than 10” H2O. Orifice sizes are available from .004” to .040”.
|
|
| ... products without technical information |
| |
|
|
see the results for the following category
