|
|
Safely and Quickly Removes Tough Materials
Flow International Corporation's A-3000 ultra light hand tool combines the power of ultrahigh-pressure (UHP) water (and its relatively low water volumes) with extremely high nozzle rotation speeds. The result is a versatile tool that offers excellent removal rates for a wide variety of industrial cleaning projects.
This multi-purpose tool offers superior performance and control. Rotating a variety of multiple-orifice tips at up to 3,000 rpm, the A-3000 delivers as much as 6.5 gallons (22.7 liters) per minute of ultrahigh-pressure water. It is the only hand tool rated for operating pressures of 45,000 psi (3,100 bar).
Multiple Applications Multiply the Savings
The A-3000's high rotation speed makes it the ideal tool to remove the toughest coatings, including epoxies, resins, paint, rust, scale, calcium deposits and oxides. And because it is air-powered, the A-3000 is easily operated from any compressed air supply.
With its unmatched productivity and low water volumes, the A-3000 is an environmentally-sensible alternative to grit blasting, burning and chemical removal. The A-3000's light weight reduces operator fatigue so workers can work longer, and more safely.
Benefits
Reduced operator fatigue improves safety and productivity
Pneumatic power means no oil spills
High removal rates with minimal waste water
Standard Features
Remotely located on/off valve
Advanced ergonomic design
Lightweight
Patented swivel design allows quick change of high-pressure seals and easy maintenance
Second safety trigger requires operator to have both hands on tool for safe operation
Runs from any compressed air source with greater than 32 scfm at 90 psi
Flow patented HornetTM nozzles
Specifications
Tool weight: 11.0 lbs (4.98 kg)
Maximum operating pressure: 45,000 psi (3,100 bar)
Air required: 32 scfm @ 90 psi
Working rotation speed: 3,000 rpm
Motor horsepower: 0.7 hp (0.5 kW)
|
|
High Pressure Spray Gun/Lances
Heat resistant nylon trigger. Available with a variety of lances.
Normal flow rate: 10.5 gpm.
Pressure range: 2900 - 4050 psi.
Maximum temperature: 320º F.
Spray angle: adjustable from a straight jet to a large-angle spray.
Materials: fiberglass reinforced nylon (body), brass, 203 stainless steel, 440 stainless steel. Typical applications: high-pressure washing.
|
|
We are manufacturers of high pressure guns and wholesaler for Widoberg products.
Therefore if you wish to have a new automatic - or mecanic installation we offer you the most appropriate solution for your requirements.
We have highly qualified staff with a large experience in designing and adjusting installations. |
|
| ... products without technical information |
| |
The Hypro Series 5200 Big Twin® piston pump is suitable for applications in high pressure washers for industrial and agricultural cleaning needs. It is also useful as a sprayer pump to apply a wide range of chemicals.
The Series 5200 is constructed of cast iron body and cylinder heads, unitized stainless steel valve assemblies and double row ball bearing supported crankshaft. |
|
| Self-serve carwash and tunnel prep unit owners across the country are making the switch to Hypro’s 2300 Series plunger pumps. Backed by the best warranty in the industry, Hypro pumps are designed for, and not adapted to, the car wash industry, resulting in pumps that deliver higher pressure and increased reliability. |
|
| ... products without technical information |
| |
| ... products without technical information |
| |
> Main features
* Automatic loading system of the corner. * Automatic balancing system of the corner. * Cutting units shaft with double support * Four cutting units * Automatic working cycle driven by PLC* Automatic working cycle with automatic start. * Automatic working cycle with manual start, to work a frame with a extremely reduced “light – hole” * 1 Upper knife 3 x 0,5 mm to clean the upper weld bead. * 1 Lower knife 3 x 0,5 mm to clea the lower weld bead. * Profile support arms * Up and lower drilling unit for cleaning the gasket passage (ONLY FR4P) |
|
|
|
