|
|
Adjustable Air Amplifier - Nex Flow™:
- Adjustable Air Amplifier from Nex Flow™ is used for a variety of applications - either coated aluminum or stainless steel for high temperature and corrosive environments.
- Adjustable Air Amplifier is easy to mount and maintain. Compressed air consumption and noise levels are reduced.
- Adjustable Air Amplifier takes energy from a small volume of compressed air to produce high velocity, high volume, low pressure output airflow.
- Adjustable Air Amplifier is quiet, efficient and can amplify flows up to 20 times their input air consumption rate.
Specifications:
Stainless steel or coated aluminum are materials of construction. Three standard outlet (outside) diameters: 1-1/4" (31mm), 2" (51mm), 4" (200mm). Other sizes available upon request.
Come with a standard .002" (.05mm) gap that is adjustable. If greater force is required, the gap may be adjusted for greater flow.
|
|
HAA31 Models
Single-acting, single-stage air pressure amplifiers
3 models with ratios of (2.5:1), (3.5:1) & (4.5:1)
Maximum inlet pressure of 125 psi
Maximum outlet pressures from 320 psi to 600 psi
AA Models
Single-acting, single-stage air pressure amplifiers
3 models with ratios of (8:1), (15:1) & (30:1)
Maximum inlet pressures from 1,250 psi to 4,500 psi
Maximum outlet pressures from 2,500 psi to 4,500 psi
AAD Models
Double-acting, single-stage air pressure amplifier provides outlet flow on each stroke of cycle and gains "lift" from inlet pressure
4 models with ratios of (2:1), (5:1), (15:1) & (30:1)
Maximum inlet pressures from 300 psi to 4,500 psi
Maximum outlet pressures from 300 psi to 5,000 psi
AAT Models
Two-stage air pressure amplifier provides two high pressure pistons of different ratios within a single unit for maximum efficiency at higher outlet pressures
3 models with ratios of (7/30), (15/30) & (30/50)
Maximum inlet pressures from 300 psi to 3,000 psi
Maximum outlet pressures from 4,500 psi to 5,000 psi
|
|
|
ITW Vortec’s Round Transvectors use a small amount of filtered compressed air to deliver a large airflow for a wide range of conveying, ventilation, drying and cooling applications. The high-flow, bladeless blowers don’t require machine guards and are especially useful for removing plastic scrap and metal chips, ventilating fumes or smoke, and conveying small parts, pellets, powders and dust. As a vacuum or blowoff device, these air amplifiers are more compact and less expensive than variable-speed blowers and fans, provide instant on/off performance, and operate at low noise levels to meet OSHA requirements. Round Transvectors are easily mounted and, with no moving parts to wear out or break, are virtually maintenance-free. Used in ducted and unducted applications, Round Transvectors are available in several sizes, in both aluminum and stainless steel, and can deliver flow rates from 32 to 2300 SCFM.
|
|
FEATURES - BENEFITS - APPLICATIONS
- Compact: installs off the floor, out of the way, in any position.
- 2 connections: plant air in, amplified air out. (Pilot air connection is ptional for start-stop control with a PCV valve or solenoid valve and pressure switch).
- Can replace a dedicated air compressor: 10 HP size in a typical large plant spot requirement for 100 PSI when only 80 PSI is available. (Model 5A-DS-2)
- Replace bottled nitrogen: up to 700 PSI for air testing, lab or production. (Model 5A-DS-5)
TYPICAL APPLICATIONS FOR HIGHER AIR PRESSURE
- Valve actuators
- Air starters
- Bin vibrators
- Pneumatic drill motors
- Air clamps
- Air brakes
- Off road tires
- Pneumatic nailers,staplers, straping machines
- Air/oil hoists
- Air presses
|
|
MAXIMATOR PLV series air amplifiers are suitable for the compression of pressurised air or nitrogen. The units are capable of increasing normal pressures of 4 bar or 6 bar to the desired final pressures. The PLV Air Amplifiers are operated with normal shop air and are provided with a variety of amplification ratios.
All PLV Air Amplifiers can be supplied with an air control unit comprising a filter, pressure regulator with pressure gauge and an air shut-off valve. The desired operating pressure can be preset by means of the air control unit in correspondence with the different pressure ratios. We can offer you a choice between a standard PLV Air Amplifier Station or a customised solution.
|
|
|
Air driven amplifiers are used to bring shopair pressure to a higher level. Compression ratios of 1:2, 1:4 or even higher are possible. Amplifiers can be built as a system or with a reservoir. Applications are increasing cylinderforce, pressurising shopair locally and saving the lifetime of your compressor by reducing your maximum pressure.
|
|
CI series Compact Intensifiers are simple generic boosters that utilize a large pneumatic piston to intensify oil pressure with a smaller piston. The Product range includes 24 models. All are designed to be highly space efficient and low weight. The pressure chamber features two large full flow ports for easy filling and bleeding.
The pneumatic actuator is our standard low profile large Bore compact cylinder.
Features Include:
Rugged space efficient, low weight
Aluminum design
Long life/Low friction
Three mounting choices
Optional Magnetic piston (Option “ACI”)
|
|
General Information
- The Model 20 Pneumatic High Capacity Volume
Booster uses a pneumatic input signal to accurately
control output pressure
- A balanced Supply Valve minimizes the
effects of supply pressure variation
- An Aspirator Tube compensates downstream
pressure droop under flowing conditions
- Optional Adjustable By-Pass Needle Valve allows
tuning for optimum dynamic response (1:1 ratio only)
- Optional Fixed Negative Bias allows operation with
pneumatic devices that cannot be adjusted to zero
input pressure
- A separate Control Chamber isolates the diaphragm
from the main flow to eliminate hunting and buzzing
- Unit construction allows servicing without removal
- Mounting Bracket available
- Canadian Registration Number (CRN)
Certification for all territories and provinces
|
|
| ... products without technical information |
| |
Kistler offers pressure sensors, force sensors, torque sensors and accelerometers for applications of all kinds in research, development and manufacturing.
Charge amplifier with LCD display and menu-guided operation %u2013 all important settings are visible at a glance; direct display of measurand as well as maximum, minimum and mean values, LED status displays.
Applications
Measurement of mechanical quantities (pressure, force, acceleration) with piezoelectric sensors. Not recommended for indication measurements on engines!
Options
Voltage input with power supply for Piezotron sensor Type 5015Axxx1. Parallel interface IEEE-488 Type 5015Ax1xx.
|
|
The dominant source is input voltage noise
en, amplified by the non-inverting gain of the
transducer interface section (Fig.I.).
This latter is a function of the signal source
impedance, 1/w (Ct+Cc), and charge amplifier
transfer impedance 1/wCf being unity (best case)
for open circuit input.
|
|
|
High-performance, low-noise preamplifier that is ideal for a wide variety of applications including low-temperature measurements, optical detection, and audio engineering.
|
|
A low noise RF pre-amplifier with nominal 18dB gain covering the frequency range 5KHz to 1100MHz. This battery powered unit features low noise performance making it ideal for any application requiring wide band amplification of low level signals. The SA1020 is used in conjunction with the Log Periodic Antenna and the Line Impedance Stabilization Networks (LISNs).
|
|
|
RF Amplifiers backed by Worldwide Support and Service and a 3-Year Warranty. dc to 1000 MHz. 1 to 50,000 Watts. Linear, broadband and VSWR tolerant, with a wide range of uses and exceptional endurance even in the most difficult test scenarios, the AR RF/Microwave Instrumentation RF amplifier is the industry standard for benchmark performance.
|
|
RF broadband power amplifiers rated at or above 10W continuous output are supplied by Credence Technologies, Inc.
Our RF Power amplifiers have fixed gain, low distortion with excellent stability over a wide range of VSWR.
|
|
The SM2325-53LD is a 2300-2500 MHz* LDMOS amplifier designed for multiple wireless communications and RF heating applications in medical devices.
Features
- Mis-Match Protected
- Single Power Supply
- Temperature Compensation
Options
- Forward/Reverse Power
Detection
- Logic On/Off Control
- Heatsink
|
|
AR Worldwide - Modular RF applications were developed for total precision for MRI, ablation, radiation and other medical applications requiring durability, dependability and cost-efficiency.
Medical professionals depend on us for:
- Fast rise and fall times
- Phase and amplitude stability
- Extremely low noise floor
- Negligible RF droop
- Unconditional stability
- Infinite VSWR protection
- High accuracy output
- Temperature compensation
- Modular design
- Custom configuration
|
|
| ... products without technical information |
| |
|
|
see the results for the following category
