|
|
Power test systems are made for single-phase and three-phase power quality testing applications. Record and analyze power at any base frequency from milliHertz to 800 Hz, and still add any of the unique DEWETRON capabilities - video, GPS, additional analog sensors, etc. POWER QUALITY is as an add-on to just about any DEWETRON system, so please look at any of our multifunction systems as a platform.
|
|
Features:
- Mixture Viscosity
- Tool Condition
- Optimum Feed Rate
- Pump or Fan Flow
- Beginning or End Process
- Obstructions
- Overloads
- Loss of Load
|
|
Patented Autophase technology actually corrects common wiring errors. Analog and network models available. Click on the appropriate series to see details below...
...or select data sheets in PDF format from this list.
The AutoPhase Advantage
AutoPhase makes power transducer installation simple.
There are over 40 ways to wire up a 3 phase, 4 wire kW transducer. For example, reversing the orientation of a CT flips the output waveform, tricking ordinary watt transducers into thinking there is a 180 degree phase shift. Or if CT and voltage inputs are mismatched, the transducer thinks there is a 120 degree phase shift. Either way, you have a problem.
AutoPhase identifies the phases and polarity automatically and corrects for the error in software. This eliminates flashing "ERROR" lights, tedious and dangerous reconnecting of inputs. AutoPhase even tells you which CTs are reversed and which phases are mismatched!
|
|
Terasaki offers a cost effective solution for the measurement ofthe main
electrical parameters in electrical distribution networks.
The selection of the parameters to be measured can be easily visualised with the help of a clear and concise LED display.
Simple to set up with programmable CT. ratio from the front of the meter-Available in panel mounted and DIN rail mounted versions.
The fourth display allows simultaneous reading of two different parameters
Monitors the cubicle temperature
TheTEMM range offers a comprehensive selection of multifunction
meters to suit any application.
|
|
MV substation control unit
Description
Easergy T200I integrates within a single unit, all functions to remote control an MV substation:
Management of 1 to 16 switchgear/circuit breaker
Uninterruptible power supply 24 or 48 Vcc
Fault passage indicator
Current measurements
MV network reconfiguration automation functions
Local display and control
Large catolog of protocols:IEC 870-5-101 and 104, DNP3, Modbus and various customer owned protocols
Various transmission systems: Ethernet, RS232, Radio, PSTN, GSM, GPRS, private line...
|
|
| ... products without technical information |
| |
|
Kanomax Cleanroom Monitoring System (CRMS) provides an automated means to monitor and gather airborne particle count and other parameters level in controlled environments. CRMS allows users to perform a variety of functions from PC including the alteration of alarms information and viewing of particle count concentrations.
|
|
|
|
|
|
EVM-7 Environmental Monitor
Particulate and air quality monitoring in one instrument.
Quest Technologies EVM-7 offers the unique capability to simultaneously measure particulates (mass concentration), volatile organic compounds (VOCs), toxic gas, carbon dioxide (CO2), relative humidity, temperature and air velocity (with optional accessory).
Key Features
--------------------------------------------------------------------------------
Simultaneously Measure Particulate and Gas Concentrations
Reduces the need for multiple instruments
Lowers the cost of ownership.
Dial-in Rotary Impactor
Twist and click selection of particulate settings:
PM2.5, PM4, PM10 or TSP*
90° Light Scattering Photometer
Mass concentration engine offers real-time measurement of particulates.
Built in Sampling Pump for Gravimetric Analysis
Allows user to insert a 37 mm filter cassette to capture particulates for laboratory testing.
*Within the instrument’s measurement range.
Applications Include
--------------------------------------------------------------------------------
Work Site Monitoring
Industrial Fence Line Monitoring
Industrial Hygiene Surveys
Remediation Sampling
Military Site Evaluation
IAQ Walk Through & Stationary Studies
Internal Vehicle Sampling (aircraft, trains)
Air Quality Assessment
Construction/Mining Site Monitoring
VOC Screening and Monitoring
Time-History Assessment
Regulatory Compliance
For pricing and availability information regarding purchase, service or calibration, please email Customer Service.
|
|
The TITAN gas analysis system that represents a "total solution" to your next project could include:
- A modular industrial spectrometer designed for versatile external sample interfacing
- A selection of optimized gas cells
- Powerful AutoQuant Pro software
- High quality spectral reference libraries
- Assistance with method development, (including EPA and SEMATEC protocols)
|
|
| ... products without technical information |
| |
Automated surveillance of safety areas and open-air grounds, especially at night or under bad visual conditions.
Images of the automatic thermographic monitoring system IROD
|
|
The thermographic system VarioCAM® hr head of the German manufacturer JENOPTIK Laser, Optik, Systeme GmbH is suited for various measuring tasks up to real-time analysis in R&D.
microbolometer FPA detector with (384 x 288) or
(640 x 480) pixels
spectral range (7.5 ... 14) µm
optional digital real-time interface (FireWire/IEEE 1394)
50/60 Hz frame rate
compact design, low weight
rugged metal housing (IP 65)
wide standard temperature measuring range
various IR lenses, various accessories
optomechanic microscan-function provides up to (1,280 x 960) infrared pixels
|
|
| ... products without technical information |
| |
Detect foundation settlement in time
HYDRALIGN is an online monitoring system based on the measurement principle of a water level. The hydrostatic measurement system has various application areas and is especially suitable for long term monitoring of plants and machine foundations as well as monitoring of building settlements. The pressure sensors are permanently installed on the machine foundations to measure height changes exactly
|
|
|
|
|
|
FEATURES
The LMTX is a new system for the monitoring of hook load for telescopic cranes also when mechanical extensions are used. The system is composed by a transmission unit LIM-TX, which is hanged on crane hook, and by a receiver unit LIM-RX positioned in the control panel unit.
The LIM-TX is composed by a strain gauge pin for load detecting and by a micro controlled transmitter to send by radio the data weight to the receiver unit.
The new structure of the shackle hook group does not limit the lifting operations.
The unit LIM-RX has two functions: the show of the data weight through a four digits red display, the load limits control.
If used with mechanical extensions (up to four jibs) the LIM-RX allows, through a push button, to set the numbers of jibs and consequently to control the overload limits by a relay contact and a LED indication.
The device is included in SRD (Short Range Device) classification and uses a frequency band of 868.3 Mhz of free use (without any authorization).
The LIM-TX unit works with a battery rechargeable by the truck lighter and the LIM-RX unit works by a 12..24 voltage battery.
Free maintenance. No interference with the other on board radio devices.
APPLICATIONS
Load monitoring
Overload monitoring
|
|
| ... products without technical information |
| |
|
The TECHNA-CHECK® Tool Monitoring System, with its easy set-up software, has been developed to monitor for broken, worn and missing tools through spindle power monitoring or vibration analysis.
|
|
With today’s global competition, every company continues to look for more efficient solutions to optimize machining cycles, avoid scraps, and minimize machine downtimes. Machining process must become more sophisticated and streamlined to obtain higher efficiency and lower costs.
Marposs proposes a new product line dedicated to the continuous monitoring of the machine process through several types of sensors (static and dynamic force, vibration, power, temperature, etc). The sensors constantly control any machine function, thus allowing cycle optimization and the reduction of scraps and machine downtime.
|
|
Tool monitoring system DDU4
The DDU system for monitoring thread cutting and drilling processes serves
for the direct, real-time measuring of torque and axial forces with control
and breakage limits which can be fixed permanently, alternatively in N or in Nm. In combination with the ARTIS process monitoring systems CTM and ARTEC 4000, the following recognition becomes possible in addition
to the standard functions:
* tool wear
* missing tool
* defective thread holes
* different thread depths
* material contact
* tool breakage
|
|
The two twin-channel PME modules (MP85 and MP85DP) from HBM provide the optimum solution for monitoring press-fit and assembly operations.
Almost any commercially available transducer can be connected to the amplifiers which operate synchronously and in parallel. The industrial design and the standardized CANopen and Profibus DP interfaces, or digital I/Os alternatively ensure optimum connectivity to the automation environment.
Features and benefits:
Twin-channel amplifier
Comfortable integration into automation system via field bus interfaces
Intelligent signal conditioning and powerful algorithms for monitoring of the fitting process
Results can be saved directly in SPC format
Industrial design.
|
|
|
|
|
|
The PRO Module was developed for the monitoring of assembly and test applications. Its electronics are housed in a compact enclosure that is DIN rail mountabel for easy installation. The Ethernet port allows for easy communication back to the Promess application software running on a standard PC. Multiple PRO modules can also be network to a central data collection point. The PRO Module is powerful yet simple to use making it perfect for monitoring assembly applications such as press-fit, staking, crimping or riveting. On the other hand the system is powerful enough to tackle more demanding test applications where accurate hight speed data collection and advanced analysis are reuqired. Promess provides the complete system including electronics, software, sensors.
Promess will assist in the design and selection of the sensors best suited for your specific application as well as in the initial start-up.
Features
- In-process quality verification
- Part traceability
- 2 high speed 24 bis analog inputs per module
- 1 encoder input per module
- Compact modular design
- Defined database
- Data export funtions
- Fieldbus options
- Auto calibration for sensors
- Diagnostics for setup and trouble shooting
- Network multiple systems
|
|
|
|
|
|
Cap Inspector
The Cap Inspection System is specifically designed to be used with any induction heating cap sealing equipment. The advanced features and the flexibility of the system allow it to monitor a wide range of container sizes at various conveyor line speeds. The Cap Inspector will detect and respond to a number of faulty conditions occurring during the induction cap sealing process.
Features:
- Detects all typical fault conditions on a conveyor line during the cap sealing process: Missing Cap, Bottle Misalignment (offset from center line), Cocked or unscrewed cap, Bottle Down, Idle State / No Bottles.
- 4 Relay Outputs (Ready/Fault, Monitoring On, Line, Ejector)
- Easy to operate and user friendly design.Self learning "AUTO CONFIGURATION" feature.
- The Ejector (not included) can be located up to 10Ft away from the sensing system.
- 2x20 LCD Display with Backlight. 3 additional Status LEDs.
- Universal Supply Voltage (95 to 250V AC).
- Productivity rate (bottles/min) is constantly monitored and displayed.
- Small, compact, watertight design.
|
|
T400 Elite
Fixed Trip Point Bearing Temperature Monitoring System
Microprocessor controlled unit - monitors 8 zones with up to 6 bearings in each zone
Status LED's provide quick location of the hot bearing condition
Easy installation – no set up!
Extensive range of PTC sensors available from 50∫C to 120∫
Sensors replace existing grease points without loss of maintenance function
Alarm mute - with automatic time delayed reactivation
|
|
T500 Elite - HotBus system
- Serial Network for Continuous Remote Sensor Monitoring
- Preventative maintenance tool fully compatible with existing systems
- Accepts input signals from a total of 256 sensors
- User adjustable trip-points for alarm & shut-down
- “BUS VIEW” Easy-to-use graphical monitoring software available
- Utilises the "HotBus" communications system
|
|
Control your storage & incubation conditions
Guarantee your products quality
Ensure a complete traceability of the monitored parameters
LABGUARD 2 is THE solution...
Simple and wireless, it measures and records
in real time the different parameters : temperature, humidity, pressure, CO2...
and manages alarm in real time.
In one screen and a few clicks only...
|
|
|
|
see the results for the following category : 
